Enabling all mouse buttons on Trust MI-6950R with Ubuntu 8.10
I'm trying to get all of the mouse buttons on my Trust MI-6950R to work with Ubuntu 8.10. The mouse has left/right mouse buttons, the scroll wheel (which can tilted left/right as well), zoom in and zoom out buttons, and forward/back buttons. Only the scroll wheel and left/right mouse buttons work with this entry in xorg.conf:
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
EndSection
So I researched a little on ubuntuforums and Google and came up with some new stuff to try. First, I tried the command: cat /proc/bus/input/devices (full output in the code section). When I did this, I noticed this entry in particular:
I: Bus=0003 Vendor=04fc Product=0801 Version=0111
N: Name="USB Multi-Smart Mouse"
P: Phys=usb-0000:00:12.0-2/in
S: Sysfs=/devices/pci0000:00/
U: Uniq=
H: Handlers=kbd mouse2 event4
B: EV=1f
B: KEY=837fff002c3027 bf00444400000000 f1f0001 f848a27c000 667bfad9415fed 8e000000000000 0
B: REL=1c3
B: ABS=100000000
B: MSC=10
Looks like what I'm looking for. So next, I tried to run "xev" to figure out the buttons section of the xorg.conf. The button results look like this:
Left Main: 1
Center (Scroll Button Pushed): 2
Right Main: 3
Scroll Up: 4
Scroll Down: 5
Wheel Tilt Left: (no button or event shown when pressed)
Wheel Tilt Right: (no button or event shown when pressed)
Zoom In: (no button or event shown when pressed)
Zoom Out: (no button or event shown when pressed)
Side Button/Back: 8
Side Button/Forward: 9
Counting the wheel tilting and all, the mouse has 11 buttons. Given that, I changed my xorg.conf to this:
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "Protocol" "evdev"
Option "Dev Name" "USB Multi-Smart Mouse"
Option "Dev Phys" "usb-*/input0"
Option "Device" "/dev/input/event4"
Option "Buttons" "11"
Option "ZAxisMapping" "4 5"
EndSection
I then restart X. When I get to the login screen, the mouse doesn't respond at all. I can move it, but the cursor doesn't go anywhere. I hit CTRL-ALT-F5 and changed the config back to the original one, restarted X, and the mouse started working fine again.
I'm not sure what I'm doing wrong to cripple the mouse. I'm also not sure of how to get the zoom in/out buttons working, or how exactly the ZAxisMapping should look. Would the scroll up/down, zoom in/out, and tilt left/right all be entered under ZAxisMapping, or just the scroll up/down?
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "CorePointer"
EndSection
So I researched a little on ubuntuforums and Google and came up with some new stuff to try. First, I tried the command: cat /proc/bus/input/devices (full output in the code section). When I did this, I noticed this entry in particular:
I: Bus=0003 Vendor=04fc Product=0801 Version=0111
N: Name="USB Multi-Smart Mouse"
P: Phys=usb-0000:00:12.0-2/in
S: Sysfs=/devices/pci0000:00/
U: Uniq=
H: Handlers=kbd mouse2 event4
B: EV=1f
B: KEY=837fff002c3027 bf00444400000000 f1f0001 f848a27c000 667bfad9415fed 8e000000000000 0
B: REL=1c3
B: ABS=100000000
B: MSC=10
Looks like what I'm looking for. So next, I tried to run "xev" to figure out the buttons section of the xorg.conf. The button results look like this:
Left Main: 1
Center (Scroll Button Pushed): 2
Right Main: 3
Scroll Up: 4
Scroll Down: 5
Wheel Tilt Left: (no button or event shown when pressed)
Wheel Tilt Right: (no button or event shown when pressed)
Zoom In: (no button or event shown when pressed)
Zoom Out: (no button or event shown when pressed)
Side Button/Back: 8
Side Button/Forward: 9
Counting the wheel tilting and all, the mouse has 11 buttons. Given that, I changed my xorg.conf to this:
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "Protocol" "evdev"
Option "Dev Name" "USB Multi-Smart Mouse"
Option "Dev Phys" "usb-*/input0"
Option "Device" "/dev/input/event4"
Option "Buttons" "11"
Option "ZAxisMapping" "4 5"
EndSection
I then restart X. When I get to the login screen, the mouse doesn't respond at all. I can move it, but the cursor doesn't go anywhere. I hit CTRL-ALT-F5 and changed the config back to the original one, restarted X, and the mouse started working fine again.
I'm not sure what I'm doing wrong to cripple the mouse. I'm also not sure of how to get the zoom in/out buttons working, or how exactly the ZAxisMapping should look. Would the scroll up/down, zoom in/out, and tilt left/right all be entered under ZAxisMapping, or just the scroll up/down?
My xorg.conf:
Section "Monitor"
Identifier "Configured Monitor"
EndSection
Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
Device "Configured Video Device"
DefaultDepth 24
EndSection
Section "Module"
Load "glx"
EndSection
Section "Device"
Identifier "Configured Video Device"
Driver "nvidia"
Option "NoLogo" "True"
EndSection
Section "InputDevice"
Identifier "Generic Keyboard"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "Protocol" "evdev"
Option "Dev Name" "USB Multi-Smart Mouse"
Option "Dev Phys" "usb-*/input0"
Option "Device" "/dev/input/event4"
Option "Buttons" "10"
Option "ZAxisMapping" "4 5"
EndSection
Section "ServerFlags"
Option "AutoAddDevices" "false"
EndSection
============================================
cat /proc/bus/input/devices:
I: Bus=0017 Vendor=0001 Product=0001 Version=0100
N: Name="Macintosh mouse button emulation"
P: Phys=
S: Sysfs=/devices/virtual/input/input0
U: Uniq=
H: Handlers=mouse0 event0
B: EV=7
B: KEY=70000 0 0 0 0
B: REL=3
I: Bus=0011 Vendor=0001 Product=0001 Version=ab41
N: Name="AT Translated Set 2 keyboard"
P: Phys=isa0060/serio0/input0
S: Sysfs=/devices/platform/i8042/serio0/input/input1
U: Uniq=
H: Handlers=kbd event1
B: EV=120013
B: KEY=402000000 3803078f800d001 feffffdfffefffff fffffffffffffffe
B: MSC=10
B: LED=7
I: Bus=0003 Vendor=050d Product=0815 Version=0110
N: Name="Honey Bee Nostromo SpeedPad2 "
P: Phys=usb-0000:00:12.0-1/input0
S: Sysfs=/devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.0/input/input2
U: Uniq=
H: Handlers=kbd event2
B: EV=100013
B: KEY=e080ffdf01cfffff fffffffffffffffe
B: MSC=10
I: Bus=0003 Vendor=050d Product=0815 Version=0110
N: Name="Honey Bee Nostromo SpeedPad2 "
P: Phys=usb-0000:00:12.0-1/input1
S: Sysfs=/devices/pci0000:00/0000:00:12.0/usb3/3-1/3-1:1.1/input/input3
U: Uniq=
H: Handlers=mouse1 event3
B: EV=20017
B: KEY=70000 0 0 0 0
B: REL=103
B: MSC=10
B: LED=7
I: Bus=0003 Vendor=04fc Product=0801 Version=0111
N: Name="USB Multi-Smart Mouse"
P: Phys=usb-0000:00:12.0-2/input0
S: Sysfs=/devices/pci0000:00/0000:00:12.0/usb3/3-2/3-2:1.0/input/input4
U: Uniq=
H: Handlers=kbd mouse2 event4
B: EV=1f
B: KEY=837fff002c3027 bf00444400000000 f1f0001 f848a27c000 667bfad9415fed 8e000000000000 0
B: REL=1c3
B: ABS=100000000
B: MSC=10
I: Bus=0019 Vendor=0000 Product=0002 Version=0000
N: Name="Power Button (FF)"
P: Phys=LNXPWRBN/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
U: Uniq=
H: Handlers=kbd event5
B: EV=3
B: KEY=10000000000000 0
I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button (CM)"
P: Phys=PNP0C0C/button/input0
S: Sysfs=/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input6
U: Uniq=
H: Handlers=kbd event6
B: EV=3
B: KEY=10000000000000 0
I: Bus=0010 Vendor=001f Product=0001 Version=0100
N: Name="PC Speaker"
P: Phys=isa0061/input0
S: Sysfs=/devices/platform/pcspkr/input/input7
U: Uniq=
H: Handlers=kbd event7
B: EV=40001
B: SND=6
gheist
ZAxisMapping "4 5 6 7" and so on...
ASKER
I tried changing ZAxisMapping to both "4 5 6 7" and "4 5 6 7 10 11" but neither had an impact on the issue. The mouse still does not function at all when using the second configuration I posted. I tried replacing event4 with mouse2 to see if that had a difference and that didn't work either.
Do you have multiple mouses?
ASKER
No, although I have a Nostromo n52 gamepad attached (I'm not sure if that is part of the issue):
I: Bus=0003 Vendor=050d Product=0815 Version=0110
N: Name="Honey Bee Nostromo SpeedPad2 "
P: Phys=usb-0000:00:12.0-1/in
S: Sysfs=/devices/pci0000:00/
U: Uniq=
H: Handlers=kbd event2
B: EV=100013
B: KEY=e080ffdf01cfffff fffffffffffffffe
B: MSC=10
I: Bus=0003 Vendor=050d Product=0815 Version=0110
N: Name="Honey Bee Nostromo SpeedPad2 "
P: Phys=usb-0000:00:12.0-1/in
S: Sysfs=/devices/pci0000:00/
U: Uniq=
H: Handlers=mouse1 event3
B: EV=20017
B: KEY=70000 0 0 0 0
B: REL=103
B: MSC=10
B: LED=7
I: Bus=0003 Vendor=050d Product=0815 Version=0110
N: Name="Honey Bee Nostromo SpeedPad2 "
P: Phys=usb-0000:00:12.0-1/in
S: Sysfs=/devices/pci0000:00/
U: Uniq=
H: Handlers=kbd event2
B: EV=100013
B: KEY=e080ffdf01cfffff fffffffffffffffe
B: MSC=10
I: Bus=0003 Vendor=050d Product=0815 Version=0110
N: Name="Honey Bee Nostromo SpeedPad2 "
P: Phys=usb-0000:00:12.0-1/in
S: Sysfs=/devices/pci0000:00/
U: Uniq=
H: Handlers=mouse1 event3
B: EV=20017
B: KEY=70000 0 0 0 0
B: REL=103
B: MSC=10
B: LED=7
Check what X -configure produces with gamepad detached...
Also post /var/log/Xorg.0.log - if it reads from event device that it has 10 buttons.
ASKER
/var/log/Xorg.0.log:
(WW) Configured Mouse: No Device specified, looking for one...
(II) Configured Mouse: Setting Device option to "/dev/input/mice"
(--) Configured Mouse: Device: "/dev/input/mice"
(==) Configured Mouse: Protocol: "Auto"
(**) Option "CorePointer"
(**) Configured Mouse: always reports core events
(**) Option "Device" "/dev/input/mice"
(==) Configured Mouse: Emulate3Buttons, Emulate3Timeout: 50
(**) Configured Mouse: ZAxisMapping: buttons 4 and 5
(**) Configured Mouse: Buttons: 9
(**) Configured Mouse: Sensitivity: 1
In the code section, I've also posted the results of cat /proc/bus/input/devices when the Nostromo pad is not connected. I noticed that it shows the handlers are "kbd mouse1 event2" now instead of "kbd mouse2 event4"
(WW) Configured Mouse: No Device specified, looking for one...
(II) Configured Mouse: Setting Device option to "/dev/input/mice"
(--) Configured Mouse: Device: "/dev/input/mice"
(==) Configured Mouse: Protocol: "Auto"
(**) Option "CorePointer"
(**) Configured Mouse: always reports core events
(**) Option "Device" "/dev/input/mice"
(==) Configured Mouse: Emulate3Buttons, Emulate3Timeout: 50
(**) Configured Mouse: ZAxisMapping: buttons 4 and 5
(**) Configured Mouse: Buttons: 9
(**) Configured Mouse: Sensitivity: 1
In the code section, I've also posted the results of cat /proc/bus/input/devices when the Nostromo pad is not connected. I noticed that it shows the handlers are "kbd mouse1 event2" now instead of "kbd mouse2 event4"
I: Bus=0017 Vendor=0001 Product=0001 Version=0100
N: Name="Macintosh mouse button emulation"
P: Phys=
S: Sysfs=/devices/virtual/input/input0
U: Uniq=
H: Handlers=mouse0 event0
B: EV=7
B: KEY=70000 0 0 0 0
B: REL=3
I: Bus=0011 Vendor=0001 Product=0001 Version=ab41
N: Name="AT Translated Set 2 keyboard"
P: Phys=isa0060/serio0/input0
S: Sysfs=/devices/platform/i8042/serio0/input/input1
U: Uniq=
H: Handlers=kbd event1
B: EV=120013
B: KEY=402000000 3803078f800d001 feffffdfffefffff fffffffffffffffe
B: MSC=10
B: LED=7
I: Bus=0003 Vendor=04fc Product=0801 Version=0111
N: Name="USB Multi-Smart Mouse"
P: Phys=usb-0000:00:12.0-2/input0
S: Sysfs=/devices/pci0000:00/0000:00:12.0/usb1/1-2/1-2:1.0/input/input2
U: Uniq=
H: Handlers=kbd mouse1 event2
B: EV=1f
B: KEY=837fff002c3027 bf00444400000000 f1f0001 f848a27c000 667bfad9415fed 8e000000000000 0
B: REL=1c3
B: ABS=100000000
B: MSC=10
I: Bus=0019 Vendor=0000 Product=0002 Version=0000
N: Name="Power Button (FF)"
P: Phys=LNXPWRBN/button/input0
S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
U: Uniq=
H: Handlers=kbd event3
B: EV=3
B: KEY=10000000000000 0
I: Bus=0019 Vendor=0000 Product=0001 Version=0000
N: Name="Power Button (CM)"
P: Phys=PNP0C0C/button/input0
S: Sysfs=/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
U: Uniq=
H: Handlers=kbd event4
B: EV=3
B: KEY=10000000000000 0
I: Bus=0010 Vendor=001f Product=0001 Version=0100
N: Name="PC Speaker"
P: Phys=isa0061/input0
S: Sysfs=/devices/platform/pcspkr/input/input5
U: Uniq=
H: Handlers=kbd event5
B: EV=40001
B: SND=6
OK - it reads config from event device
Probably it fixes with spec of 1st device in error.
Are your buttons working now?
Probably it fixes with spec of 1st device in error.
Are your buttons working now?
ASKER
No, the mouse is doing the same thing. It just doesn't work at all when I try to use the configuration to enable the mouse buttons.
I'm using evdev as the protocol because that's what I had seen being used by others. I don't know if that's necessarily correct though. Is there another protocol I should try using, and if so, how will it change the other lines for the mouse's config?
I'm using evdev as the protocol because that's what I had seen being used by others. I don't know if that's necessarily correct though. Is there another protocol I should try using, and if so, how will it change the other lines for the mouse's config?
How it does not work? All diagnostics so far show it does...
run xev in X11, then press buttons above its window. Are they received by X11 ?
run xev in X11, then press buttons above its window. Are they received by X11 ?
ASKER
Oh that xorg.0.log is with the default configuration in place. The mouse works, except for the zoom in/out buttons and the forward/back buttons on the left side of the mouse. When I have xev running, if I press the zoom in/out buttons on the mouse, nothing shows up. The forward/back buttons on the left side of the mouse register in xev as buttons 8 and 9, but if I try to use them in any programs or games that I have (for example, WoW), they don't work. I can't map them to anything. Under Windows, however, I can.
Now if I use this configuration below in xorg.conf, the mouse doesn't work at all. No buttons respond and the cursor won't move.
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "Protocol" "evdev"
Option "Dev Name" "USB Multi-Smart Mouse"
Option "Dev Phys" "usb-*/input0"
Option "Device" "/dev/input/event2"
Option "Buttons" "9"
Option "ZAxisMapping" "4 5"
EndSection
Note that I changed the device to /dev/input/event2 (this is because I tried it again without the Nostromo pad attached). I've also tried setting ZAxisMapping to "4 5", "4 5 6 7", "4 5 6 7 8 9", and "4 5 8 9" with no difference in behavior.
I'm not at that computer at the moment, but when I get back to it I will post an xorg.0.log with the above configuration in place (when the mouse doesn't work at all) in case maybe that will help.
Now if I use this configuration below in xorg.conf, the mouse doesn't work at all. No buttons respond and the cursor won't move.
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "Protocol" "evdev"
Option "Dev Name" "USB Multi-Smart Mouse"
Option "Dev Phys" "usb-*/input0"
Option "Device" "/dev/input/event2"
Option "Buttons" "9"
Option "ZAxisMapping" "4 5"
EndSection
Note that I changed the device to /dev/input/event2 (this is because I tried it again without the Nostromo pad attached). I've also tried setting ZAxisMapping to "4 5", "4 5 6 7", "4 5 6 7 8 9", and "4 5 8 9" with no difference in behavior.
I'm not at that computer at the moment, but when I get back to it I will post an xorg.0.log with the above configuration in place (when the mouse doesn't work at all) in case maybe that will help.
ASKER
Okay, without the Nostromo pad attached and using this configuration:
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "Protocol" "evdev"
Option "Dev Name" "USB Multi-Smart Mouse"
Option "Dev Phys" "usb-*/input0"
Option "Device" "/dev/input/event2"
Option "Buttons" "9"
Option "ZAxisMapping" "4 5"
EndSection
The mouse does not function at all. I hit CTRL-ALT-F5 and logged in so I could check the Xorg.0.log file. What I found was this:
(**) Option "Protocol" "evdev"
(EE) Configured Mouse: Unknown protocol "evdev"
(EE) PreInit failed for input device "Configured Mouse"
(II) UnloadModule: "mouse"
(the complete Xorg.0.log is posted in the attached code section)
I don't know why it's saying evdev is unknown. If I look under Package Manager, I see that "xserver-xorg-input-evdev"
Section "InputDevice"
Identifier "Configured Mouse"
Driver "mouse"
Option "Protocol" "evdev"
Option "Dev Name" "USB Multi-Smart Mouse"
Option "Dev Phys" "usb-*/input0"
Option "Device" "/dev/input/event2"
Option "Buttons" "9"
Option "ZAxisMapping" "4 5"
EndSection
The mouse does not function at all. I hit CTRL-ALT-F5 and logged in so I could check the Xorg.0.log file. What I found was this:
(**) Option "Protocol" "evdev"
(EE) Configured Mouse: Unknown protocol "evdev"
(EE) PreInit failed for input device "Configured Mouse"
(II) UnloadModule: "mouse"
(the complete Xorg.0.log is posted in the attached code section)
I don't know why it's saying evdev is unknown. If I look under Package Manager, I see that "xserver-xorg-input-evdev"
X.Org X Server 1.5.2
Release Date: 10 October 2008
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.24-15-server x86_64 Ubuntu
Current Operating System: Linux decimus 2.6.27-11-generic #1 SMP Wed Apr 1 20:53:41 UTC 2009 x86_64
Build Date: 09 March 2009 01:06:41PM
xorg-server 2:1.5.2-2ubuntu3.1 (buildd@crested.buildd)
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sun Apr 26 16:56:25 2009
(==) Using config file: "/etc/X11/xorg.conf"
(==) No Layout section. Using the first Screen section.
(**) |-->Screen "Default Screen" (0)
(**) | |-->Monitor "Configured Monitor"
(**) | |-->Device "Configured Video Device"
(**) Option "AutoAddDevices" "false"
(**) Not automatically adding devices
(==) Automatically enabling devices
(==) No FontPath specified. Using compiled-in default.
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
Entry deleted from font path.
(==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/75dpi/:unscaled,
/usr/share/fonts/X11/Type1,
/usr/share/fonts/X11/100dpi,
/usr/share/fonts/X11/75dpi,
/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType
(==) ModulePath set to "/usr/lib/xorg/modules"
(==) |-->Input Device "Configured Mouse"
(==) |-->Input Device "Generic Keyboard"
(==) No Layout section. Using the first mouse device.
(==) No Layout section. Using the first keyboard device.
(II) Open ACPI successful (/var/run/acpid.socket)
(II) Loader magic: 0x7b7320
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 4.1
X.Org XInput driver : 2.1
X.Org Server Extension : 1.1
X.Org Font Renderer : 0.6
(II) Loader running on linux
(++) using VT number 7
(--) PCI:*(0@1:0:0) nVidia Corporation unknown chipset (0x0615) rev 162, Mem @ 0xfa000000/16777216, 0xd0000000/268435456, 0xf8000000/33554432, I/O @ 0x0000cc00/128, BIOS @ 0x????????/131072
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[5] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[6] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[7] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[8] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[9] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[10] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[11] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[12] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[13] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[14] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[15] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[16] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[17] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[18] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[19] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[20] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[21] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[22] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[23] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[24] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[25] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[26] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[27] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[28] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[29] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[30] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[31] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[32] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[33] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[34] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[35] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) "extmod" will be loaded by default.
(II) "dbe" will be loaded by default.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "freetype" will be loaded by default.
(II) "record" will be loaded by default.
(II) "dri" will be loaded by default.
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Server Extension
(II) NVIDIA GLX Module 177.82 Tue Nov 4 17:15:47 PST 2008
(II) Loading extension GLX
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "freetype"
(II) Loading /usr/lib/xorg/modules//fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 1.5.2, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.6
(II) Loading font FreeType
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension XFree86-DRI
(II) LoadModule: "nvidia"
(II) Loading /usr/lib/xorg/modules/drivers//nvidia_drv.so
(II) Module nvidia: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Video Driver
(II) LoadModule: "mouse"
(II) Loading /usr/lib/xorg/modules/input//mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 1.4.99.905, module version = 1.3.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.1
(II) LoadModule: "kbd"
(II) Loading /usr/lib/xorg/modules/input//kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
compiled for 1.4.99.905, module version = 1.3.1
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.1
(II) NVIDIA dlloader X Driver 177.82 Tue Nov 4 16:56:15 PST 2008
(II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
(II) Primary Device is: PCI 01@00:00:0
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "wfb"
(II) LoadModule: "wfb"
(II) Loading /usr/lib/xorg/modules//libwfb.so
(II) Module wfb: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(II) resource ranges after probing:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[5] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[6] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[7] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[8] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[9] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[10] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[11] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[12] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[13] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[14] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[15] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[16] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[17] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[18] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[19] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[20] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[21] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[22] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[23] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[24] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[25] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[26] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[27] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[28] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[29] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[30] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[31] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[32] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[33] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[34] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[35] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) NVIDIA(0): Creating default Display subsection in Screen section
"Default Screen" for depth/fbbpp 24/32
(**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
(==) NVIDIA(0): RGB weight 888
(==) NVIDIA(0): Default visual is TrueColor
(==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
(**) NVIDIA(0): Option "NoLogo" "True"
(**) NVIDIA(0): Enabling RENDER acceleration
(II) NVIDIA(0): Support for GLX with the Damage and Composite X extensions is
(II) NVIDIA(0): enabled.
(II) NVIDIA(0): NVIDIA GPU GeForce GTS 150 (G92) at PCI:1:0:0 (GPU-0)
(--) NVIDIA(0): Memory: 1048576 kBytes
(--) NVIDIA(0): VideoBIOS: 62.92.7d.00.11
(II) NVIDIA(0): Detected PCI Express Link width: 16X
(--) NVIDIA(0): Interlaced video modes are supported on this GPU
(--) NVIDIA(0): Connected display device(s) on GeForce GTS 150 at PCI:1:0:0:
(--) NVIDIA(0): Samsung SyncMaster (DFP-1)
(--) NVIDIA(0): Samsung SyncMaster (DFP-1): 330.0 MHz maximum pixel clock
(--) NVIDIA(0): Samsung SyncMaster (DFP-1): Internal Dual Link TMDS
(II) NVIDIA(0): Assigned Display Device: DFP-1
(==) NVIDIA(0):
(==) NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select"
(==) NVIDIA(0): will be used as the requested mode.
(==) NVIDIA(0):
(II) NVIDIA(0): Validated modes:
(II) NVIDIA(0): "nvidia-auto-select"
(II) NVIDIA(0): Virtual screen size determined to be 1680 x 1050
(--) NVIDIA(0): DPI set to (90, 88); computed from "UseEdidDpi" X config
(--) NVIDIA(0): option
(==) NVIDIA(0): Enabling 32-bit ARGB GLX visuals.
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[5] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[6] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[7] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[8] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[9] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[10] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[11] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[12] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[13] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[14] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[15] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[16] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[17] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[18] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[19] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[20] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[21] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[22] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[23] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[24] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[25] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[26] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[27] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[28] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[29] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[30] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[31] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[32] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[33] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[34] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[35] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) NVIDIA(0): Initialized GPU GART.
(II) NVIDIA(0): Setting mode "nvidia-auto-select"
(II) Loading extension NV-GLX
(II) NVIDIA(0): NVIDIA 3D Acceleration Architecture Initialized
(II) NVIDIA(0): Using the NVIDIA 2D acceleration architecture
(==) NVIDIA(0): Backing store disabled
(==) NVIDIA(0): Silken mouse enabled
(II) NVIDIA(0): DPMS enabled
(II) Loading extension NV-CONTROL
(II) Loading extension XINERAMA
(==) RandR enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(II) Initializing extension GLX
(**) Option "Protocol" "evdev"
(EE) Configured Mouse: Unknown protocol "evdev"
(EE) PreInit failed for input device "Configured Mouse"
(II) UnloadModule: "mouse"
(**) Option "CoreKeyboard"
(**) Generic Keyboard: always reports core events
(**) Option "Protocol" "standard"
(**) Generic Keyboard: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Generic Keyboard: XkbRules: "xorg"
(**) Option "XkbModel" "pc105"
(**) Generic Keyboard: XkbModel: "pc105"
(**) Option "XkbLayout" "us"
(**) Generic Keyboard: XkbLayout: "us"
(**) Option "CustomKeycodes" "off"
(**) Generic Keyboard: CustomKeycodes disabled
(II) evaluating device (Generic Keyboard)
(II) XINPUT: Adding extended input device "Generic Keyboard" (type: KEYBOARD)
(II) config/hal: Adding input device Macintosh mouse button emulation
(EE) config/hal: NewInputDeviceRequest failed
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(EE) config/hal: NewInputDeviceRequest failed
(II) config/hal: Adding input device USB Multi-Smart Mouse
(EE) config/hal: NewInputDeviceRequest failed
AUDIT: Sun Apr 26 16:56:27 2009: 6794 X: client 4 rejected from local host ( uid=0 gid=0 pid=6810 )
AUDIT: Sun Apr 26 16:56:39 2009: 6794 X: client 4 rejected from local host ( uid=0 gid=0 pid=6814 )
AUDIT: Sun Apr 26 16:56:51 2009: 6794 X: client 4 rejected from local host ( uid=1000 gid=1000 pid=6816 )
AUDIT: Sun Apr 26 16:56:51 2009: 6794 X: client 4 rejected from local host ( uid=1000 gid=1000 pid=6817 )
AUDIT: Sun Apr 26 16:56:51 2009: 6794 X: client 4 rejected from local host ( uid=1000 gid=1000 pid=6818 )
Are you sure your mouse is handled by evdev ?
Stop display manager and run X -configure to see if it is evdev or mouse.
Stop display manager and run X -configure to see if it is evdev or mouse.
ASKER
I don't know. I just saw that evdev was used in a case that resolved this issue with a similar Trust mouse. I ran X -configure and it generated this:
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/X11/misc
FontPath "/usr/share/fonts/X11/cyri
FontPath "/usr/share/fonts/X11/100d
FontPath "/usr/share/fonts/X11/75dp
FontPath "/usr/share/fonts/X11/Type
FontPath "/usr/share/fonts/X11/100d
FontPath "/usr/share/fonts/X11/75dp
FontPath "/var/lib/defoma/x-ttcidfo
EndSection
Section "Module"
Load "dri"
Load "record"
Load "xtrap"
Load "dbe"
Load "glx"
Load "extmod"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Device"
Identifier "Card0"
Driver "nvidia"
VendorName "nVidia Corporation"
BoardName "Unknown Board"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
So in my /etc/X11/xorg.conf file, I modified the mouse section to look like:
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "Buttons" "9"
Option "ZAxisMapping" "4 5 6 7"
EndSection
When I restart X, the mouse works. I ran xev and tested the buttons... the zoom in/out buttons still do not work. The forward/back buttons (8 and 9) show up in xev, but I can't map them or the zoom in/out buttons in WoW. I also tried the mouse configuration without the Option Buttons line just to see if it made a difference, but the behavior was the same.
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/X11/misc
FontPath "/usr/share/fonts/X11/cyri
FontPath "/usr/share/fonts/X11/100d
FontPath "/usr/share/fonts/X11/75dp
FontPath "/usr/share/fonts/X11/Type
FontPath "/usr/share/fonts/X11/100d
FontPath "/usr/share/fonts/X11/75dp
FontPath "/var/lib/defoma/x-ttcidfo
EndSection
Section "Module"
Load "dri"
Load "record"
Load "xtrap"
Load "dbe"
Load "glx"
Load "extmod"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Device"
Identifier "Card0"
Driver "nvidia"
VendorName "nVidia Corporation"
BoardName "Unknown Board"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
So in my /etc/X11/xorg.conf file, I modified the mouse section to look like:
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "Buttons" "9"
Option "ZAxisMapping" "4 5 6 7"
EndSection
When I restart X, the mouse works. I ran xev and tested the buttons... the zoom in/out buttons still do not work. The forward/back buttons (8 and 9) show up in xev, but I can't map them or the zoom in/out buttons in WoW. I also tried the mouse configuration without the Option Buttons line just to see if it made a difference, but the behavior was the same.
Now post extract from Xorg.0.log relating mouse initialization...
Something is wrong about those extra buttons then.
wth is WoW ?
Something is wrong about those extra buttons then.
wth is WoW ?
ASKER
Sorry about taking a little while to respond. WoW = World of Warcraft. :D
After I rebooted the system (keeping the new configuration in place), the forward/back buttons are working in Firefox. I can't map them to anything in WoW however (do I need to do something so that they pass a specific keystroke? I'm not sure how to do this if so). The zoom buttons do not work at all, still (not in Firefox or WoW). xev still does not recognize them. All of these buttons work properly under Windows though, so I know the buttons are functional.
Attached is the latest Xorg.0.log
After I rebooted the system (keeping the new configuration in place), the forward/back buttons are working in Firefox. I can't map them to anything in WoW however (do I need to do something so that they pass a specific keystroke? I'm not sure how to do this if so). The zoom buttons do not work at all, still (not in Firefox or WoW). xev still does not recognize them. All of these buttons work properly under Windows though, so I know the buttons are functional.
Attached is the latest Xorg.0.log
X.Org X Server 1.5.2
Release Date: 10 October 2008
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.24-15-server x86_64 Ubuntu
Current Operating System: Linux decimus 2.6.27-11-generic #1 SMP Wed Apr 1 20:53:41 UTC 2009 x86_64
Build Date: 09 March 2009 01:06:41PM
xorg-server 2:1.5.2-2ubuntu3.1 (buildd@crested.buildd)
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Wed Apr 29 17:34:09 2009
(==) Using config file: "/etc/X11/xorg.conf"
(==) No Layout section. Using the first Screen section.
(**) |-->Screen "Default Screen" (0)
(**) | |-->Monitor "Configured Monitor"
(**) | |-->Device "Configured Video Device"
(**) Option "AutoAddDevices" "false"
(**) Not automatically adding devices
(==) Automatically enabling devices
(==) No FontPath specified. Using compiled-in default.
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
Entry deleted from font path.
(==) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/75dpi/:unscaled,
/usr/share/fonts/X11/Type1,
/usr/share/fonts/X11/100dpi,
/usr/share/fonts/X11/75dpi,
/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType
(==) ModulePath set to "/usr/lib/xorg/modules"
(==) |-->Input Device "Mouse0"
(==) |-->Input Device "Generic Keyboard"
(==) No Layout section. Using the first core pointer device.
(==) No Layout section. Using the first keyboard device.
(II) Open ACPI successful (/var/run/acpid.socket)
(II) Loader magic: 0x7b7320
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 4.1
X.Org XInput driver : 2.1
X.Org Server Extension : 1.1
X.Org Font Renderer : 0.6
(II) Loader running on linux
(++) using VT number 7
(--) PCI:*(0@1:0:0) nVidia Corporation unknown chipset (0x0615) rev 162, Mem @ 0xfa000000/16777216, 0xd0000000/268435456, 0xf8000000/33554432, I/O @ 0x0000cc00/128, BIOS @ 0x????????/131072
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[5] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[6] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[7] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[8] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[9] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[10] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[11] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[12] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[13] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[14] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[15] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[16] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[17] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[18] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[19] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[20] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[21] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[22] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[23] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[24] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[25] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[26] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[27] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[28] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[29] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[30] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[31] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[32] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[33] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[34] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[35] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) "extmod" will be loaded by default.
(II) "dbe" will be loaded by default.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "freetype" will be loaded by default.
(II) "record" will be loaded by default.
(II) "dri" will be loaded by default.
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Server Extension
(II) NVIDIA GLX Module 177.82 Tue Nov 4 17:15:47 PST 2008
(II) Loading extension GLX
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "freetype"
(II) Loading /usr/lib/xorg/modules//fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 1.5.2, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.6
(II) Loading font FreeType
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension XFree86-DRI
(II) LoadModule: "nvidia"
(II) Loading /usr/lib/xorg/modules/drivers//nvidia_drv.so
(II) Module nvidia: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Video Driver
(II) LoadModule: "mouse"
(II) Loading /usr/lib/xorg/modules/input//mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 1.4.99.905, module version = 1.3.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.1
(II) LoadModule: "kbd"
(II) Loading /usr/lib/xorg/modules/input//kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
compiled for 1.4.99.905, module version = 1.3.1
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.1
(II) NVIDIA dlloader X Driver 177.82 Tue Nov 4 16:56:15 PST 2008
(II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
(II) Primary Device is: PCI 01@00:00:0
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "wfb"
(II) LoadModule: "wfb"
(II) Loading /usr/lib/xorg/modules//libwfb.so
(II) Module wfb: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(II) resource ranges after probing:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[5] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[6] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[7] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[8] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[9] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[10] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[11] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[12] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[13] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[14] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[15] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[16] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[17] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[18] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[19] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[20] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[21] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[22] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[23] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[24] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[25] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[26] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[27] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[28] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[29] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[30] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[31] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[32] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[33] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[34] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[35] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) NVIDIA(0): Creating default Display subsection in Screen section
"Default Screen" for depth/fbbpp 24/32
(**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
(==) NVIDIA(0): RGB weight 888
(==) NVIDIA(0): Default visual is TrueColor
(==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
(**) NVIDIA(0): Option "NoLogo" "True"
(**) NVIDIA(0): Enabling RENDER acceleration
(II) NVIDIA(0): Support for GLX with the Damage and Composite X extensions is
(II) NVIDIA(0): enabled.
(II) NVIDIA(0): NVIDIA GPU GeForce GTS 150 (G92) at PCI:1:0:0 (GPU-0)
(--) NVIDIA(0): Memory: 1048576 kBytes
(--) NVIDIA(0): VideoBIOS: 62.92.7d.00.11
(II) NVIDIA(0): Detected PCI Express Link width: 16X
(--) NVIDIA(0): Interlaced video modes are supported on this GPU
(--) NVIDIA(0): Connected display device(s) on GeForce GTS 150 at PCI:1:0:0:
(--) NVIDIA(0): Samsung SyncMaster (DFP-1)
(--) NVIDIA(0): Samsung SyncMaster (DFP-1): 330.0 MHz maximum pixel clock
(--) NVIDIA(0): Samsung SyncMaster (DFP-1): Internal Dual Link TMDS
(II) NVIDIA(0): Assigned Display Device: DFP-1
(==) NVIDIA(0):
(==) NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select"
(==) NVIDIA(0): will be used as the requested mode.
(==) NVIDIA(0):
(II) NVIDIA(0): Validated modes:
(II) NVIDIA(0): "nvidia-auto-select"
(II) NVIDIA(0): Virtual screen size determined to be 1680 x 1050
(--) NVIDIA(0): DPI set to (90, 88); computed from "UseEdidDpi" X config
(--) NVIDIA(0): option
(==) NVIDIA(0): Enabling 32-bit ARGB GLX visuals.
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[4] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[5] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[6] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[7] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[8] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[9] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[10] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[11] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[12] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[13] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[14] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[15] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[16] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[17] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[18] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[19] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[20] -1 0 0xffffffff - 0xffffffff (0x1) MX[B]
[21] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[22] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[23] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[24] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[25] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[26] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[27] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[28] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[29] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[30] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[31] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[32] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[33] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
[34] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[35] -1 0 0x00000000 - 0x00000000 (0x1) IX[B]
(II) NVIDIA(0): Initialized GPU GART.
(II) NVIDIA(0): Setting mode "nvidia-auto-select"
(II) Loading extension NV-GLX
(II) NVIDIA(0): NVIDIA 3D Acceleration Architecture Initialized
(II) NVIDIA(0): Using the NVIDIA 2D acceleration architecture
(==) NVIDIA(0): Backing store disabled
(==) NVIDIA(0): Silken mouse enabled
(II) NVIDIA(0): DPMS enabled
(II) Loading extension NV-CONTROL
(II) Loading extension XINERAMA
(==) RandR enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(II) Initializing extension GLX
(**) Option "Protocol" "auto"
(**) Option "Device" "/dev/input/mice"
(II) Mouse0: Setting mouse protocol to "ExplorerPS/2"
(**) Mouse0: Device: "/dev/input/mice"
(**) Mouse0: Protocol: "auto"
(**) Option "CorePointer"
(**) Mouse0: always reports core events
(**) Option "Device" "/dev/input/mice"
(**) Option "Buttons" "9"
(==) Mouse0: Emulate3Buttons, Emulate3Timeout: 50
(**) Option "ZAxisMapping" "4 5 6 7"
(**) Mouse0: ZAxisMapping: buttons 4, 5, 6 and 7
(**) Mouse0: Buttons: 13
(**) Mouse0: Sensitivity: 1
(**) Option "CoreKeyboard"
(**) Generic Keyboard: always reports core events
(**) Option "Protocol" "standard"
(**) Generic Keyboard: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Generic Keyboard: XkbRules: "xorg"
(**) Option "XkbModel" "pc105"
(**) Generic Keyboard: XkbModel: "pc105"
(**) Option "XkbLayout" "us"
(**) Generic Keyboard: XkbLayout: "us"
(**) Option "CustomKeycodes" "off"
(**) Generic Keyboard: CustomKeycodes disabled
(II) evaluating device (Mouse0)
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
(II) evaluating device (Generic Keyboard)
(II) XINPUT: Adding extended input device "Generic Keyboard" (type: KEYBOARD)
(II) Mouse0: Setting mouse protocol to "ExplorerPS/2"
(II) Mouse0: ps2EnableDataReporting: succeeded
(II) config/hal: Adding input device Macintosh mouse button emulation
(EE) config/hal: NewInputDeviceRequest failed
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(EE) config/hal: NewInputDeviceRequest failed
(II) config/hal: Adding input device USB Multi-Smart Mouse
(EE) config/hal: NewInputDeviceRequest failed
(II) config/hal: Adding input device Honey Bee Nostromo SpeedPad2
(EE) config/hal: NewInputDeviceRequest failed
(II) config/hal: Adding input device Honey Bee Nostromo SpeedPad2
(EE) config/hal: NewInputDeviceRequest failed
AUDIT: Wed Apr 29 17:34:24 2009: 5675 X: client 4 rejected from local host ( uid=0 gid=0 pid=6416 )
AUDIT: Wed Apr 29 17:34:45 2009: 5675 X: client 4 rejected from local host ( uid=1000 gid=1000 pid=6434 )
AUDIT: Wed Apr 29 17:34:45 2009: 5675 X: client 4 rejected from local host ( uid=1000 gid=1000 pid=6435 )
AUDIT: Wed Apr 29 17:34:45 2009: 5675 X: client 4 rejected from local host ( uid=1000 gid=1000 pid=6436 )
[mi] EQ overflowing. The server is probably stuck in an infinite loop.
[mi] mieqEnequeue: out-of-order valuator event; dropping.
[mi] EQ overflowing. The server is probably stuck in an infinite loop.
[mi] mieqEnequeue: out-of-order valuator event; dropping.
(II) config/hal: Adding input device Pystromo Input Remapper
(EE) config/hal: NewInputDeviceRequest failed
ASKER
Also, to reiterate, the current configuration that I'm using for the mouse is:
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "Buttons" "9"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "Buttons" "9"
Option "ZAxisMapping" "4 5 6 7"
EndSection
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
ASKER
Dumb question... what's the shortcut allocator?
Something like global-keyboard-shortcut-b
Where you can assign key for applications menu, or actions to Win keys
Where you can assign key for applications menu, or actions to Win keys
ASKER
I can't seem to find that. Under System | Preferences, I see Keyboard Shortcuts. It just allows me to assign shortcuts to a list of preset actions. I don't see anything about the mouse button assignments.
http://www.google.nl/search?q=gnome+mouse+button+configuration&hl=en
Looks like hopeless at best... I am with that other desktop environment which takes mouse buttons for shortcuts, and lets copy/paste mouse events from xev. Sorry for being of so little help.
Looks like hopeless at best... I am with that other desktop environment which takes mouse buttons for shortcuts, and lets copy/paste mouse events from xev. Sorry for being of so little help.
ASKER
Thanks for all your help. I'll either have to live with things as the way they are or try a different mouse.