configure aironet 1140
I just configured a cisco wireless controller 2100 and connected 2 aironet 1140 to it.
I can see the 2 AP on the controller but I don't see any wireless signal.
It shows on the AP box that the radios are turned off. I then tried connecting to the AP via the IP I found on the controller but that doesn't work. I then access it via CLI but I can't enter privilege mode.
I can enter the exec mode but conf t doesn't work.
on the AP it keeps reloading this:
*Jun 11 17:54:10.604: %LWAPP-3-CLIENTERRORLOG: Set Transport Address: no more AP
manager IP addresses remain
examining image...
Loading file /c1140...
*Jun 11 17:54:10.612: %LWAPP-5-CHANGED: CAPWAP changed state to JOIN
*Jun 11 17:57:20.598: %LWAPP-5-CHANGED: CAPWAP changed state to IMAGE
transport input ssh
^
% Invalid input detected at '^' marker.
RSSI IDB null
RSSI IDB null
%Error opening lwapp:/c1140 (Protocol error)
archive download: takes 6 seconds
*Jun 11 17:57:26.598: %LWAPP-3-CLIENTERRORLOG: Retransmission count for type (I
MAGE_DATA) exceeded more than max(1)
*Jun 11 17:57:26.598: %LWAPP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Jun 11 17:57:26.598: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Jun 11 17:57:26.608: %LWAPP-3-CLIENTERRORLOG: not receive read response(3)
*Jun 11 17:57:26.612: lwapp_image_proc: unable to open tar file
I tried resetting the AP by pressing the mode button and power the AP but that doesn't seems to be working either.
I am stuck here and any help will be greatly appreciated
I can see the 2 AP on the controller but I don't see any wireless signal.
It shows on the AP box that the radios are turned off. I then tried connecting to the AP via the IP I found on the controller but that doesn't work. I then access it via CLI but I can't enter privilege mode.
I can enter the exec mode but conf t doesn't work.
on the AP it keeps reloading this:
*Jun 11 17:54:10.604: %LWAPP-3-CLIENTERRORLOG: Set Transport Address: no more AP
manager IP addresses remain
examining image...
Loading file /c1140...
*Jun 11 17:54:10.612: %LWAPP-5-CHANGED: CAPWAP changed state to JOIN
*Jun 11 17:57:20.598: %LWAPP-5-CHANGED: CAPWAP changed state to IMAGE
transport input ssh
^
% Invalid input detected at '^' marker.
RSSI IDB null
RSSI IDB null
%Error opening lwapp:/c1140 (Protocol error)
archive download: takes 6 seconds
*Jun 11 17:57:26.598: %LWAPP-3-CLIENTERRORLOG: Retransmission count for type (I
MAGE_DATA) exceeded more than max(1)
*Jun 11 17:57:26.598: %LWAPP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Jun 11 17:57:26.598: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Jun 11 17:57:26.608: %LWAPP-3-CLIENTERRORLOG: not receive read response(3)
*Jun 11 17:57:26.612: lwapp_image_proc: unable to open tar file
I tried resetting the AP by pressing the mode button and power the AP but that doesn't seems to be working either.
I am stuck here and any help will be greatly appreciated
Hi, it seems the APs not seeing the wlan controller AP manager leg! Please set APs and AP mgmt leg same VLAN
ASKER
IOS is 12.3(8)
I set one of the AP on the power injector and the other one on the POE but still same issue.
@Ikalmar I agree with you but they are on the same subnet. they are getting an IP from DHCP but I can't ping them so I am thinking this is the issue. My problem is that I can change any configuration on the AP from the CLI as I can't access the privilege mode :-/
I set one of the AP on the power injector and the other one on the POE but still same issue.
@Ikalmar I agree with you but they are on the same subnet. they are getting an IP from DHCP but I can't ping them so I am thinking this is the issue. My problem is that I can change any configuration on the AP from the CLI as I can't access the privilege mode :-/
Hi did you confugured correctly the dhcp options of wlc?
ASKER
I used our dhcp server and I believe it works since the AP gets an IP. I might have missed an option on the WLC but they are communicating with each other because if I changed the AP name then the change will reflect on the controller side
thanks
thanks
Did you configured option 43?
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808714fe.shtml
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808714fe.shtml
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
Can you get to the power injector options of the ap's on from the controller? I have to select power injector check box before I can enable the radios.