Solved

Juniper J4350 GUI

Posted on 2009-03-31
9
721 Views
Last Modified: 2012-05-06
I am new Juniper routers.  I have worked exclusively on Cisco and Adtran for the last 16 years.  Where I work now, they have a Juniper J4350 and I am trying to figure out how to access the GUI.  The router was already configured and in production when I took this job and there are some additional items I want to configure that would be much simplier through the GUI.  I need some help.
0
Comment
Question by:Mhorrocks1962
  • 4
  • 2
9 Comments
 
LVL 32

Expert Comment

by:Kamran Arshad
Comment Utility
0
 

Author Comment

by:Mhorrocks1962
Comment Utility
Those pdf's are just informational datasheets.  I need to know how to enable it from the cli, because the web page does not come up when ip is typed into the browser.
0
 
LVL 32

Expert Comment

by:harbor235
Comment Utility


J-Web access is requires to to point your browser to an IP on the juniper box via http or https. You will be presented with a login page, provide appropriate input and login. You then choose configuration from the task bar.

harbor235 ;}
0
Network it in WD Red

There's an industry-leading WD Red drive for every compatible NAS system to help fulfill your data storage needs. With drives up to 8TB, WD Red offers a wide array of solutions for customers looking to build the biggest, best-performing NAS storage solution.  

 

Author Comment

by:Mhorrocks1962
Comment Utility
Ok, let's all assume for a minute that whoever set up the router (not me) disabled J-Web access.  How do I re-enable it??  Must be able to reenable from CLI because that's all thats available because J-Web access has been turned off.

The router is already configured, I need to make some changes and would like to see the options that are available through J-Web.
0
 
LVL 32

Accepted Solution

by:
harbor235 earned 500 total points
Comment Utility


user@host# system services web-management http


harbor235 ;}
0
 

Author Comment

by:Mhorrocks1962
Comment Utility
Since I am unfamiliar with Juniper, as I have stated my previous comments, I would just enter this at the far left and side with no () or anything?

Juniper CLI just reminds my so much of shell bash scripting.

Please be specific about how I enter that command, and if works you will walk away with 500 points.
0
 

Author Closing Comment

by:Mhorrocks1962
Comment Utility
Needed some specific guidance on inserting solution into the cli, but never received it.  Trial and error, but it worked.
Thanks for responding
0

Featured Post

NetScaler Deployment Guides and Resources

Citrix NetScaler is certified to support many of the most commonly deployed enterprise applications. Deployment guides provide in-depth recommendations on configuring NetScaler to meet specific application requirements.

Join & Write a Comment

The Cisco RV042 router is a popular small network interfacing device that is often used as an internet gateway. Network administrators need to get at the management interface to make settings, change passwords, etc. This access is generally done usi…
#Citrix #Citrix Netscaler #HTTP Compression #Load Balance
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

743 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

16 Experts available now in Live!

Get 1:1 Help Now