Solved

Adding a second WAN subnet to a SonicWall

Posted on 2009-07-13
3
985 Views
Last Modified: 2012-05-07
I have a sonicwall 2040pro with Enhanced OS.  We are in the process of upgrading our T1 from 1.5Mb to a bonded 6 Mb.  We are keeping our old IP range and they have added a second IP range to our new router.  My question is how to properly configure the WAN interface on the SonicWall.  I have read a similar question here but it was relating to the LAN side.  I've configured the new subnet as a "Secondary WAN Subnet" and assigned it to the WAN zone.  The other article mentioned adding it to the LAN subnets group (in my case I added it to the WAN zone but I don't see any way to add any address objects to either the LAN or WAN subnets group in the sonicwall).  These groups are greyed out and not modifyable according to the Sonicwall documentation.  I've also added a route  as follows:  any  "WAN secondary subnet"  any  0.0.0.0  X1

Any help is much appreciated!!
0
Comment
Question by:kevmartin01
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
3 Comments
 
LVL 8

Accepted Solution

by:
dosdet2 earned 500 total points
ID: 24844292
I don't know your sonicwall model, but it you have maintenance with sonicwall, they will walk you through step by step. Just a thought.
0
 

Author Comment

by:kevmartin01
ID: 24844544
We do have a support contract.  I wasn't aware they would assist with configuration changes.  I look at that in the future.  I added one of the new IP addresses and assigned it as "Secondary WAN IP" and assigned it to X1 as well as adding the new network as "Secondary WAN Subnet" and left the route listed above.  We have cut over to the new T1 and the connection is there.  I can only see my original subnet thru www.cmyip.com but that doesn't mean they are not working.  I will test outside access inbound tonight with the new IP's and report back.  Hopefully this experience will help someone.  I'm awarding you the points.

Thanks all!
0
 

Author Closing Comment

by:kevmartin01
ID: 31602934
Thanks again for the suggestion!
0

Featured Post

Free Tool: Path Explorer

An intuitive utility to help find the CSS path to UI elements on a webpage. These paths are used frequently in a variety of front-end development and QA automation tasks.

One of a set of tools we're offering as a way of saying thank you for being a part of the community.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

In the hope of saving someone else's sanity... About a year ago we bought a Cisco 1921 router with two ADSL/VDSL EHWIC cards to load balance local network traffic over the two broadband lines we have, but we couldn't get the routing to work consi…
Before I go to far, let's explain HA (High Availability) and why you should consider it.  High availability is the mechanism used to provide redundancy to any service at the same site and appears as a single service to the users of that service.  As…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

718 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question