Still celebrating National IT Professionals Day with 3 months of free Premium Membership. Use Code ITDAY17

x
?
Solved

Cisco VOIP question (gateways)

Posted on 2009-03-31
2
Medium Priority
?
595 Views
Last Modified: 2012-05-06
I am looking to put in a Cisco VOIP system in a small office (along with CME and Unity Express). Everything makes sense, but I am a little unclear on one basic thing ...

I have a 2811 that will be a gateway between the PSTN and the Cisco CME system. It is my understanding that when inbound calls come in from the PSTN matching a pattern, they are sent to the CME system like so:

dial-peer voice 10 voip
destination-pattern 2...
session target ipv4:10.1.1.2

with 10.1.1.2 as the CME system (a 3800 series router).

But what about outbound calls to the rest of the world? In other words, how do I configure the 2811 to route outbound calls over the trunk line (FXO port) to the PSTN?
0
Comment
Question by:AsenathWaite
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
2 Comments
 
LVL 3

Accepted Solution

by:
dgboyd earned 200 total points
ID: 24032487
Hi, here is a sample config that should work for you.  This will go on your 2811 and send all inbound calls to the CME router and calls from the CME router out to the FXO ports.  I am assuming you have four FXO ports, but you could easily add more.

!
trunk group voicecalls
 hunt-scheme sequential both up
!
voice-port 0/0/0
 trunk-group voicecalls
 connection plar 8001
 description --------> FXO Port 0
 caller-id enable
!
voice-port 0/0/1
 trunk-group voicecalls
 connection plar 8001
 description --------> FXO Port 1
 caller-id enable
!
voice-port 0/0/2
 trunk-group voicecalls
 connection plar 8001
 description --------> FXO Port 2
 caller-id enable
!
voice-port 0/0/3
 trunk-group voicecalls
 connection plar 8001
 description --------> FXO Port 3
 caller-id enable
!
dial-peer voice 100 voip
 description --------------> CME Router
 destination-pattern 8001
 session target ipv4:10.1.1.2
 codec g711ulaw
 no vad
!
!
dial-peer voice 105 pots
 trunkgroup voicecalls
 description --------------------> Local
 destination-pattern 9[2-9]......
 forward-digits 7
!
dial-peer voice 106 pots
 trunkgroup voicecalls
 description --------------------> Long Distance
 destination-pattern 91[2-9].........
 forward-digits 11
!
dial-peer voice 107 pots
 trunkgroup voicecalls
 description --------------------> 911
 destination-pattern 9911
 forward-digits 3
!
dial-peer voice 109 pots
 trunkgroup voicecalls
 description --------------------> International
 destination-pattern 9011.T
 prefix 011
!
dial-peer voice 110 pots
 trunkgroup voicecalls
 description --------------------> Information
 destination-pattern 91411
 forward-digits 4
!
dial-peer voice 111 pots
 trunkgroup voicecalls
 description --------------------> Operator
 destination-pattern 90
 forward-digits 1
!
0
 

Author Closing Comment

by:AsenathWaite
ID: 31565002
Very good answer--exactly what I was looking for.
0

Featured Post

Eye-catchers on the conference table

Challenge: The i-unit group was not satisfied with the audio quality during remote meetings. They were looking for a portable solution with excellent audio quality for use in their conference room but also at their client’s offices.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Quality of Service (QoS) options are nearly endless when it comes to networks today. This article is merely one example of how it can be handled in a hub-n-spoke design using a 3-tier configuration.
How to set-up an On Demand, IPSec, Site to SIte, VPN from a Draytek Vigor Router to a Cyberoam UTM Appliance. A concise guide to the settings required on both devices
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

715 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question