asked on

Cisco 2651 Router / VIC-2FXO Added, but not working?

I trying to install VIC2-FXO-EU to my cisco 2651 32/128M router but it doesn't work, i believe im using the correct IOS, when the router powers up the cards clearly seem to power up and link light on them but it shows this error:

Slot is empty or does not support clock participate
WIC slot is empty or does not support clock participate VIC2-FXO

however the card doesn't show up in the show ver command neither in the show inventory nor the sh diag which I provided them below.

now is the card faulty?

router51#sh ver
Cisco IOS Software, C2600 Software (C2600-IPVOICE-M), Version 12.4(12c), RELEASE
 SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 13-Jul-07 02:22 by prod_rel_team
 
ROM: System Bootstrap, Version 12.2(6r),  RELEASE SOFTWARE (fc1)
 
zwy51 uptime is 41 minutes
System returned to ROM by power-on
System image file is "flash:c2600-ipvoice-mz.124-12c.bin"
 
Cisco 2651 (MPC860P) processor (revision 0.0) with 127308K/3764K bytes of memory
.
Processor board ID JAD063202JV
M860 processor: part number 5, mask 2
2 FastEthernet interfaces
32K bytes of NVRAM.
32768K bytes of processor board System flash (Read/Write)
 
Configuration register is 0x2102
 
zwy51#
zwy51#sh ver
Cisco IOS Software, C2600 Software (C2600-IPVOICE-M), Version 12.4(12c), RELEASE
 SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 13-Jul-07 02:22 by prod_rel_team
 
ROM: System Bootstrap, Version 12.2(6r),  RELEASE SOFTWARE (fc1)
 
zwy51 uptime is 43 minutes
System returned to ROM by power-on
System image file is "flash:c2600-ipvoice-mz.124-12c.bin"
 
Cisco 2651 (MPC860P) processor (revision 0.0) with 127308K/3764K bytes of memory
.
Processor board ID JAD063202JV
M860 processor: part number 5, mask 2
2 FastEthernet interfaces
32K bytes of NVRAM.
32768K bytes of processor board System flash (Read/Write)
 
Configuration register is 0x2102
 
zwy51#sh inven
NAME: "2651 chassis", DESCR: "2651 chassis"
PID: C2600M-2FE        , VID: 0.0, SN: JAD063202JV
 
 
router51#sh diag
Slot 0:
        C2651 2FE Mainboard Port adapter, 2 ports
        Port adapter is analyzed
        Port adapter insertion time unknown
        EEPROM contents at hardware discovery:
        Hardware Revision        : 0.0
        PCB Serial Number        : FFFF
        Part Number              : 73-4638-05
        RMA History              : 00
        RMA Number               : 0-0-0-0
        Board Revision           : A0
        Deviation Number         : 0-0
        Product (FRU) Number     : C2600M-2FE
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 01 C0 41 00 00 C1 0B FF FF FF 46 46 46
          0x10: 46 FF FF FF FF 82 49 12 1E 05 04 00 81 00 00 00
          0x20: 00 42 41 30 80 00 00 00 00 FF FF FF FF FF FF FF
          0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
 
 
router51#

Open in new window

ASKER CERTIFIED SOLUTION

donmanrobb

membership

This solution is only available to members.

To access this solution, you must be a member of Experts Exchange.

Start Free Trial

SOLUTION

logic2

membership

This solution is only available to members.

To access this solution, you must be a member of Experts Exchange.

Start Free Trial

logic2

ah and note that for this router you will also need one of the carrier modules

logic2

oops ignore what i said previously except the link :)
just look at the link
2600 series is supported through using a carrier module NM-1V and NM-2V are you having this ?
i have checked cisco and you;d need to have the IOS 12.3(17c) or the latest 12.3(26) to support this

szwy

ASKER

no I don't have NM-1v nor the NM-2V, I thought I would be fine if I used one of the two available slots.
I also have 2611XM and 1721, can this card be used with these routers?

donmanrobb

It will work in the 2611XM but you'll need a NM-1V module

donmanrobb

Heres the supported platforms guide
http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b53c7.shtml#platsup

logic2

if you read the previous link i posted it will show u everything u need to know about this
its really nice and self explanatory

logic2

thanks for the points but why am i taking just 250 ? :)

szwy

ASKER

please don't get me wrong, I truly believe you have been great guidnece to me,
and since there are just the two of you here, i thought i will do good if I split the points between you guys, even thought i knew you have more input, i just wanted to show my respect.
if you were in my shoes wouldn't you do the same!

logic2

donna know i didnt ask for all the points :) its ok though my friend i learnt something new anyway and this is the most important