Solved

ASA 5510 Multiple contexts conf. ¿VPN user access Unsupported?

Posted on 2009-04-03
5
962 Views
Last Modified: 2013-11-16
Hello, I'm thinking to configure two diferent context on an ASA 5510, 1st for VPN users access, with 1st ISP (this is the use now, without contexts), and the 2nd context to configure access to a web server in a DMZ, from inside network and also from internet, via a 2nd ISP. BUT, I have read at Cisco web pages that VPN is UNSUPPORTED in multiple contexts scenario, Is this right?. I have a ASA 8.0(2)18 version.
Thank you in advance.
0
Comment
Question by:elbarbar
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 3
  • 2
5 Comments
 
LVL 43

Expert Comment

by:JFrederick29
ID: 24058835
Yes, correct, VPN is not supported in multiple context mode (unfortunately).
0
 

Author Comment

by:elbarbar
ID: 24061090
Ok, then I'll need some other vpn server to use multiple context and Ipsec vpn access for my users, is this the only way?.
Thank you.
0
 
LVL 43

Expert Comment

by:JFrederick29
ID: 24061125
Yeah, or just run single context.
0
 

Author Comment

by:elbarbar
ID: 24061213
Right, but then I think I can not have 2 ISP lines and use the 1st to access a web server in a dmz, and the 2nd for vnp users access and default outside route to internet. I have tried and I could only get one of these depending on the default route in single mode. Do you know any way?
0
 
LVL 43

Accepted Solution

by:
JFrederick29 earned 500 total points
ID: 24061427
Yeah, you are correct, you can't do that in single context mode unless you specifically route the VPN addresses out the VPN interface (of course this really only works for site to site).  Unfortunately you'll need two physical boxes (one for VPN and one for Internet) if you want to keep VPN and Internet/DMZ separate.
0

Featured Post

Technology Partners: We Want Your Opinion!

We value your feedback.

Take our survey and automatically be enter to win anyone of the following:
Yeti Cooler, Amazon eGift Card, and Movie eGift Card!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Access points not passing on DHCP, because of Draytek PoE Switch (VLAN related) 18 82
Network over eigrp 100 topology ? 3 90
Cisco AnyConnect VPN 4 37
Cisco Nexus 5 49
To setup a SonicWALL for policy based routing to be used with the Websense Content Gateway there are several steps that need to be completed. Below is a rough guide for accomplishing this. One thing of note is this guide is intended to assist in the…
From Cisco ASA version 8.3, the Network Address Translation (NAT) configuration has been completely redesigned and it may be helpful to have the syntax configuration for both at a glance. You may as well want to read official Cisco published AS…
As a trusted technology advisor to your customers you are likely getting the daily question of, ‘should I put this in the cloud?’ As customer demands for cloud services increases, companies will see a shift from traditional buying patterns to new…
Both in life and business – not all partnerships are created equal. Spend 30 short minutes with us to learn:   • Key questions to ask when considering a partnership to accelerate your business into the cloud • Pitfalls and mistakes other partners…

738 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question