International calling

I just set up a Cisco CME voip system for my company, calls are coming in and going out fine except when an international call is placed more than 14 digits there is a busy signal. Does anyone have an idea what would be causeing this.
JBachaAsked:
Who is Participating?
I wear a lot of hats...

"The solutions and answers provided on Experts Exchange have been extremely helpful to me over the last few years. I wear a lot of hats - Developer, Database Administrator, Help Desk, etc., so I know a lot of things but not a lot about one thing. Experts Exchange gives me answers from people who do know a lot about one thing, in a easy to use platform." -Todd S.

dgboydCommented:
What does your voip dial peer look like?
0
JBachaAuthor Commented:
dial-peer voice 9 pots
 translation-profile outgoing dial9
 destination-pattern 9T
 port 0/2/0:23
 forward-digits all
!
dial-peer voice 2 pots
 incoming called-number .
 direct-inward-dial
 port 0/2/0:23
 forward-digits all
!
dial-peer voice 2020 voip
   destination-pattern XXXXXXXX
 translate-outgoing called 2
 session protocol sipv2
 session target ipv4:X.X.X.X
 dtmf-relay sip-notify
 codec g711ulaw
 no vad
!
dial-peer voice 2121 voip
 destination-pattern XXXX
 session protocol sipv2
 session target ipv4:X.X.X.X
 dtmf-relay sip-notify
 codec g711ulaw
 no vad
!
dial-peer voice 9000 voip
 description AA
 destination-pattern XXXXXXXX.
 translate-outgoing called 3
 session protocol sipv2
 session target ipv4:X.X.X.X
 dtmf-relay sip-notify
   codec g711ulaw
 no vad
!
dial-peer voice 9001 voip
 destination-pattern XXXX
 session protocol sipv2
 session target ipv4:X.X.X.X
 dtmf-relay sip-notify
 codec g711ulaw
 no vad
0
dgboydCommented:
Here's a look at an international dial plan that I use:

!
dial-peer voice 5 voip
 description ----------------> International Access
 destination-pattern 9011.T
 session protocol sipv2
 session target ipv4:X.X.X.X
 dtmf-relay sip-notify
 codec g711ulaw
 no vad
!

If it's not the dial peer, then have you checked with the carrier?

Hope this helps.

0
Powerful Yet Easy-to-Use Network Monitoring

Identify excessive bandwidth utilization or unexpected application traffic with SolarWinds Bandwidth Analyzer Pack.

lrmooreCommented:
Do you have any COR configuration?

This dial-peer should match any number, even overseas. Have you tried debug dialpeer to see if it hitting this dialpeer?

dial-peer voice 9 pots
 translation-profile outgoing dial9
 destination-pattern 9T
 port 0/2/0:23
 forward-digits all
0
ged125Commented:
I see that you are forwarding the 9 on your dial-peer, is this a Centrex line?  Do you know if it is provisioned for International dialing?  If it is an analog line, can you hook an analog set to it and test the same number?
0

Experts Exchange Solution brought to you by

Your issues matter to us.

Facing a tech roadblock? Get the help and guidance you need from experienced professionals who care. Ask your question anytime, anywhere, with no hassle.

Start your 7-day free trial
JBachaAuthor Commented:
Thank you for your responces, I found a resoloution to the issue. to be able to dial the all the international numbers. I created this dial-peer

dial-peer voice 9011 pots
 translation-profile outgoing dial9011
 destination-pattern 9011T
 port 0/2/0:23
 forward-digits all
 prefix 011


and inforced this rule in it
voice translation-rule 2
rule 1 /^9011\(.*\)/ /\1/ type any unknown plan any unknown

with some adjustment I can most likely apply this to the first outgoing dial-peer and get rid of this one. But this works so I will leave it for now.


0
It's more than this solution.Get answers and train to solve all your tech problems - anytime, anywhere.Try it for free Edge Out The Competitionfor your dream job with proven skills and certifications.Get started today Stand Outas the employee with proven skills.Start learning today for free Move Your Career Forwardwith certification training in the latest technologies.Start your trial today
Voice Over IP

From novice to tech pro — start learning today.