dcitdir
asked on
Use Cisco 3750 switch with HP Procurve 2626
My main network consists of Cisco 3750 switches with VLANS. The HP Procurve swithc is offsite connected via fiber. I need to setup the hp switch to have the same vlans as the cisco switches so I can setup voip phones and a wireless access link. I thought I was on the right track but just cannot get the wireless link to work and haven't even tried the phones yet. Here is my cisco vlan configs
interface Vlan20
description DATA
ip address 192.168.3.253 255.255.252.0 secondary
ip address 192.168.10.254 255.255.255.0 secondary
ip address 192.168.3.254 255.255.252.0
ip helper-address 192.168.0.1
no ip mroute-cache
interface Vlan30
description PHONE
ip address 192.168.7.254 255.255.252.0
ip access-group 130 in
ip helper-address 192.168.0.1
no ip mroute-cache
interface Vlan200
description WIRELESS NETWORK
no ip address
no ip mroute-cache
I then need port3 on the hp switch to be setup with the following vlans:
interface FastEthernet5/0/48
description NETWORK
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 20,30,200
switchport mode trunk
no cdp enable
I know the cisco programming but am struggling with the programming of the hp switch since it is different. Anyone able to help me with some commands?
interface Vlan20
description DATA
ip address 192.168.3.253 255.255.252.0 secondary
ip address 192.168.10.254 255.255.255.0 secondary
ip address 192.168.3.254 255.255.252.0
ip helper-address 192.168.0.1
no ip mroute-cache
interface Vlan30
description PHONE
ip address 192.168.7.254 255.255.252.0
ip access-group 130 in
ip helper-address 192.168.0.1
no ip mroute-cache
interface Vlan200
description WIRELESS NETWORK
no ip address
no ip mroute-cache
I then need port3 on the hp switch to be setup with the following vlans:
interface FastEthernet5/0/48
description NETWORK
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 20,30,200
switchport mode trunk
no cdp enable
I know the cisco programming but am struggling with the programming of the hp switch since it is different. Anyone able to help me with some commands?
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
I am not sure what you mean: 'it will not take any ip addresses I put in for the vlans'
What do you do / expect / actual result ???
If any one of the vlans on cisco side are native, it should be UNtagged on HP port 3 to match and be carried via the trunk.
What do you do / expect / actual result ???
If any one of the vlans on cisco side are native, it should be UNtagged on HP port 3 to match and be carried via the trunk.
ASKER
I get an error message that the ip address is already in use.
ASKER
It would look something like this:
vlan 20
name "VLAN20"
untagged ----- Whatever device ports are in this VLAN
tagged 3
ip address 192.168.3.254 255.255.252.0
exit
vlan 30
name "VLAN30"
untagged ----- Whatever device ports are in this VLAN
tagged 3
ip address 192.168.7.254 255.255.252.0
exit
vlan 200
name "VLAN200"
untagged ----- Whatever device ports are in this VLAN
tagged 3
ip address X.X.X.X 255.255.255.0
exit
I guess I am confused what IP address I should put in. Here is what I tried.
vlan 20
name "VLAN20"
untagged ----- Whatever device ports are in this VLAN
tagged 3
ip address 192.168.3.254 255.255.252.0
exit
vlan 30
name "VLAN30"
untagged ----- Whatever device ports are in this VLAN
tagged 3
ip address 192.168.7.254 255.255.252.0
exit
vlan 200
name "VLAN200"
untagged ----- Whatever device ports are in this VLAN
tagged 3
ip address X.X.X.X 255.255.255.0
exit
I guess I am confused what IP address I should put in. Here is what I tried.
You can't use those addresses because they are already in use on the Cisco. If you want IP on these VLANs on the HP they need to be in the same subnet as the Cisco VLAN addresses but with a different host address.
You don't have to put IP on the VLANs in the HP if you just want to use Layer 2 to get across the link.
You don't have to put IP on the VLANs in the HP if you just want to use Layer 2 to get across the link.
ASKER