Solved

SBS 2008

Posted on 2009-07-03
7
1,123 Views
Last Modified: 2012-05-07
Hi

I have a problem, i tried to run the routing and remote access wizard to enable vpn access and it failed now the routing and remote access service is in a stopping state, i have rebooted but its still in a stopping state how can i resolve this?

Where is the log file so i can start and see whats wrong?

Any one any ideas
0
Comment
Question by:nostrasystems
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 4
  • 3
7 Comments
 

Author Comment

by:nostrasystems
ID: 24771794
i found the log file vpncw in program files windows small business server logs
0
 

Author Comment

by:nostrasystems
ID: 24771822
---------------------------------------------------------
[13664] 090703.103956.9110: General: Initializing...C:\Program Files\Windows Small Business Server\Bin\VPNCW.exe
[13664] 090703.104001.5248: Wizard: WizardChainEngine Next Clicked: Last page, so the wizard isdone, closing wizard frame and returning
[11108] 090703.104002.0280: AdminTME: AdminDataLink Running Task: CommitterSequenceTask
[11108] 090703.104114.9305: CoreNet: Exception Microsoft.WindowsServerSolutions.CoreNetworking.CNetException:
HR: 0

[11108] 090703.104114.9480: Exception:
---------------------------------------
An exception of type 'Type: Microsoft.WindowsServerSolutions.CoreNetworking.CNetException, CNetManagement, Version=6.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35' has occurred.
Timestamp: 07/03/2009 10:41:14
Message: The 'RemoteAccess' service is running, but MprAdminIsServiceRunning says that RRAS is not ready yet.
Stack:    at Microsoft.WindowsServerSolutions.CoreNetworking.CNetRRAS.StartRRAS()
         at Microsoft.WindowsServerSolutions.Networking.Wizards.VPNCWizard.TaskConfigureVPN.Run(ITaskDataLink dataLink)
---------------------------------------
An exception of type 'Type: System.ServiceProcess.TimeoutException, System.ServiceProcess, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a' has occurred.
Timestamp: 07/03/2009 10:41:14
Message: RRAS
Stack: No stack trace is available.

[11108] 090703.104114.9559: AdminTME: Status: TaskId = Networking.Wizards.VPNCWizard.ConfigureVPN, RootTaskId = Networking.Wizards.VPNCWizard.ConfigureVPN, Success: False, Warning: False, Continue: False, Message: Virtual private networking is not set up. Ensure that Routing and Remote Access is installed and running, and then rerun this wizard.
[13664] 090703.104115.0037: AdminTME: Committer: Completed called
[13664] 090703.104115.0037: AdminTME: Committer: Task was cancelled.
[13664] 090703.104115.0291: AdminTME: Committer: Committer Completed.
0
 
LVL 39

Expert Comment

by:Philip Elder
ID: 24772973
Use the VPN wizard under the Connectivity tab found under the Network tab in the SBS Console.

That is the proper method for enabling the VPN setup in SBS 2008.

Make sure that the firewall/router/gateway appliance has been set to allow 1723 PPTP and it's secondary GRE protocol (gets enabled by default when 1723 is port forwarded) is forwarded to the SBS 2008 box.

Philip
0
MIM Survival Guide for Service Desk Managers

Major incidents can send mastered service desk processes into disorder. Systems and tools produce the data needed to resolve these incidents, but your challenge is getting that information to the right people fast. Check out the Survival Guide and begin bringing order to chaos.

 

Author Comment

by:nostrasystems
ID: 24777397
I did all of this did u not read my post ???????
0
 
LVL 39

Expert Comment

by:Philip Elder
ID: 24787545
Traditionally, RRAS wizard is accessed via the RRAS console. The SBS VPN Wizard is a part of the SBS Console under the network connectivity tab.

They are two different wizards.

Philip
0
 
LVL 39

Expert Comment

by:Philip Elder
ID: 24787661
And yes, I did have a look at your second log a bit more thoroughly and now realize that you were running the correct wizard. So, my apologies for not looking closer.

What is the status of the RRAS service under Services.msc?

Philip
0
 

Accepted Solution

by:
nostrasystems earned 0 total points
ID: 24788502
no prob i fixed the issue it was an issue with IP V6 not being enabled so reenabled it and now the wizard runs fine.
0

Featured Post

[Webinar] Code, Load, and Grow

Managing multiple websites, servers, applications, and security on a daily basis? Join us for a webinar on May 25th to learn how to simplify administration and management of virtual hosts for IT admins, create a secure environment, and deploy code more effectively and frequently.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

I’m often asked about newer and larger USB drives connected to SBS2008 and 2011 failing Windows Server Backup vs the older USB drives not failing. As disk space continues to grow and drive technology change SBS2008 and some SBS2011 end up with the f…
I work for a company that primarily works with small businesses as their outsourced IT vendor. As such the majority of these customers utilize some version of Small Business Server. Due to the economics of running a small business, many of these cus…
Finding and deleting duplicate (picture) files can be a time consuming task. My wife and I, our three kids and their families all share one dilemma: Managing our pictures. Between desktops, laptops, phones, tablets, and cameras; over the last decade…
This video shows how to use Hyena, from SystemTools Software, to update 100 user accounts from an external text file. View in 1080p for best video quality.

739 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question