jdmb001
asked on
slow upload speed isa 2006
I just updated from ISA 2004 to ISA 2006. The install went okay but now I am noticing my upload speed has drop by 1/10. I have disable all filters on the ISA box but have the same problem.
When I check the interface on the Cisco 2811 I see errors coming from the ISA server. When I bypass the ISA server, the speeds are normal.
Download speed is okay.
Currently running 10 Mbps from my ISP.
Any idea on what can be causing this?
When I check the interface on the Cisco 2811 I see errors coming from the ISA server. When I bypass the ISA server, the speeds are normal.
Download speed is okay.
Currently running 10 Mbps from my ISP.
Any idea on what can be causing this?
Keith Alabaster
What errors?
ASKER
Thanks for the reply Keith. Below are the errors I am seeing.
sh int fastethernet0/1
FastEthernet0/1 is up, line protocol is up
Hardware is MV96340 Ethernet, address is 001f.6c95.5141 (bia 001f.6c95.5141)
Description: To ISA
Internet address is 192.168.20.1/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 220/255, txload 6/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 467000 bits/sec, 239 packets/sec
30 second output rate 2366000 bits/sec, 292 packets/sec
88951717 packets input, 1494304903 bytes
Received 1052 broadcasts, 13194222 runts, 0 giants, 0 throttles
13352986 input errors, 158759 CRC, 3 frame, 0 overrun, 2 ignored
0 watchdog
I have already swap the cable between the ISA and the Cisco 2811.
sh int fastethernet0/1
FastEthernet0/1 is up, line protocol is up
Hardware is MV96340 Ethernet, address is 001f.6c95.5141 (bia 001f.6c95.5141)
Description: To ISA
Internet address is 192.168.20.1/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 220/255, txload 6/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 467000 bits/sec, 239 packets/sec
30 second output rate 2366000 bits/sec, 292 packets/sec
88951717 packets input, 1494304903 bytes
Received 1052 broadcasts, 13194222 runts, 0 giants, 0 throttles
13352986 input errors, 158759 CRC, 3 frame, 0 overrun, 2 ignored
0 watchdog
I have already swap the cable between the ISA and the Cisco 2811.
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
ASKER
I have cleared the counter time 16:00, I will clear them tomorrow again after I capture in the sh int.. The NIC was set to auto but I changed it to 100. That jumped the speed from 0.16mb/s to 2 mb/s I wll put etheral on the ISA box. To see what is going on.
Again thanks Keith.
Again thanks Keith.
Welcome :) Sounds like an improvement already
ASKER
Okay back, the problem turn out to be setting the correct speed on the nic card on the ISA server. It was set to Auto but when I changed it to full 100 everything seem to work okay. Thanks for your help.
Excellent :)