Solved

Linksys RVS4000 router locks up

Posted on 2009-04-06
2
1,220 Views
Last Modified: 2012-05-06
The router has the latest firmware and will be running along fine then just lockup, have to power cycle it to get it running again and if I check the log after this event, this is the vpn log ( I DO NOT have vpn enabled) and the date is set back to dec 31?? Can anyone tell me why? Is this router bad?


Dec 31 19:00:36 - [VPN Log]: Starting Pluto (Openswan Version cvs2006Jan12_11:29:56 X.509-1.5.4 PLUTO_SENDS_VENDORID PLUTO_USES_KEYRR; Vendor ID OE@ECqImzhFD)
Dec 31 19:00:36 - [VPN Log]: @(#) built on Oct 9 2008:14:19:20:
Dec 31 19:00:36 - [VPN Log]: Setting NAT-Traversal port-4500 floating to on
Dec 31 19:00:36 - [VPN Log]: port floating activation criteria nat_t=1/port_fload=1
Dec 31 19:00:36 - [VPN Log]: including NAT-Traversal patch (Version 0.6c)
Dec 31 19:00:36 - [VPN Log]: ike_alg_register_enc(): Activating OAKLEY_AES_CBC: Ok (ret=0)
Dec 31 19:00:36 - [VPN Log]: starting up 1 cryptographic helpers
Dec 31 19:00:36 - [VPN Log]: started helper pid=420 (fd:5)
Dec 31 19:00:37 - [VPN Log]: Using KLIPS IPsec interface code on 2.4.27-star
Dec 31 19:00:37 - [VPN Log]: Changing to directory '/etc/ipsec.d/cacerts'
Dec 31 19:00:37 - [VPN Log]: Changing to directory '/etc/ipsec.d/aacerts'
Dec 31 19:00:37 - [VPN Log]: Changing to directory '/etc/ipsec.d/ocspcerts'
Dec 31 19:00:37 - [VPN Log]: Changing to directory '/etc/ipsec.d/crls'
Dec 31 19:00:37 - [VPN Log]: Warning: empty directory
Apr 6 01:19:22 - [VPN Log]: shutting down
Apr 6 01:19:24 - [VPN Log]: Starting Pluto (Openswan Version cvs2006Jan12_11:29:56 X.509-1.5.4 PLUTO_SENDS_VENDORID PLUTO_USES_KEYRR; Vendor ID OE@ECqImzhFD)
Apr 6 01:19:24 - [VPN Log]: @(#) built on Oct 9 2008:14:19:20:
Apr 6 01:19:24 - [VPN Log]: Setting NAT-Traversal port-4500 floating to on
Apr 6 01:19:24 - [VPN Log]: port floating activation criteria nat_t=1/port_fload=1
Apr 6 01:19:24 - [VPN Log]: including NAT-Traversal patch (Version 0.6c)
Apr 6 01:19:24 - [VPN Log]: ike_alg_register_enc(): Activating OAKLEY_AES_CBC: Ok (ret=0)
Apr 6 01:19:24 - [VPN Log]: starting up 1 cryptographic helpers
Apr 6 01:19:24 - [VPN Log]: started helper pid=904 (fd:5)
Apr 6 01:19:25 - [VPN Log]: Using KLIPS IPsec interface code on 2.4.27-star
Apr 6 01:19:25 - [VPN Log]: Changing to directory '/etc/ipsec.d/cacerts'
Apr 6 01:19:25 - [VPN Log]: Changing to directory '/etc/ipsec.d/aacerts'
Apr 6 01:19:25 - [VPN Log]: Changing to directory '/etc/ipsec.d/ocspcerts'
Apr 6 01:19:25 - [VPN Log]: Changing to directory '/etc/ipsec.d/crls'
Apr 6 01:19:25 - [VPN Log]: Warning: empty directory


Then also the SYSTEM LOG:

Dec 31 19:00:08 - bind 0.0.0.0 - Address already in use
Dec 31 19:00:46 - Enable Tcp Connection Tracking
Dec 31 19:00:46 - The Total Used Table Memory Size = 0xFB4878 = 16082K
Dec 31 19:00:46 - Trying to free free IRQ16
Dec 31 19:00:46 - Trying to free free IRQ17
Dec 31 19:00:51 - Kris is unlocked
Dec 31 19:00:51 - Reset IDP Engine!!!
Dec 31 19:00:51 - The Total Used Table Memory Size = 0xFB4878 = 16082K
Dec 31 19:00:51 - Enable DDOS Detection!!
Dec 31 19:00:51 - Enable PortScan Detection!!
Dec 31 19:00:51 - Enable IP Sweep Detection!!
Dec 31 19:00:52 - This is a LinkSys Device.
Apr 6 01:19:22 - IPSEC EVENT: KLIPS device ipsec0 shut down.
0
Comment
Question by:Bang-O-Matic
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
2 Comments
 
LVL 32

Accepted Solution

by:
Kamran Arshad earned 500 total points
ID: 24086241
Hi,

Have you reset the router? If you can easily re-configure it then do a hard-reset and reconfigure it.
0
 

Author Comment

by:Bang-O-Matic
ID: 24092440
I will try that and let you know.
0

Featured Post

Increase Agility with Enabled Toolchains

Connect your existing build, deployment, management, monitoring, and collaboration platforms. From Puppet to Chef, HipChat to Slack, ServiceNow to JIRA, Splunk to New Relic and beyond, hand off data between systems to engage the right people.

Connect with xMatters.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

In the hope of saving someone else's sanity... About a year ago we bought a Cisco 1921 router with two ADSL/VDSL EHWIC cards to load balance local network traffic over the two broadband lines we have, but we couldn't get the routing to work consi…
When it comes to security, there are always trade-offs between security and convenience/ease of administration. This article examines some of the main pros and cons of using key authentication vs password authentication for hosting an SFTP server.
Here's a very brief overview of the methods PRTG Network Monitor (https://www.paessler.com/prtg) offers for monitoring bandwidth, to help you decide which methods you´d like to investigate in more detail.  The methods are covered in more detail in o…
Michael from AdRem Software explains how to view the most utilized and worst performing nodes in your network, by accessing the Top Charts view in NetCrunch network monitor (https://www.adremsoft.com/). Top Charts is a view in which you can set seve…

695 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question