Solved

Mitel 3300 and Procurve 2610 VLANs - Routing

Posted on 2009-05-13
2
1,492 Views
Last Modified: 2012-05-06
Hi,

Let me start by saying I'm not a networking expert. I have been tasked to configure some Procurve 2610's 48 POE, ready for use with a Mitel 3300. I have them setup in a test environment.

>>DCHP Server (to simulate gateway/router)
IP: 192.168.12.254
Giving out IPs in the 192.168.12.0 range.
Connected to Port 2 on Procurve.
DHCP Scope Option 060 used (Mitel Vendor Class), this points it to Mitel 192.168.203.33 with VLAN 2 info.

>>Mitel Switch
IP: 192.168.203.33
Gateway: 192.168.203.2
DHCP service running giving out IPs in the same range.
Scope option 125 set with all the VLAN info.
Connected to Port 1 Procurve.

>>Procurve 2610 Switch
hostname "SWTRWS001"
ip routing
snmp-server community "public" Unrestricted
vlan 1
   name "Data"
   untagged 2-52
   ip address 192.168.12.2 255.255.255.0
   no untagged 1
   exit
vlan 2
   name "Voice"
   untagged 1
   ip address 192.168.203.2 255.255.255.0
   tagged 2-48
   exit
ip route 0.0.0.0 0.0.0.0 192.168.12.254

This is what happens...
Mitel phones get IP from VLAN 1 (192.168.12.254 DHCP server) and release them on instruction of option 060. They then obtain an IP from the Phone Switch using the VLAN 2 (192.168.203.x).
Phones work nicely.
Plug PC in they get IP from VLAN 1 and work.

My Question:
I cannot ping from my PC VLAN 1 to Phone Switch on VLAN 2.
This is a problem as I cannot access the Mitel web interface.

Notes:
I notice that these switch are Lite Layer 3, is this why routing between the VLAN is not working.
I renamed the default vlan and called it Data (VLAN 1).
Is it because I have a MS DHCP Server in the place of a router, so if a real router was used on Port 2 it would do the VLAN routing.

Thanks
0
Comment
Question by:trifastsystems
2 Comments
 
LVL 17

Accepted Solution

by:
jburgaard earned 500 total points
ID: 24403592
If your DHCP server in vlan 1 sets the DGW to 192.168.12.254 , routing must take place here.
If you want to have the Procurve 2610 Switch do the routing (you have enabled) then let DHCP set DGW to the IP of vlan1 on sw.: 192.168.12.2
HTH
 
0
 

Author Comment

by:trifastsystems
ID: 24410793
Thanks that did the trick, makes perfect sense. Got it working in the test environment.
0

Featured Post

Efficient way to get backups off site to Azure

This user guide provides instructions on how to deploy and configure both a StoneFly Scale Out NAS Enterprise Cloud Drive virtual machine and Veeam Cloud Connect in the Microsoft Azure Cloud.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Hi there, This article summarizes what you need if you are going to set up your home or small business Network Attached Storage (NAS) to be accessible from the internet. Of course there are configuration differences based on your NAS or router ma…
Almost all Internet protocol telephones have built-in switches at the back that allow you to connect your personal computer to one port and use the other port to connect your phone to to a Cisco switch.   Why we need to connect the PC to the pho…
Microsoft Active Directory, the widely used IT infrastructure, is known for its high risk of credential theft. The best way to test your Active Directory’s vulnerabilities to pass-the-ticket, pass-the-hash, privilege escalation, and malware attacks …
This video shows how to quickly and easily add an email signature for all users on Exchange 2016. The resulting signature is applied on a server level by Exchange Online. The email signature template has been downloaded from: www.mail-signatures…

840 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question