Solved

How do I configure Cisco 2811 as a voice gateway?

Posted on 2009-07-07
10
6,088 Views
Last Modified: 2013-12-27
I need help configuring voice gateway for my new CCM7.0 with At&t PRI. I  have procured Cisco 2811 for the same. Here are the details:
1x Cisco2811-V/K9
1x PVDM2-16U32
1xVIC2-2FXO
1xVWIC2-1MFT-T1/E1

Can someone please help me configure the same? Thanks!!

0
Comment
Question by:umeshjagannatha
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 6
  • 4
10 Comments
 
LVL 10

Expert Comment

by:voipman
ID: 24807428
What kind of gateway in CCM do you want to set up?
0
 

Author Comment

by:umeshjagannatha
ID: 24807521
I am planning to configure SIP. I have CCM7 and Unity 7.0 and at&t is my local PRI provider.
0
 
LVL 10

Expert Comment

by:voipman
ID: 24807539
ok do you need help with the ccm gateway or just the config of the 2811?
0
DevOps Toolchain Recommendations

Read this Gartner Research Note and discover how your IT organization can automate and optimize DevOps processes using a toolchain architecture.

 

Author Comment

by:umeshjagannatha
ID: 24807606
I am using 2811 only as my voice gateway so I guess will need to configure accordingly. Thanks!
0
 

Author Comment

by:umeshjagannatha
ID: 24808225
Please see the current configuration of the router.
VGWYCONFIG.txt
0
 
LVL 10

Accepted Solution

by:
voipman earned 125 total points
ID: 24808253
Ok so you already have the gateway configured in CCM 7.0 ?  This should get you going with the router.


isdn switch-type primary-ni
voice-card 0
no dspfarm
ip domain-name xxxxxxx
no ip bootp server
ip name-server  xxxxxx
!
voice class codec 1
codec preference 1 g729r8
codec preference 2 g711ulaw
codec preference 3 g711alaw
!
interface fastethernet0/0
ip address xxxxxxxxxxx
duplex full
speed 100
no cdp enable
no shutdown
call rsvp-sync
Bind control source-interface xxxxxx
Bind media source-interface xxxxxxx
call rsvp-sync
!
interface serial  0/0/0
bandwidth 1536
service-module t1 timeslot 1-24
service-module t1 framing esf
service-module t1 linecode b8zs
tx-ring-limit 1
no ip address
no shutdown
no fair-queue
ip classless
!
no ip http server
no ip http secure-server
!
voice service voip
sip
rel1xx disable
Card type T1 0 1
controller T1 0/1/0
framing  esf
clock source  line
linecode  b8zs
cablelength  short 133
pri-group timeslot 1-24
!
!
no fair-queue
no cdp enable
!
!
voice-port  0/0/0:23
no non-linear
busyout action shutdown
busyout monitor Serial0/0/0
!
!
control-plane
dial-peer  voice 400 voip
description outbound
destination-pattern xxxx
incoming-called number xxxx
rtp  payload-type nte 98
voice-class  codec 1
session protocol  sipv2
session target sip-server
dtmf-relay  rtp-nte
no vad
!
!
dial-peer  voice 101 pots
destination-pattern xxxx
incoming-called number xxxx
direct-inward-dial
port 0/1/0:23
!
sip-ua

retry  invite 2
retry  cancel 2
retry  bye 2
sip-server  dns:FQDN or IP
g729-annexb override


0
 

Author Comment

by:umeshjagannatha
ID: 24808470
Really appreciate your help. I have a couple more question about the configuration. Please see the attached file.
VGWY.txt
0
 
LVL 10

Expert Comment

by:voipman
ID: 24809209
Do you have a sip trunk set up in CCM ?


sip-server  dns:FQDN or IP This will be the IP of the dns or the fully qualified domain name

ip domain-name xxxxxxx this is your company domain

ip address xxxxxxxxxxx (Will this be my 2811 router IP?) yes

ip name-server  xxxxxx (Will this be my DNS server name?) yes

Bind control source-interface xxxxxx this is your ethernet int ip address
Bind media source-interface xxxxxxx this is your ethernet int ip address
0
 

Author Comment

by:umeshjagannatha
ID: 24809258
No. I haven't setup SIP trunk in the CCM yet. This is for my new site, I haven't configured the Call Managers at this moment. At this moment I'm making sure I have all the correct configuration ready before deploying it next week.
0
 

Author Closing Comment

by:umeshjagannatha
ID: 31600887
Really appreciate all your Help. Thanks again! -DJ
0

Featured Post

Independent Software Vendors: We Want Your Opinion

We value your feedback.

Take our survey and automatically be enter to win anyone of the following:
Yeti Cooler, Amazon eGift Card, and Movie eGift Card!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Home wifi - Does it matter what router? 9 94
Where is running-config located at in ASR9K? 3 39
Voice vlan and access vlan 2 59
Routing Issue 26 67
I recently purchased a Bluetooth headset called the Music Jogger (model BSH10). The control buttons on it look like this: One of my goals is to use it as the microphone and speakers for Skype calls. In that respect, it works well. However, I …
If your business is like most, chances are you still need to maintain a fax infrastructure for your staff. It’s hard to believe that a communication technology that was thriving in the mid-80s could still be an essential part of your team’s modern I…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

734 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question