Solved

how to check if the router ( SHDSL interface ) working properly ?

Posted on 2010-08-14
8
641 Views
Last Modified: 2012-05-10

Dear Experts

I Have Router Cisco 3854 -MB and this router have following Cards :
- HWIC -2shdsl
- NM-16AM - V2 Modem / Quantity 4 cards /

and i have these question please answer me clearly

Q1 : HWIC -2 shdsl cards ( have LED L0 = Green On and LED L1 OFF ) is this mean
the Card ( L0 ) configured properly and working .

Q2 : how to know if this cards connected to MPLS.VPN network

Q3 : i tried to check the configuration using SDM V25 but i noticed it is not supported all Cards installed , what you prefer ( GUI programs ) to check the router configuration .

Thanks



dialup-router-confg
0
Comment
Question by:Muhammed-Rummaneh
  • 4
  • 4
8 Comments
 
LVL 4

Expert Comment

by:Valutus
ID: 33435712
what does "show interfaces" produce?
0
 
LVL 4

Author Comment

by:Muhammed-Rummaneh
ID: 33435718

For more information about  Q1 check this picture

Thanks
1.jpg
0
 
LVL 4

Author Comment

by:Muhammed-Rummaneh
ID: 33435725

Dear Valutus
Now i can't answer you , tomorrow i will check it ( show interface command )
and will you give  an answer

thanks
0
PRTG Network Monitor: Intuitive Network Monitoring

Network Monitoring is essential to ensure that computer systems and network devices are running. Use PRTG to monitor LANs, servers, websites, applications and devices, bandwidth, virtual environments, remote systems, IoT, and many more. PRTG is easy to set up & use.

 
LVL 4

Expert Comment

by:Valutus
ID: 33435735
Excellent.  The show Interfaces command will provide you with full details as to the status of the connection.  Your specifically interested in the status of the ATM0/0/0 and ATM0/0/1 interfaces.
0
 
LVL 4

Author Comment

by:Muhammed-Rummaneh
ID: 33435760

ok ...how i can notice from Show interface command if the interface is connected to

Public network ( mpls.vpn )

do you have Skybe

Thanks
0
 
LVL 4

Expert Comment

by:Valutus
ID: 33435765
Paste the output of the show Interfaces command here.
0
 
LVL 4

Accepted Solution

by:
Muhammed-Rummaneh earned 0 total points
ID: 33496920

Thanks All

I Solved My problem by my Self
 
Q1 : to know if card is connected to public network ( L0 must be Green ) this mean the SHDSL interface is connected and working

Q2 : if you want to know if the card is connected to MPLS.VPN network
after configuring the card issue command ( Show IP route )

you will see ( New Line ) at routing table ...connected to dialer interface this mean the card connected to MPLS.VPN

Q3 : I used  SDM after upgrading IOS


Thanks
0
 
LVL 4

Expert Comment

by:Valutus
ID: 33499568
Had you posted the information I requested it would have been trivial to determine the status of your connection...  I'm glad you got it sorted out in the end.
0

Featured Post

Easy, flexible multimedia distribution & control

Coming soon!  Ideal for large-scale A/V applications, ATEN's VM3200 Modular Matrix Switch is an all-in-one solution that simplifies video wall integration. Easily customize display layouts to see what you want, how you want it in 4k.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
best recommendation for a hardware diagnostic tool 7 96
AWS Design\Cisco Meraki 4 34
Public IP Address - Subnet 4 35
Receiving wifi on an underground station 22 96
In the hope of saving someone else's sanity... About a year ago we bought a Cisco 1921 router with two ADSL/VDSL EHWIC cards to load balance local network traffic over the two broadband lines we have, but we couldn't get the routing to work consi…
Quality of Service (QoS) options are nearly endless when it comes to networks today. This article is merely one example of how it can be handled in a hub-n-spoke design using a 3-tier configuration.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Windows 10 is mostly good. However the one thing that annoys me is how many clicks you have to do to dial a VPN connection. You have to go to settings from the start menu, (2 clicks), Network and Internet (1 click), Click VPN (another click) then fi…

860 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question