Cisco switch 4510 problem

Hi All


Please I have problem in our Cisco switch 4500 serious. the switch contain couple of Cisco Catalyst 4510 Series Supervisor Engine V. when power on its try to boot but fail and went to monitor mode. did that mean the IOS was damage and if damage from where I can get one

I attached the screen for booting

Any idea will help

Regards

**********************************************************                                                           
 *                                                        *                                                           
 * Welcome to Rom Monitor for  WS-X4516 System.           *                                                           
 * Copyright (c) 1999-2003 by Cisco Systems, Inc.         *                                                           
 * All rights reserved.                                   *                                                           
 *                                                        *                                                           
 **********************************************************                                                           

 Rom Monitor Program Version 12.1(20r)EW1                                         
 Supervisor: WS-X4516  Chassis: WS-C4510                                        
 Hardware Revisions - Board: 3.7 CPLD: 4 Dagobah: 95                                                    


 MAC Address  : 00-0a-b7-03-f3-68                                 
 IP Address   : 10.1.1.56                         
 Netmask      : 255.255.255.0                             
 Gateway      : 10.1.1.1                        
 TftpServer   : 10.1.1.1                        
 Main Memory  : 512 MBytes                          



 ***** The system will autoboot in 5 seconds *****                                                  


 Type control-C to prevent autobooting.                                       
 . . . . .          

 ******** The system will autoboot now ********                                               


 config-register = 0x2102                         
 Autobooting using BOOT variable specified file.....                                                    

 Current BOOT file is --- bootflash:cat4500-entservicesk9-mz.122-46.SG.bin                                                                          
 boot: can not load "bootflash:cat4500-entservicesk9-mz.122-46.SG.bin"                                                                      


 The switch will automatically reboot now...                                            
rommon 1 >          






 **********************************************************                                                           
 *                                                        *                                                           
 * Welcome to Rom Monitor for  WS-X4516 System.           *                                                           
 * Copyright (c) 1999-2003 by Cisco Systems, Inc.         *                                                           
 * All rights reserved.                                   *                                                           
 *                                                        *                                                           
 **********************************************************                                                           

 Rom Monitor Program Version 12.1(20r)EW1                                         
 Supervisor: WS-X4516  Chassis: WS-C4510                                        
 Hardware Revisions - Board: 3.7 CPLD: 4 Dagobah: 95                                                    


 MAC Address  : 00-0a-b7-03-f3-68                                 
 IP Address   : 10.1.1.56                         
 Netmask      : 255.255.255.0                             
 Gateway      : 10.1.1.1                        
 TftpServer   : 10.1.1.1                        
 Main Memory  : 512 MBytes                          



 ***** The system will autoboot in 5 seconds *****                                                  


 Type control-C to prevent autobooting.                                       
 . . . . .          

 ******** The system will autoboot now ********                                               


 config-register = 0x2102                         
 Autobooting using BOOT variable specified file.....                                                    

 Current BOOT file is --- bootflash:cat4500-entservicesk9-mz.122-46.SG.bin                                                                          
 boot: can not load "bootflash:cat4500-entservicesk9-mz.122-46.SG.bin"                                                                      


 The switch will automatically reboot now...                                            
rommon 1 >          






 **********************************************************                                                           
 *                                                        *                                                           
 * Welcome to Rom Monitor for  WS-X4516 System.                                                      
 * Copyright (c) 1999-2003 by Cisco Systems, Inc.         *                                                           
 * All rights reserved.                                   *                                                           
 *                                                        *                                                           
 **********************************************************                                                           

 Rom Monitor Program Version 12.1(20r)EW1                                         
 Supervisor: WS-X4516  Chassis: WS-C4510                                        
 Hardware Revisions - Board: 3.7 CPLD: 4 Dagobah: 95                                                    


 MAC Address  : 00-0a-b7-03-f3-68                                 
 IP Address   : 10.1.1.56                         
 Netmask      : 255.255.255.0                             
 Gateway      : 10.1.1.1                        
 TftpServer   : 10.1.1.1                        
 Main Memory  : 512 MBytes                          



 ***** The system will autoboot in 5 seconds *****                                                  


 Type control-C to prevent autobooting.                                       
 . . . . .          

 ******** The system will autoboot now ********                                               


 config-register = 0x2102                         
 Autobooting using BOOT variable specified file.....                                                    

 Current BOOT file is --- bootflash:cat4500-entservicesk9-mz.122-46.SG.bin                                                                          
 boot: can not load "bootflash:cat4500-entservicesk9-mz.122-46.SG.bin"                                                                      


 The switch will automatically reboot now...                                            
rommon 1 >          






 **************************************************                                                  
 *                                                        *                                                           
 * Welcome to Rom Monitor for  WS-X4516 System.           *                                                           
 * Copyright (c) 1999-2003 by Cisco Systems, Inc.         *                                                           
 * All rights reserved.                                   *                                                           
 *                                                        *                                                           
 **********************************************************                                                           

 Rom Monitor Program Version 12.1(20r)EW1                                         
 Supervisor: WS-X4516  Chassis: WS-C4510                                        
 Hardware Revisions - Board: 3.7 CPLD: 4 Dagobah: 95                                                    


 MAC Address  : 00-                  
 IP Address   : 10.1.1.56                         
 Netmask      : 255.255.255.0                             
 Gateway      : 10.1.1.1
 TftpServer   : 10.1.1.1
 Main Memory  : 512 MBytes



 ***** The system will autoboot in 5 seconds *****


 Type control-C to prevent autobooting.
 . . . . .

 ******** The system will autoboot now ********


 config-register = 0x2102
 Autobooting using BOOT variable specified file.....

 Could not find a valid file in BOOT environment variable.
 BOOT variable can be set from IOS. To find currently set
 Rom Monitor variables, please type 'set' command.

 For help on choosing a boot method,  type 'confreg' command.
rommon 1 >

Open in new window

nasemabdullaaAsked:
Who is Participating?
I wear a lot of hats...

"The solutions and answers provided on Experts Exchange have been extremely helpful to me over the last few years. I wear a lot of hats - Developer, Database Administrator, Help Desk, etc., so I know a lot of things but not a lot about one thing. Experts Exchange gives me answers from people who do know a lot about one thing, in a easy to use platform." -Todd S.

Don JohnstonInstructorCommented:
It's either corrupt or not in flash at all.

Check and make sure you've got the correct filename.
0
atlas_shudderedSr. Network EngineerCommented:
One of either two issues here.  First could be that your config-register is set to the wrong address space and therefore not able find and booth the image noted.  If not noted in documentation, I am not sure how your would go about recovering this.  Second would be that your image has either been deleted or somehow become corrupt.  In either case, you will need to load a new copy.  If you do not have an archival copy of the CatOS image, then you will need to download a copy from cisco support.  To do this you will need a current support contract and registered CCO ID with cisco.
0

Experts Exchange Solution brought to you by

Your issues matter to us.

Facing a tech roadblock? Get the help and guidance you need from experienced professionals who care. Ask your question anytime, anywhere, with no hassle.

Start your 7-day free trial
mikebernhardtCommented:
From the rommon prompt, type "dir bootflash" and see what you get. that is where the switch is looking for its image.
0
It's more than this solution.Get answers and train to solve all your tech problems - anytime, anywhere.Try it for free Edge Out The Competitionfor your dream job with proven skills and certifications.Get started today Stand Outas the employee with proven skills.Start learning today for free Move Your Career Forwardwith certification training in the latest technologies.Start your trial today
Switches / Hubs

From novice to tech pro — start learning today.