Cisco Aironet GUI

My client has a Cisco Aironet 802.11a/b/g AP that I want to get the GUI up and running on.  What is the command to enable the GUI?

Thanks,

MAG
LVL 17
Marius GunnerudSenior Systems EngineerAsked:
Who is Participating?
I wear a lot of hats...

"The solutions and answers provided on Experts Exchange have been extremely helpful to me over the last few years. I wear a lot of hats - Developer, Database Administrator, Help Desk, etc., so I know a lot of things but not a lot about one thing. Experts Exchange gives me answers from people who do know a lot about one thing, in a easy to use platform." -Todd S.

HodepineCommented:
If it's an IOS based AP it's the following command in global config:

ip http server
0
Marius GunnerudSenior Systems EngineerAuthor Commented:
Thanks will test it out
0
HodepineCommented:
You'll probably need the follwing to login through the web interface:

username yournamehere priv 15 password yourpasshere
ip http authentication local
0
The Ultimate Tool Kit for Technolgy Solution Provi

Broken down into practical pointers and step-by-step instructions, the IT Service Excellence Tool Kit delivers expert advice for technology solution providers. Get your free copy for valuable how-to assets including sample agreements, checklists, flowcharts, and more!

Marius GunnerudSenior Systems EngineerAuthor Commented:
hmm the ip http server and ip http sercure-server doesn't work.  Does a port need to be opened?
0
Marius GunnerudSenior Systems EngineerAuthor Commented:
Ok, I can't seem to get it working I have attached the configuration.  Could you have a look and tell me if there is anything that needs to be changed so the GUI will work.

Thanks.

MAG
Aironet-config.txt
0
HodepineCommented:
As far as I can see it should work with https:// like it is.

I logged on to a 1240 at a customer and the config there is:

ip http server
no ip http secure-server

You're in global config mode when entering the command?

And you can connect to the device by IP? You're using telnet or console now?

If so, try this command and post the output:

Show ip http server all
0
Marius GunnerudSenior Systems EngineerAuthor Commented:
I was connected via console.  Will try the show command you suggested but will not be back at that client until late next week.  Will let you know how it goes.

MAG
0
HodepineCommented:
Ok, as long as you were connected by console, it might be an IP related issue as well. Are you able to ping the device?
0

Experts Exchange Solution brought to you by

Your issues matter to us.

Facing a tech roadblock? Get the help and guidance you need from experienced professionals who care. Ask your question anytime, anywhere, with no hassle.

Start your 7-day free trial
Marius GunnerudSenior Systems EngineerAuthor Commented:
I am unable to ping the device!  hmmm Though IP and gateway are configured on the device.  What might be wrong?
0
HodepineCommented:
Check cabling and vlan configuration on the switch if any.
0
Marius GunnerudSenior Systems EngineerAuthor Commented:
Cabling is fine and there is no vlan.

0
HodepineCommented:
Can you do a "show ip interface brief"?
0
Marius GunnerudSenior Systems EngineerAuthor Commented:
I will be going back to the client this afternoon and will update you with the ip int brief output then.
0
Marius GunnerudSenior Systems EngineerAuthor Commented:
There was an issue with the IP and Default Gateway. Thanks for your help.
0
Marius GunnerudSenior Systems EngineerAuthor Commented:
Changing the IP address solved the issue.
0
It's more than this solution.Get answers and train to solve all your tech problems - anytime, anywhere.Try it for free Edge Out The Competitionfor your dream job with proven skills and certifications.Get started today Stand Outas the employee with proven skills.Start learning today for free Move Your Career Forwardwith certification training in the latest technologies.Start your trial today
Wireless Hardware

From novice to tech pro — start learning today.