JimNirv
asked on
No Encapsulation on C2621
I am trying to setup either ISL or 802.1Q but cannot find the image I need. I tried c2600-is-mz.123-26.bin, c2600-i-mz.123-26.bin and c2600-j1s3-mz.123-26.bin.
I am running the following:
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.3(3g), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Thu 20-May-04 20:57 by kellythw
Image text-base: 0x80008098, data-base: 0x80C999C0
ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)
NS-CR2621-NY01 uptime is 1 hour, 17 minutes
System returned to ROM by reload
System image file is "flash:c2600-i-mz.123-3g.b in"
cisco 2621 (MPC860) processor (revision 0x200) with 56320K/9216K bytes of memory
.
Processor board ID JAD0518047R (722937158)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Any help would be greatly appreciated.
I am running the following:
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.3(3g), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Thu 20-May-04 20:57 by kellythw
Image text-base: 0x80008098, data-base: 0x80C999C0
ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)
NS-CR2621-NY01 uptime is 1 hour, 17 minutes
System returned to ROM by reload
System image file is "flash:c2600-i-mz.123-3g.b
cisco 2621 (MPC860) processor (revision 0x200) with 56320K/9216K bytes of memory
.
Processor board ID JAD0518047R (722937158)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Any help would be greatly appreciated.
SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
ASKER
Ah, ok. That makes sense, will another 16 MB of flash do the trick or do I need more?
32MB is the required amount of Flash to support that image and probably the max that router supports.
Take a look at this doc. Looks like you'll also need to get a new boot ROM for the router.
http://www.cisco.com/en/US/docs/routers/access/2600/hardware/installation/notes/2600mem.html#wp93177
http://www.cisco.com/en/US/docs/routers/access/2600/hardware/installation/notes/2600mem.html#wp93177
ASKER
Thanks for the information everyone, I will try upgrading.
Sure thing. You may want to evaluate the cost of the flash memory and boot ROM chip versus buy a 2621XM router off eBay :)
ASKER