Deek
asked on
Routing 3 networks with CISCO 3560 Layer 3 Switch
Here is what my "scratch pad" routing came out to... is this correct if I want to be able to access any network from any other network? (NOTE I am utilizing the CAT 3560 SW with VLANs to do the routing between the nets).
ASA 5510 FW 10.1.1.1 --> Default Gateway for all .1 Nodes
Add Route: 10.1.3.0 10.1.3.10 255.255.255.0
Add Route: 192.168.195.0 10.1.3.10 255.255.255.0
Add Route: 192.168.194.0 10.1.3.10 255.255.255.0
CAT 3560 SW 10.1.1.5
NOTE: Allow routing between all VLANs utilizing Layer 3 Switch Routing
VLAN1 (Data) 10.1.1.10
Add Route: 10.1.3.0 10.1.3.10 255.255.255.0
Add Route: 192.168.195.0 192.168.195.10 255.255.255.0
Add Route: 192.168.194.0 192.168.195.10 255.255.255.0
VLAN2 (VoIP) 10.1.3.10
Add Route: 10.1.1.0 10.1.1.10 255.255.255.0
Add Route: 192.168.195.0 192.168.195.10 255.255.255.0
Add Route: 192.168.194.0 192.168.195.10 255.255.255.0
VLAN3 (Data) 192.168.195.10
Add Route: 10.1.1.0 10.1.1.10 255.255.255.0
Add Route: 10.1.3.0 10.1.3.10 255.255.255.0
Add Route: 192.168.194.0 192.168.195.1 255.255.255.0
PIX 515E FW 192.168.195.1 --> Default Gateway for all .195 Nodes
Add Route: 10.1.1.0 192.168.195.10 255.255.255.0
Add Route: 10.1.3.0 192.168.195.10 255.255.255.0
Route Note: 192.168.194.0/24 routed through existing P2P VPN Tunnel.
CAT 2811 RTR 10.1.3.1 --> Default Gateway for all .3 Nodes
Add Route: 10.1.1.0 10.1.3.10 255.255.255.0
Add Route: 192.168.195.0 10.1.3.10 255.255.255.0
Add Route: 192.168.194.0 10.1.3.10 255.255.255.0
MCS 7800 VoIP 10.1.3.2
Thanks!
ASA 5510 FW 10.1.1.1 --> Default Gateway for all .1 Nodes
Add Route: 10.1.3.0 10.1.3.10 255.255.255.0
Add Route: 192.168.195.0 10.1.3.10 255.255.255.0
Add Route: 192.168.194.0 10.1.3.10 255.255.255.0
CAT 3560 SW 10.1.1.5
NOTE: Allow routing between all VLANs utilizing Layer 3 Switch Routing
VLAN1 (Data) 10.1.1.10
Add Route: 10.1.3.0 10.1.3.10 255.255.255.0
Add Route: 192.168.195.0 192.168.195.10 255.255.255.0
Add Route: 192.168.194.0 192.168.195.10 255.255.255.0
VLAN2 (VoIP) 10.1.3.10
Add Route: 10.1.1.0 10.1.1.10 255.255.255.0
Add Route: 192.168.195.0 192.168.195.10 255.255.255.0
Add Route: 192.168.194.0 192.168.195.10 255.255.255.0
VLAN3 (Data) 192.168.195.10
Add Route: 10.1.1.0 10.1.1.10 255.255.255.0
Add Route: 10.1.3.0 10.1.3.10 255.255.255.0
Add Route: 192.168.194.0 192.168.195.1 255.255.255.0
PIX 515E FW 192.168.195.1 --> Default Gateway for all .195 Nodes
Add Route: 10.1.1.0 192.168.195.10 255.255.255.0
Add Route: 10.1.3.0 192.168.195.10 255.255.255.0
Route Note: 192.168.194.0/24 routed through existing P2P VPN Tunnel.
CAT 2811 RTR 10.1.3.1 --> Default Gateway for all .3 Nodes
Add Route: 10.1.1.0 10.1.3.10 255.255.255.0
Add Route: 192.168.195.0 10.1.3.10 255.255.255.0
Add Route: 192.168.194.0 10.1.3.10 255.255.255.0
MCS 7800 VoIP 10.1.3.2
Thanks!
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.