leo11
asked on
cisco 3640 setup interface
dear all
i got a cisco 3640 not configured ,it have default configuration , so when i try to configure it i don't show the interface ethernet0/0
i followed the system configuration dialog to complete the configuration and i arrived to configure SNMP network management then i seen this dialog:enter interface name used to connect to the management network from the above interface summary:
need help
thank you
i got a cisco 3640 not configured ,it have default configuration , so when i try to configure it i don't show the interface ethernet0/0
i followed the system configuration dialog to complete the configuration and i arrived to configure SNMP network management then i seen this dialog:enter interface name used to connect to the management network from the above interface summary:
need help
thank you
Istvan Kalmar
please show us the blank config
ASKER
Current configuration : 378 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
no service dhcp
!
hostname Router
!
!
memory-size iomem 15
ip subnet-zero
!
!
!
ip audit notify log
ip audit po max-events 100
!
call rsvp-sync
!
!
!
!
!
!
!
!
ip classless
no ip http server
!
!
!
dial-peer cor custom
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
!
end
Router#
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
no service dhcp
!
hostname Router
!
!
memory-size iomem 15
ip subnet-zero
!
!
!
ip audit notify log
ip audit po max-events 100
!
call rsvp-sync
!
!
!
!
!
!
!
!
ip classless
no ip http server
!
!
!
dial-peer cor custom
!
!
!
!
!
line con 0
line aux 0
line vty 0 4
!
end
Router#
ASKER
System flash directory:
File Length Name/status
1 14862356 c3640-jk9o3s-mz.122-46a.bi
[14862420 bytes used, 18167720 available, 33030140 total]
32768K bytes of processor board System flash (Read/Write)
Router#sh interfaces summary
*: interface is up
IHQ: pkts in input hold queue IQD: pkts dropped from input queue
OHQ: pkts in output hold queue OQD: pkts dropped from output queue
RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)
TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)
TRTL: throttle count
Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL
--------------------------
NOTE:No separate counters are maintained for subinterfaces
Hence Details of subinterface are not shown
Router#
File Length Name/status
1 14862356 c3640-jk9o3s-mz.122-46a.bi
[14862420 bytes used, 18167720 available, 33030140 total]
32768K bytes of processor board System flash (Read/Write)
Router#sh interfaces summary
*: interface is up
IHQ: pkts in input hold queue IQD: pkts dropped from input queue
OHQ: pkts in output hold queue OQD: pkts dropped from output queue
RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)
TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)
TRTL: throttle count
Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL
--------------------------
NOTE:No separate counters are maintained for subinterfaces
Hence Details of subinterface are not shown
Router#
it seems that the router not recognized the network module
ASKER
i don't install the module now
I noticed something that maybe the router cisco 3640 have 2 ethernet port for use console only?
I noticed something that maybe the router cisco 3640 have 2 ethernet port for use console only?
ASKER
any help please?
if you not installing network module you not have ETH interface
3600-29423.gif
3600-29423.gif
ASKER
when i install the module interfaces i can't show any interface because the system image file is : c3640-jk9o3s-mz-122-46a.bi
what type of NM card do you have?
ASKER
i have nm esw 16
It is not supported by 3640
ASKER
what should be i do ? what the nm is supported by 3640?
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.