Configuration for Cisco Aironet 1200 Series
Hello,
I have 3 Cisco Aironet 1200 series APs here with 2 radios, and I'd like to set them all up to be able to access the LAN via one radio and internet only (for clients/vendors) with Radio 2. Vlans are already configured correctly.
I'd like to have WPA(2) for both Radios, DHCP provided by the APs and broadcasting their SSIDs.
Does anyone have any templates that would accomplish this?
I have 3 Cisco Aironet 1200 series APs here with 2 radios, and I'd like to set them all up to be able to access the LAN via one radio and internet only (for clients/vendors) with Radio 2. Vlans are already configured correctly.
I'd like to have WPA(2) for both Radios, DHCP provided by the APs and broadcasting their SSIDs.
Does anyone have any templates that would accomplish this?
SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
Did you config the port on your switch that the AP is connected to for trunking? You need to do this so that it can access two VLAN from a single port.
Since I have configured only two VLANs, VLAN1 is my corporate network and VLAN300 is the Guest network for the AP.
Looks like you have three vlans. YOu will need to configure switchport access to trunk between three vlans.
now for the commands that aren't working, is your AP set to run in autonomous mode or to use a Wireless Lan Controller?
Since I have configured only two VLANs, VLAN1 is my corporate network and VLAN300 is the Guest network for the AP.
Looks like you have three vlans. YOu will need to configure switchport access to trunk between three vlans.
now for the commands that aren't working, is your AP set to run in autonomous mode or to use a Wireless Lan Controller?
ASKER
Yes, I've configured my switchport for trunking to use all required VLANs.
In my case, the AP is sitting on a hardware VLAN (21) but the switchport is configured for access to both the hardware and users VLAN (30).
How can I see if its running in autonomous mode or to use a wireless lan controller?
In my case, the AP is sitting on a hardware VLAN (21) but the switchport is configured for access to both the hardware and users VLAN (30).
How can I see if its running in autonomous mode or to use a wireless lan controller?
do a "sho ver" and post the results.
ASKER
Cisco Internetwork Operating System Software
IOS (tm) C1200 Software (C1200-K9W7-M), Version 12.2(13)JA1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Fri 14-Nov-03 15:09 by kellmill
Image text-base: 0x00003000, data-base: 0x0053CD5C
ROM: Bootstrap program is C1200 boot loader
BOOTLDR: C1200 Boot Loader (C1200-BOOT-M) Version 12.2(8)JA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
ap uptime is 1 minute
System returned to ROM by power-on
System image file is "flash:/c1200-k9w7-mx.122-
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco AIR-AP1220-IOS-UPGRD (PowerPC405GP) processor with 14326K/2048K bytes of memory.
Processor board ID FHK0729K1J2
PowerPC405GP CPU at 196Mhz, revision number 0x00C4
Last reset from power-on
Bridging software.
1 FastEthernet/IEEE 802.3 interface(s)
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:0D:65:43:68:60
Part Number : 0-0000-00
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FHK0729K1J2
Top Assembly Part Number : 000-00000-00
Top Assembly Serial Number :
Top Revision Number :
Product/Model Number : AIR-AP1220-IOS-UPGRD
Configuration register is 0xF
IOS (tm) C1200 Software (C1200-K9W7-M), Version 12.2(13)JA1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Fri 14-Nov-03 15:09 by kellmill
Image text-base: 0x00003000, data-base: 0x0053CD5C
ROM: Bootstrap program is C1200 boot loader
BOOTLDR: C1200 Boot Loader (C1200-BOOT-M) Version 12.2(8)JA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
ap uptime is 1 minute
System returned to ROM by power-on
System image file is "flash:/c1200-k9w7-mx.122-
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco AIR-AP1220-IOS-UPGRD (PowerPC405GP) processor with 14326K/2048K bytes of memory.
Processor board ID FHK0729K1J2
PowerPC405GP CPU at 196Mhz, revision number 0x00C4
Last reset from power-on
Bridging software.
1 FastEthernet/IEEE 802.3 interface(s)
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:0D:65:43:68:60
Part Number : 0-0000-00
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FHK0729K1J2
Top Assembly Part Number : 000-00000-00
Top Assembly Serial Number :
Top Revision Number :
Product/Model Number : AIR-AP1220-IOS-UPGRD
Configuration register is 0xF
ASKER
Any update to this?
Sorry been busy :) get back to you shorly
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
ASKER
My apologies for not taking a look at this. I will be doing so this upcoming week.
ASKER
The solutions here were not exact. After using a combination of parts from here and research on other sites, I managed to figure it out.
ASKER
Okay, I've set up a RADIUS/IAS server.
Just to be clear, in the config you provided in that link, I'm a bit confused by what numbers you're using for what VLANs, and confused regarding the bridge groups.
Now, I see that your VLAN 1 is your Private and VLAN 300 is your public. But when I replace those numbers with my VLANs, doesn't seem to work.
Woudl you be able to plug in the numbers for me and repaste the config?
VLAN my AP is sitting on: 21
VLAN used for user access: 30
VLAN used for Public access: 33
Also, I'm not able to run the "dot11" and "mbssid" commands.