?
Solved

I wan to make calls between site A to B. A is 2600 Router with 4 port FXS Card and B is 3600 with FXO and connected to EPABX by e1. How do I Configure both the routers. Pls provide configurations ste

Posted on 2010-01-11
6
Medium Priority
?
379 Views
Last Modified: 2013-12-27
Site A is 2600 router with 4 port FXS Card. Site B is a 3600 Router with FXO cards. 3600 is connected to EPABX.
I want to make calls outbound from Site A to Site B by directly connecting the phone to FXS Card.

Please provide the configuration steps nedded in both 3600 and 2600.

Here is the Show Version of both :
SITE A:

------------------ show version ------------------

Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IS-M), Version 12.2(3), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2001 by cisco Systems, Inc.
Compiled Wed 18-Jul-01 17:36 by pwade
Image text-base: 0x80008088, data-base: 0x8103F020

ROM: System Bootstrap, Version 12.2(6r),  RELEASE SOFTWARE (fc1)

GOARG01 uptime is 17 weeks, 6 days, 11 hours, 12 minutes
System returned to ROM by power-on
System image file is "flash:c2600-is-mz.122-3.bin"

cisco 2620 (MPC860) processor (revision 0x00) with 45056K/4096K bytes of memory.
Processor board ID JAD06230GM5 (3176786734)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
1 ISDN Basic Rate interface(s)
4 Voice FXS interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102


SITE B:

------------------ show version ------------------

Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-IS-M), Version 12.2(40), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Thu 12-Oct-06 17:43 by pwade
Image text-base: 0x60008930, data-base: 0x6113C000

ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

INDRO01 uptime is 3 weeks, 3 days, 6 hours, 37 minutes
System returned to ROM by power-on
System image file is "flash:c3640-is-mz.122-40.bin"

cisco 3640 (R4700) processor (revision 0x00) with 58368K/7168K bytes of memory.
Processor board ID 28724109
R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
Primary Rate ISDN software, Version 1.1.
Basic Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
4 Serial(sync/async) network interface(s)
8 Low-speed serial(sync/async) network interface(s)
4 ISDN Basic Rate interface(s)
1 Channelized E1/PRI port(s)
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

Please provide detailes configuration steps or best practice scenarios.
0
Comment
Question by:Manishkumarnavar
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 4
  • 2
6 Comments
 
LVL 34

Accepted Solution

by:
Istvan Kalmar earned 1500 total points
ID: 26291606
Hi,

You need to configure connection plar:

http://www.cisco.com/en/US/tech/tk1077/technologies_configuration_example09186a00800942a5.shtml

Best regrds,
Istvan
0
 

Author Comment

by:Manishkumarnavar
ID: 26321796
In this doccument I dont understand meaning of using
dial-peer voice 1 pots
destination-pattern 1000
port 1/0:1
!
dial-peer voice 2 pots
destination-pattern 1001
port 1/0:2  


though connection plar is 2000 and 2001 .

 I want to  call using 2114. Please suggest.


0
 
LVL 34

Expert Comment

by:Istvan Kalmar
ID: 26321927
voice-port 1/0:1
 connection plar 2414
 
!--- This command starts a PLAR switched
!--- VoIP call that uses digits (2000)
 !--- to match a VoIP dial-peer when the voice-port 1/0:1 goes off-hook.


!


!
dial-peer voice 1 pots
 destination-pattern 1000
 port 1/0:1
!
dial-peer voice 2 pots
 destination-pattern 1001
 port 1/0:2
dial-peer voice 3 voip
 destination-pattern 200.

 !--- Matches the connection plar strings
!--- 2000 and 2001.

dtmf-relay h245-alphanumeric
 session target ipv4:x.x.x.x

0
Get MongoDB database support online, now!

At Percona’s web store you can order your MongoDB database support needs in minutes. No hassles, no fuss, just pick and click. Pay online with a credit card. Handle your MongoDB database support now!

 

Author Comment

by:Manishkumarnavar
ID: 26357745
Hi,
Is there any relation betgween Connection PLAR configured at site A and destination pattern  configured at site B ?
I only want to call from B to A,  do I require to configure voice Pots in B ?
I would appreciate if you can give me a configuration example where calling should be done from B to A only. Please provide the configuration steps in both B and A router. I have FXS in B where directly phones are connected and  FXO in router A, integrated with EPABX .
0
 

Author Comment

by:Manishkumarnavar
ID: 26378202
Hi, Can anyone help me out resolve above query ?
0
 

Author Closing Comment

by:Manishkumarnavar
ID: 31675738
Issue is resolved using PLAR
0

Featured Post

Windows Server 2016: All you need to know

Learn about Hyper-V features that increase functionality and usability of Microsoft Windows Server 2016. Also, throughout this eBook, you’ll find some basic PowerShell examples that will help you leverage the scripts in your environments!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Creating an OSPF network that automatically (dynamically) reroutes network traffic over other connections to prevent network downtime.
This article will show how Aten was able to supply easy management and control for Artear's video walls and wide range display configurations of their newsroom.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Suggested Courses
Course of the Month9 days, 1 hour left to enroll

764 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question