Solved

LACP Nortel Layer2-3 GbE and Cisco 3650

Posted on 2010-08-14
29
3,207 Views
Last Modified: 2013-11-09
We are trying to enable LACP between a Nortel Layer2-3 GbE and a Cisco 3650.

We are passing traffic accross Cisco port 36 but not the other two (35 and 37).

Have attempted removal of Spanning Tree and the active/passive change from the Nortel side with no luck.

Below is the current conditions and settings:
Error:
Gi0/35      Suspended            LACP      32768      null
Gi0/36      In port-channel      LACP      32768      null
Gi0/37      stand-alone            LACP      32768      null

Nortel side:
 EXT1 active  32768  38  
 EXT2 active  32768  38  
 EXT3 active  32768  38  
Spanning Tree Group 1
  EXT1    128    128    on  
  EXT2    128    128    on  
  EXT3    128    128    on  

On the Cisco 3650:
We have Etherchannel setup on Group 38 with ports 35, 36, 37.

0
Comment
Question by:LSolt
  • 17
  • 12
29 Comments
 
LVL 4

Expert Comment

by:cdowdy
ID: 33436457
Are you allowing Vlan 1 as native (untagged) across the trunk? I believe LACP protocol packets are always sent on vlan 1 and must arrive untagged.
0
 

Author Comment

by:LSolt
ID: 33436479
Yes, we are using VLan 1 in Spanning Tree Group 1 with all of the switch ports assigned.
0
 

Author Comment

by:LSolt
ID: 33436504
Here is the config from the nortel.
Nortel-Config-1.JPG
0
 
LVL 4

Expert Comment

by:cdowdy
ID: 33436518
would you be able to share the cisco interface and port channel configs?
0
 

Author Comment

by:LSolt
ID: 33436573
Here are the cisco configs
Cisco-Config-1.PNG
0
 

Author Comment

by:LSolt
ID: 33436580
0
 
LVL 4

Expert Comment

by:cdowdy
ID: 33436646
Hmm.. from the gui, it looks simple enough, but have no experience with the gui so I might still suspect a subtle config issue. From the CLI can you issue:

#sh run int G0/35

#sh run int G0/36

#sh run int G0/37

#sh run int Po38

and post the outputs?
0
 
LVL 4

Expert Comment

by:cdowdy
ID: 33436716
also, in the Alteon CLI you can go to:

/info/l2/lacp/dump

for more complete LACP info on the Nortel side.. This could tell us something as well
0
 
LVL 4

Expert Comment

by:cdowdy
ID: 33436749
http://www.bladenetwork.net/userfiles/file/PDFs/IBM_GbE_L2-3_Command_Ref.pdf

From the above Document, page 242 shows LACP config for the Nortel. You may have already done this, but be sure LACP is mode active on all of the ports you are aggregating, and that they are using the same admin key. The admin key is locally significant, so no need to match it on the cisco device.
0
 

Author Comment

by:LSolt
ID: 33436752
Looking for the console cable. Telnet not working.
0
 

Author Comment

by:LSolt
ID: 33436758
Thanks that was the first thing I confirmed.
0
 

Author Comment

by:LSolt
ID: 33437055
Port 35 -->

Bottom-Switch#sh int G0/35
GigabitEthernet0/35 is up, line protocol is up (connected)
  Hardware is Gigabit Ethernet, address is a40c.c399.d7a3 (bia a40c.c399.d7a3)
  Description: LACP Blade 1-2
  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:15, output 00:00:07, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 255000 bits/sec, 126 packets/sec
  5 minute output rate 206000 bits/sec, 103 packets/sec
     73039 packets input, 20029949 bytes, 0 no buffer
     Received 4517 broadcasts (0 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 670 multicast, 0 pause input
     0 input packets with dribble condition detected
     57113 packets output, 15058272 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out
Bottom-Switch#
0
 

Author Comment

by:LSolt
ID: 33437060
Port 36 -->

Bottom-Switch#sh int G0/36
GigabitEthernet0/36 is up, line protocol is down (suspended)
  Hardware is Gigabit Ethernet, address is a40c.c399.d7a4 (bia a40c.c399.d7a4)
  Description: LACP Blade 1-1
  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:01, output 00:00:04, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     555 packets input, 46848 bytes, 0 no buffer
     Received 555 broadcasts (0 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 555 multicast, 0 pause input
     0 input packets with dribble condition detected
     203 packets output, 23534 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out
Bottom-Switch#
0
 

Author Comment

by:LSolt
ID: 33437064
Port 37 -->
Bottom-Switch#sh int G0/37
GigabitEthernet0/37 is up, line protocol is up (connected)
  Hardware is Gigabit Ethernet, address is a40c.c399.d7a5 (bia a40c.c399.d7a5)
  Description: LACP Blade 1-3
  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output 00:00:07, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 5000 bits/sec, 8 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     7535 packets input, 699290 bytes, 0 no buffer
     Received 7004 broadcasts (0 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 951 multicast, 0 pause input
     0 input packets with dribble condition detected
     183 packets output, 20092 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out
Bottom-Switch#
0
VMware Disaster Recovery and Data Protection

In this expert guide, you’ll learn about the components of a Modern Data Center. You will use cases for the value-added capabilities of Veeam®, including combining backup and replication for VMware disaster recovery and using replication for data center migration.

 
LVL 4

Expert Comment

by:cdowdy
ID: 33437065
ok, once you can console in and get the config output, we can be more sure of the cisco side. If all looks good, we can do
#conf t
#logg console
#end
#debug lacp all
and take a look at the protocol exchange...
0
 

Author Comment

by:LSolt
ID: 33437075
Here is the Run configs for the three ports and

Bottom-Switch#sh run int Po38
Building configuration...

Current configuration : 32 bytes
!
interface Port-channel38
end

Bottom-Switch#sh run int G0/37
Building configuration...

Current configuration : 95 bytes
!
interface GigabitEthernet0/37
description LACP Blade 1-3
channel-group 38 mode active
end

Bottom-Switch#sh run int G0/36
Building configuration...

Current configuration : 95 bytes
!
interface GigabitEthernet0/36
description LACP Blade 1-1
channel-group 38 mode active
end

Bottom-Switch#sh run int G0/35
Building configuration...

Current configuration : 95 bytes
!
interface GigabitEthernet0/35
description LACP Blade 1-2
channel-group 38 mode active
end

Bottom-Switch#
0
 
LVL 4

Expert Comment

by:cdowdy
ID: 33437076
cool, still need:

#sh run int G0/35

#sh run int G0/36

#sh run int G0/37

#sh run int Po38
0
 
LVL 4

Expert Comment

by:cdowdy
ID: 33437079
oops.. there they are.. ok one sec
0
 

Author Comment

by:LSolt
ID: 33437087
LACP Debugging is on.
0
 
LVL 4

Expert Comment

by:cdowdy
ID: 33437097
one more:

#sh etherchannel port-channel
0
 

Author Comment

by:LSolt
ID: 33437123
Here is the output from the debugging:
009150: 00:28:36:     lacp_mux Gi0/35 - mux: during state COLLECTING_DISTRIBUTIN

G, got event 5(in_sync) (ignored)

009151: 00:28:37: LACP :lacp_bugpak: Receive LACP-PDU packet via Gi0/36

009152: 00:28:37: LACP : packet size: 124

009153: 00:28:37: LACP: pdu: subtype: 1, version: 1

009154: 00:28:37: LACP: Act: tlv:1, tlv-len:20, key:0x11, p-pri:0x8000, p:0x11,

p-state:0xD,

s-pri:0x8000, s-mac:0017.efb3.a200

009155: 00:28:37: LACP: Part: tlv:2, tlv-len:20, key:0x26, p-pri:0x8000, p:0x24,

 p-state:0x85,

s-pri:0x8000, s-mac:a40c.c399.d780

009156: 00:28:37: LACP: col-tlv:3, col-tlv-len:16, col-max-d:0x8000

009157: 00:28:37: LACP: term-tlv:0 termr-tlv-len:0

009158: 00:28:37: LACP: Gi0/36 LACP packet received, processing

009159: 00:28:37:     lacp_rx Gi0/36 - rx: during state CURRENT, got event 5(rec

v_lacpdu)

009160: 00:28:37: @@@ lacp_rx Gi0/36 - rx: CURRENT -> CURRENT

009161: 00:28:37: LACP: Gi0/36 lacp_action_rx_current entered

009162: 00:28:37: LACP: recordPDU Gi0/36 LACP PDU Rcvd. Partners oper state is h

ex D

009163: 00:28:37: LACP: recordPDU Gi0/36 Partner in sync and aggregating

009164: 00:28:37: LACP: Gi0/36 Partners oper state is hex D

009165: 00:28:37: LACP: timer lacp_c_l(Gi0/36) started with interval 90000.

009166: 00:28:37: LACP: Gi0/36 LAG_PARTNER_UP.

009167: 00:28:37: LACP: Gi0/36 LAG unchanged

009168: 00:28:37: LACP: Gi0/36 cannot create an aggregator

009169: 00:28:39: LACP: lacp_p(Gi0/37) timer stopped

009170: 00:28:39: LACP: lacp_p(Gi0/37) expired

009171: 00:28:39:     lacp_ptx Gi0/37 - ptx: during state SLOW_PERIODIC, got eve

nt 3(pt_expired)

009172: 00:28:39: @@@ lacp_ptx Gi0/37 - ptx: SLOW_PERIODIC -> PERIODIC_TX

009173: 00:28:39: LACP: Gi0/37 lacp_action_ptx_slow_periodic_exit entered

009174: 00:28:39: LACP: lacp_p(Gi0/37) timer stopped

009175: 00:28:39: LACP: Gi0/37 lacp_action_ptx_periodic_tx entered

009176: 00:28:39: LACP: timer lacp_t(Gi0/37) started with interval 1000.

009177: 00:28:39: LACP: lacp_send_lacpdu: (Gi0/37) About to send the 110 LACPDU

009178: 00:28:39: LACP :lacp_bugpak: Send LACP-PDU packet via Gi0/37

009179: 00:28:39: LACP : packet size: 124

009180: 00:28:39: LACP: pdu: subtype: 1, version: 1

009181: 00:28:39: LACP: Act: tlv:1, tlv-len:20, key:0x26, p-pri:0x8000, p:0x25,

p-state:0x7D,

s-pri:0x8000, s-mac:a40c.c399.d780

009182: 00:28:39: LACP: Part: tlv:2, tlv-len:20, key:0x0, p-pri:0x0, p:0x0, p-st

ate:0x0,

s-pri:0x0, s-mac:0000.0000.0000

009183: 00:28:39: LACP: col-tlv:3, col-tlv-len:16, col-max-d:0x8000

009184: 00:28:39: LACP: term-tlv:0 termr-tlv-len:0

009185: 00:28:39: LACP: lacp_write: LACP 124 bytes out Gi0/37

009186: 00:28:39:     lacp_ptx Gi0/37 - ptx: during state PERIODIC_TX, got event

 2(long_timeout)

009187: 00:28:39: @@@ lacp_ptx Gi0/37 - ptx: PERIODIC_TX -> SLOW_PERIODIC

009188: 00:28:39: LACP: Gi0/37 lacp_action_ptx_slow_periodic entered

009189: 00:28:39: LACP: timer lacp_p_s(Gi0/37) started with interval 30000.

009190: 00:28:39: LACP :lacp_bugpak: Receive LACP-PDU packet via Gi0/21

009191: 00:28:39: LACP : packet size: 124

009192: 00:28:39: LACP: pdu: subtype: 1, version: 1

009193: 00:28:39: LACP: Act: tlv:1, tlv-len:20, key:0x3, p-pri:0x8000, p:0x16, p

-state:0x3D,

s-pri:0x8000, s-mac:0024.f9ea.8000

009194: 00:28:39: LACP: Part: tlv:2, tlv-len:20, key:0x1, p-pri:0x8000, p:0x15,

p-state:0x3D,

s-pri:0x8000, s-mac:a40c.c399.d780

009195: 00:28:39: LACP: col-tlv:3, col-tlv-len:16, col-max-d:0x8000

009196: 00:28:39: LACP: term-tlv:0 termr-tlv-len:0

009197: 00:28:39: LACP: Gi0/21 LACP packet received, processing

009198: 00:28:39:     lacp_rx Gi0/21 - rx: during state CURRENT, got event 5(rec

v_lacpdu)

009199: 00:28:39: @@@ lacp_rx Gi0/21 - rx: CURRENT -> CURRENT

009200: 00:28:39: LACP: Gi0/21 lacp_action_rx_current entered

009201: 00:28:39: LACP: recordPDU Gi0/21 LACP PDU Rcvd. Partners oper state is h

ex 3D

009202: 00:28:39: LACP: recordPDU Gi0/21 Partner in sync and aggregating

009203: 00:28:39: LACP: Gi0/21 Partners oper state is hex 3D

009204: 00:28:39: LACP: timer lacp_c_l(Gi0/21) started with interval 90000.

009205: 00:28:39: LACP: Gi0/21 LAG_PARTNER_UP.

009206: 00:28:39: LACP: Gi0/21 LAG unchanged@@ lacp_ptx Gi0/36 - ptx: FAST_PERIO

DIC -> SLOW_PERIODIC

009273: 00:28:43: LACP: Gi0/36 lacp_action_ptx_fast_periodic_exit entered

009274: 00:28:43: LACP: lacp_p(Gi0/36) timer stopped

009275: 00:28:43: LACP: Gi0/36 lacp_action_ptx_slow_periodic entered

009276: 00:28:43: LACP: timer lacp_p_s(Gi0/36) started with interval 30000.

009277: 00:28:43:     lacp_rx Gi0/36 - rx: during state PORT_DISABLED, got event

 3(lacp_enabled)

009278: 00:28:43: @@@ lacp_rx Gi0/36 - rx: PORT_DISABLED -> EXPIRED

009279: 00:28:43: LACP: Gi0/36 lacp_action_rx_expired entered

009280: 00:28:43: LACP: Gi0/36 partner timeout mode changed to 1

009281: 00:28:43:     lacp_ptx Gi0/36 - ptx: during state SLOW_PERIODIC, got eve

nt 4(short_timeout)

009282: 00:28:43: @@@ lacp_ptx Gi0/36 - ptx: SLOW_PERIODIC -> PERIODIC_TX

009283: 00:28:43: LACP: Gi0/36 lacp_action_ptx_slow_periodic_exit entered

009284: 00:28:43: LACP: lacp_p(Gi0/36) timer stopped

009285: 00:28:43: LACP: Gi0/36 lacp_action_ptx_periodic_tx entered

009286: 00:28:43: LACP: timer lacp_t(Gi0/36) started with interval 1000.

009287: 00:28:43: LACP: lacp_send_lacpdu: (Gi0/36) About to send the 110 LACPDU

009288: 00:28:43: LACP :lacp_bugpak: Send LACP-PDU packet via Gi0/36

009289: 00:28:43: LACP : packet size: 124

009290: 00:28:43: LACP: pdu: subtype: 1, version: 1

009291: 00:28:43: LACP: Act: tlv:1, tlv-len:20, key:0x26, p-pri:0x8000, p:0x24,

p-state:0x85,

s-pri:0x8000, s-mac:a40c.c399.d780

009292: 00:28:43: LACP: Part: tlv:2, tlv-len:20, key:0x11, p-pri:0x8000, p:0x11,

 p-state:0x6,

s-pri:0x8000, s-mac:0017.efb3.a200

009293: 00:28:43: LACP: col-tlv:3, col-tlv-len:16, col-max-d:0x8000

009294: 00:28:43: LACP: term-tlv:0 termr-tlv-len:0

009295: 00:28:43: LACP: lacp_write: LACP 124 bytes out Gi0/36

009296: 00:28:43:     lacp_ptx Gi0/36 - ptx: during state PERIODIC_TX, got event

 4(short_timeout)

009297: 00:28:43: @@@ lacp_ptx Gi0/36 - ptx: PERIODIC_TX -> FAST_PERIODIC

009298: 00:28:43: LACP: Gi0/36 lacp_action_ptx_fast_periodic entered

009299: 00:28:43: LACP: timer lacp_p_f(Gi0/36) started with interval 1000.

009300: 00:28:43: LACP: timer lacp_c_s(Gi0/36) started with interval 3000.

009301: 00:28:43:     lacp_mux Gi0/36 - mux: during state DETACHED, got event 6(

outof_sync) (ignored)

009302: 00:28:43: LACP :lacp_bugpak: Receive LACP-PDU packet via Gi0/36

009303: 00:28:43: LACP : packet size: 124

009304: 00:28:43: LACP: pdu: subtype: 1, version: 1

009305: 00:28:43: LACP: Act: tlv:1, tlv-len:20, key:0x11, p-pri:0x8000, p:0x11,

p-state:0xD,

s-pri:0x8000, s-mac:0017.efb3.a200

009306: 00:28:43: LACP: Part: tlv:2, tlv-len:20, key:0x26, p-pri:0x8000, p:0x24,

 p-state:0x5,

s-pri:0x8000, s-mac:a40c.c399.d780

009307: 00:28:43: LACP: col-tlv:3, col-tlv-len:16, col-max-d:0x8000

009308: 00:28:43: LACP: term-tlv:0 termr-tlv-len:0

009309: 00:28:43: LACP: Gi0/36 LACP packet received, processing

009310: 00:28:43:     lacp_rx Gi0/36 - rx: during state EXPIRED, got event 5(rec

v_lacpdu)

009311: 00:28:43: @@@ lacp_rx Gi0/36 - rx: EXPIRED -> CURRENT

009312: 00:28:43: LACP: Gi0/36 lacp_action_rx_expired_exit entered

009313: 00:28:43: LACP: lacp_c(Gi0/36) timer stopped

009314: 00:28:43: LACP: Gi0/36 lacp_action_rx_current entered

009315: 00:28:43: LACP: recordPDU Gi0/36 LACP PDU Rcvd. Partners oper state is h

ex 6

009316: 00:28:43: LACP: Gi0/36 partner timeout mode changed to 0

009317: 00:28:43:     lacp_ptx Gi0/36 - ptx: during state FAST_PERIODIC, got eve

nt 2(long_timeout)

009318: 00:28:43: @@@ lacp_ptx Gi0/36 - ptx: FAST_PERIODIC -> SLOW_PERIODIC

009319: 00:28:43: LACP: Gi0/36 lacp_action_ptx_fast_periodic_exit entered

009320: 00:28:43: LACP: lacp_p(Gi0/36) timer stopped

009321: 00:28:43: LACP: Gi0/36 lacp_action_ptx_slow_periodic entered

009322: 00:28:43: LACP: timer lacp_p_s(Gi0/36) started with interval 30000.

009323: 00:28:43: LACP: recordPDU Gi0/36 Partner in sync and aggregating

009324: 00:28:43: LACP: Gi0/36 Partners oper state is hex D

009325: 00:28:43: LACP: timer lacp_c_l(Gi0/36) started with interval 90000.

009326: 00:28:43: LACP: Gi0/36 LAG_PARTNER_UP.

009327: 00:28:43: LACP: Gi0/36 LAG unchanged

009328: 00:28:43: LACP: Gi0/36 cannot create an aggregator

009329: 00:28:43: LACP :lacp_bugpak: Receive LACP-PDU packet via Gi0/36

009330: 00:28:43: LACP : packet size: 124

009331: 00:28:43: LACP: pdu: subtype: 1, version: 1

009332: 00:28:43: LACP: Act: tlv:1, tlv-len:20, key:0x11, p-pri:0x8000, p:0x11,

p-state:0xD,

s-pri:0x8000, s-mac:0017.efb3.a200

009333: 00:28:43: LACP: Part: tlv:2, tlv-len:20, key:0x26, p-pri:0x8000, p:0x24,

 p-state:0x85,

s-pri:0x8000, s-mac:a40c.c399.d780

009334: 00:28:43: LACP: col-tlv:3, col-tlv-len:16, col-max-d:0x8000

009335: 00:28:43: LACP: term-tlv:0 termr-tlv-len:0

009336: 00:28:43: LACP: Gi0/36 LACP packet received, processing

009337: 00:28:43:     lacp_rx Gi0/36 - rx: during state CURRENT, got event 5(rec

v_lacpdu)

009338: 00:28:43: @@@ lacp_rx Gi0/36 - rx: CURRENT -> CURRENT

009339: 00:28:43: LACP: Gi0/36 lacp_action_rx_current entered

009340: 00:28:43: LACP: recordPDU Gi0/36 LACP PDU Rcvd. Partners oper state is h

ex D

009341: 00:28:43: LACP: recordPDU Gi0/36 Partner in sync and aggregating

009342: 00:28:43: LACP: Gi0/36 Partners oper state is hex D

009343: 00:28:43: LACP: timer lacp_c_l(Gi0/36) started with interval 90000.

009344: 00:28:43: LACP: Gi0/36 LAG_PARTNER_UP.

009345: 00:28:43: LACP: Gi0/36 LAG unchanged

009346: 00:28:43: LACP: Gi0/36 cannot create an aggregator

009347: *Mar  1 00:28:45: %SYS-3-CPUHOG: Task is running for (2097)msecs, more t

han (2000)msecs (4/3),process = Logger.

-Traceback= 62C72C 62D874 BB0504 BAF56C BAFCAC BB1D04 975510 96CAE4

009350: *Mar  1 00:28:47: %SYS-3-LOGGER_DROPPED: System dropped 4 console debug

messages.



010663: *Mar  1 00:29:51: %SYS-3-LOGGER_DROPPED: System dropped 2022 console deb

ug messages.



010663: 00:29:51: LACP: lacp_p(Gi0/35) timer stopped

010664: 00:29:51: LACP: lacp_p(Gi0/35) expired

010665: 00:29:51:     lacp_ptx Gi0/35 - ptx: during state SLOW_PERIODIC, got eve

nt 3(pt_expired)

010666: 00:29:51: @@@ lacp_ptx Gi0/35 - ptx: SLOW_PERIODIC -> PERIODIC_TX

010667: 00:29:51: LACP: Gi0/35 lacp_action_ptx_slow_periodic_exit entered

010668: 00:29:51: LACP: lacp_p(Gi0/35) timer stopped

010669: 00:29:51: LACP: Gi0/35 lacp_action_ptx_periodic_tx entered

010670: 00:29:51: LACP: timer lacp_t(Gi0/35) started with interval 1000.

010671: 00:29:51: LACP: lacp_send_lacpdu: (Gi0/35) About to send the 110 LACPDU

010672: 00:29:51: LACP :lacp_bugpak: Send LACP-PDU packet via Gi0/35

010673: 00:29:51: LACP : packet size: 124

010674: 00:29:51: LACP: pdu: subtype: 1, version: 1

010675: 00:29:51: LACP: Act: tlv:1, tlv-len:20, key:0x26, p-pri:0x8000, p:0x23,

p-state:0x3D,

s-pri:0x8000, s-mac:a40c.c399.d780

010676: 00:29:51: LACP: Part: tlv:2, tlv-len:20, key:0x12, p-pri:0x8000, p:0x12,

 p-state:0x3D,

s-pri:0x8000, s-mac:0017.efb3.a200

010677: 00:29:51: LACP: col-tlv:3, col-tlv-len:16, col-max-d:0x8000

010678: 00:29:51: LACP: term-tlv:0 termr-tlv-len:0

010679: 00:29:51: LACP: lacp_write: LACP 124 bytes out Gi0/35

010680: 00:29:51:     lacp_ptx Gi0/35 - ptx: during state PERIODIC_TX, got event

 2(long_timeout)

010681: 00:29:51: @@@ lacp_ptx Gi0/35 - ptx: PERIODIC_TX -> SLOW_PERIODIC

010682: 00:29:51: LACP: Gi0/35 lacp_action_ptx_slow_periodic entered

010683: 00:29:51: LACP: timer lacp_p_s(Gi0/35) started with interval 30000.

010684: 00:29:52: LACP: lacp_t(Gi0/35) timer stopped

010685: 00:29:52: LACP: lacp_t(Gi0/35) expired

010686: 00:29:52: LACP :lacp_bugpak: Receive LACP-PDU packet via Gi0/19

010687: 00:29:52: LACP : packet size: 124

010688: 00:29:52: LACP: pdu: subtype: 1, version: 1

010689: 00:29:52: LACP: Act: tlv:1, tlv-len:20, key:0x3, p-pri:0x8000, p:0x14, p

-state:0x3D,

s-pri:0x8000, s-mac:0024.f9ea.8000

010690: 00:29:52: LACP: Part: tlv:2, tlv-len:20, key:0x1, p-pri:0x8000, p:0x13,

p-state:0x3D,

s-pri:0x8000, s-mac:a40c.c399.d780

010691: 00:29:52: LACP: col-tlv:3, col-tlv-len:16, col-max-d:0x8000

010692: 00:29:52: LACP: term-tlv:0 termr-tlv-len:0

010693: 00:29:52: LACP: Gi0/19 LACP packet received, processing

010694: 00:29:52:     lacp_rx Gi0/19 - rx: during state CURRENT, got event 5(rec

v_lacpdu)

010695: 00:29:52: @@@ lacp_rx Gi0/19 - rx: CURRENT -> CURRENT

010696: 00:29:52: LACP: Gi0/19 lacp_action_rx_current entered

010697: 00:29:52: LACP: recordPDU Gi0/19 LACP PDU Rcvd. Partners oper state is h

ex 3D

010698: 00:29:52: LACP: recordPDU Gi0/19 Partner in sync and aggregating

010699: 00:29:52: LACP: Gi0/19 Partners oper state is hex 3D

010700: 00:29:52: LACP: timer lacp_c_l(Gi0/19) started with interval 90000.

010701: 00:29:52: LACP: Gi0/19 LAG_PARTNER_UP.

010702: 00:29:52: LACP: Gi0/19 LAG unchanged

010703: 00:29:52:     lacp_mux Gi0/19 - mux: during state COLLECTING_DISTRIBUTIN

G, got event 5(in_sync) (ignored)

010704: 00:29:53: LACP: lacp_hw_off: Gi0/36 is going down



010705: 00:29:53: LACP: if_down: Gi0/36

010706: 00:29:53:     lacp_ptx Gi0/36 - ptx: during state SLOW_PERIODIC, got eve

nt 0(no_periodic)

010707: 00:29:53: @@@ lacp_ptx Gi0/36 - ptx: SLOW_PERIODIC -> NO_PERIODIC

010708: 00:29:53: LACP: Gi0/36 lacp_action_ptx_slow_periodic_exit entered

010709: 00:29:53: LACP: lacp_p(Gi0/36) timer stopped

010710: 00:29:53: LACP: Gi0/36 lacp_action_ptx_no_periodic entered

010711: 00:29:53: LACP: lacp_p(Gi0/36) timer stopped

010712: 00:29:53:     lacp_rx Gi0/36 - rx: during state CURRENT, got event 1(por

t_disabled)

010713: 00:29:53: @@@ lacp_rx Gi0/36 - rx: CURRENT -> PORT_DISABLED

010714: 00:29:53: LACP: Gi0/36 lacp_action_rx_current_exit entered

010715: 00:29:53: LACP: lacp_c(Gi0/36) timer stopped

010716: 00:29:53: LACP: Gi0/36 lacp_action_rx_port_disabled entered

010717: 00:29:53:     lacp_mux Gi0/36 - mux: during state DETACHED, got event 6(

outof_sync) (ignored)

010718: 00:29:53: LACP: lacp_c(Gi0/36) timer stopped

010719: 00:29:53: LACP: lacp_p(Gi0/36) timer stopped

010720: 00:29:53: LACP: lacp_w(Gi0/36) timer stopped

010721: 00:29:53: LACP: lacp_t(Gi0/36) timer stopped

010722: 00:29:53: LACP: lacp_hw_off: send pdu out Gi0/36

010723: 00:29:53: LACP: lacp_send_lacpdu: (Gi0/36) About to send the 110 LACPDU

010724: 00:29:53: LACP :lacp_bugpak: Send LACP-PDU packet via Gi0/36

010725: 00:29:53: LACP : packet size: 124

010726: 00:29:53: LACP: pdu: subtype: 1, version: 1

010727: 00:29:53: LACP: Act: tlv:1, tlv-len:20, key:0x26, p-pri:0x8000, p:0x24,

p-state:0x5,

s-pri:0x8000, s-mac:a40c.c399.d780

010728: 00:29:53: LACP: Part: tlv:2, tlv-len:20, key:0x11, p-pri:0x8000, p:0x11,

 p-state:0x4,

s-pri:0x8000, s-mac:0017.efb3.a200

010729: 00:29:53: LACP: col-tlv:3, col-tlv-len:16, col-max-d:0x8000

010730: 00:29:53: LACP: term-tlv:0 termr-tlv-len:0

010731: 00:29:53: LACP: lacp_write: LACP 124 bytes out Gi0/36

010732: 00:29:53: LACP: Gi0/36 oper-key: 0x26

010733: 00:29:53: LACP: lacp_hw_on: Gi0/36 is coming up



010734: 00:29:53:     lacp_ptx Gi0/36 - ptx: during state NO_PERIODIC, got event

 0(no_periodic)

010735: 00:29:53: @@@ lacp_ptx Gi0/36 - ptx: NO_PERIODIC -> NO_PERIODIC

010736: 00:29:53: LACP: Gi0/36 lacp_action_ptx_no_periodic entered

010737: 00:29:53: LACP: lacp_p(Gi0/36) timer stopped

010738: 00:29:53:     lacp_ptx Gi0/36 - ptx: during state NO_PERIODIC, got event

 1(start_periodic)

010739: 00:29:53: @@@ lacp_ptx Gi0/36 - ptx: NO_PERIODIC -> FAST_PERIODIC

010740: 00:29:53: LACP: Gi0/36 lacp_action_ptx_fast_periodic entered

010741: 00:29:53: LACP: timer lacp_p_f(Gi0/36) started with interval 1000.

010742: 00:29:53:     lacp_ptx Gi0/36 - ptx: during state FAST_PERIODIC, got eve

nt 2(long_timeout)

010743: 00:29:53: @@@ lacp_ptx Gi0/36 - ptx: FAST_PERIODIC -> SLOW_PERIODIC

010744: 00:29:53: LACP: Gi0/36 lacp_action_ptx_fast_periodic_exit entered

010745: 00:29:53: LACP: lacp_p(Gi0/36) timer stopped

010746: 00:29:53: LACP: Gi0/36 lacp_action_ptx_slow_periodic entered

010747: 00:29:53: LACP: timer lacp_p_s(Gi0/36) started with interval 30000.

010748: 00:29:53:     lacp_rx Gi0/36 - rx: during state PORT_DISABLED, got event

 3(lacp_enabled)

010749: 00:29:53: @@@ lacp_rx Gi0/36 - rx: PORT_DISABLED -> EXPIRED

010750: 00:29:53: LACP: Gi0/36 lacp_action_rx_expired entered

010751: 00:29:53: LACP: Gi0/36 partner timeout mode changed to 1

010752: 00:29:53:     lacp_ptx Gi0/36 - ptx: during state SLOW_PERIODIC, got eve

nt 4(short_timeout)

010753: 00:29:53: @@@ lacp_ptx Gi0/36 - ptx: SLOW_PERIODIC -> PERIODIC_TX

010754: 00:29:53: LACP: Gi0/36 lacp_action_ptx_slow_periodic_exit entered

010755: 00:29:53: LACP: lacp_p(Gi0/36) timer stopped

010756: 00:29:53: LACP: Gi0/36 lacp_action_ptx_periodic_tx entered

010757: 00:29:53: LACP: timer lacp_t(Gi0/36) started with interval 1000.

010758: 00:29:53: LACP: lacp_send_lacpdu: (Gi0/36) About to send the 110 LACPDU

010759: 00:29:53: LACP :lacp_bugpak: Send LACP-PDU packet via Gi0/36

010760: 00:29:53: LACP : packet size: 124

010761: 00:29:53: LACP: pdu: subtype: 1, version: 1

010762: 00:29:53: LACP: Act: tlv:1, tlv-len:20, key:0x26, p-pri:0x8000, p:0x24,

p-state:0x85,

s-pri:0x8000, s-mac:a40c.c399.d780

010763: 00:29:53: LACP: Part: tlv:2, tlv-len:20, key:0x11, p-pri:0x8000, p:0x11,

 p-state:0x6,

s-pri:0x8000, s-mac:0017.efb3.a200

010764: 00:29:53: LACP: col-tlv:3, col-tlv-len:16, col-max-d:0x8000

010765: 00:29:53: LACP: term-tlv:0 termr-tlv-len:0

010766: 00:29:53: LACP: lacp_write: LACP 124 bytes out Gi0/36

010767: 00:29:53:     lacp_ptx Gi0/36 - ptx: during state PERIODIC_TX, got event

 4(short_timeout)

010768: 00:29:53: @@@ lacp_ptx Gi0/36 - ptx: PERIODIC_TX -> FAST_PERIODIC

010769: 00:29:53: LACP: Gi0/36 lacp_action_ptx_fast_periodic entered

010770: 00:29:53: LACP: timer lacp_p_f(Gi0/36) started with interval 1000.

010771: 00:29:53: LACP: timer lacp_c_s(Gi0/36) started with interval 3000.

010772: 00:29:53:     lacp_mux Gi0/36 - mux: during state DETACHED, got event 6(

outof_sync) (ignored)

010773: 00:29:53: LACP :lacp_bugpak: Receive LACP-PDU packet via Gi0/36

010774: 00:29:53: LACP : packet size: 124

010775: 00:29:53: LACP: pdu: subtype: 1, version: 1

010776: 00:29:53: LACP: Act: tlv:1, tlv-len:20, key:0x11, p-pri:0x8000, p:0x11,

p-state:0xD,

s-pri:0x8000, s-mac:0017.efb3.a200

010777: 00:29:53: LACP: Part: tlv:2, tlv-len:20, key:0x26, p-pri:0x8000, p:0x24,

 p-state:0x5,

s-pri:0x8000, s-mac:a40c.c399.d780

010778: 00:29:53: LACP: col-tlv:3, col-tlv-len:16, col-max-d:0x8000

010779: 00:29:53: LACP: term-tlv:0 termr-tlv-len:0

010780: 00:29:53: LACP: Gi0/36 LACP packet received, processing

010781: 00:29:53:     lacp_rx Gi0/36 - rx: during state EXPIRED, got event 5(rec

v_lacpdu)

010782: 00:29:53: @@@ lacp_rx Gi0/36 - rx: EXPIRED -> CURRENT

010783: 00:29:53: LACP: Gi0/36 lacp_action_rx_expired_exit entered

010784: 00:29:53: LACP: lacp_c(Gi0/36) timer stopped

010785: 00:29:53: LACP: Gi0/36 lacp_action_rx_current entered

010786: 00:29:53: LACP: recordPDU Gi0/36 LACP PDU Rcvd. Partners oper state is h

ex 6

010787: 00:29:53: LACP: Gi0/36 partner timeout mode changed to 0

010788: 00:29:53:     lacp_ptx Gi0/36 - ptx: during state FAST_PERIODIC, got eve

nt 2(long_timeout)

010789: 00:29:53: @@@ lacp_ptx Gi0/36 - ptx: FAST_PERIODIC -> SLOW_PERIODIC

010790: 00:29:53: LACP: Gi0/36 lacp_action_ptx_fast_periodic_exit entered

010791: 00:29:53: LACP: lacp_p(Gi0/36) timer stopped

010792: 00:29:53: LACP: Gi0/36 lacp_action_ptx_slow_periodic entered

010793: 00:29:53: LACP: timer lacp_p_s(Gi0/36) started with interval 30000.

010794: 00:29:53: LACP: recordPDU Gi0/36 Partner in sync and aggregating

010795: 00:29:53: LACP: Gi0/36 Partners oper state is hex D

010796: 00:29:53: LACP: timer lacp_c_l(Gi0/36) started with interval 90000.

010797: 00:29:53: LACP: Gi0/36 LAG_PARTNER_UP.

010798: 00:29:53: LACP: Gi0/36 LAG unchanged

010799: 00:29:53: LACP: Gi0/36 cannot create an aggregator

010800: 00:29:53: LACP :lacp_bugpak: Receive LACP-PDU packet via Gi0/36

010801: 00:29:53: LACP : packet size: 124

010802: 00:29:53: LACP: pdu: subtype: 1, version: 1

010803: 00:29:53: LACP: Act: tlv:1, tlv-len:20, key:0x11, p-pri:0x8000, p:0x11,

p-state:0xD,

s-pri:0x8000, s-mac:0017.efb3.a200

010804: 00:29:53: LACP: Part: tlv:2, tlv-len:20, key:0x26, p-pri:0x8000, p:0x24,

 p-state:0x85,

s-pri:0x8000, s-mac:a40c.c399.d780

010805: 00:29:53: LACP: col-tlv:3, col-tlv-len:16, col-max-d:0x8000

010806: 00:29:53: LACP: term-tlv:0 termr-tlv-len:0

010807: 00:29:53: LACP: Gi0/36 LACP packet received, processing

010808: 00:29:53:     lacp_rx Gi0/36 - rx: during state CURRENT, got event 5(rec

v_lacpdu)

010809: 00:29:53: @@@ lacp_rx Gi0/36 - rx: CURRENT -> CURRENT

010810: 00:29:53: LACP: Gi0/36 lacp_action_rx_current entered

010811: 00:29:53: LACP: recordPDU Gi0/36 LACP PDU Rcvd. Partners oper state is h

ex D

010812: 00:29:535:3: LACP: G i0/36 LAG_LPARTNER_UPA.

010816:C 00:29:53:P LACP: G:i 0/36 LAG urnchanged

U010817: 00c:29:53: LAoCP: Gi0/36r cannot crdeate an PaDggregator

 010818: 0 0:29:54: LGACP: lacp_it(Gi0/36) 0timer stop/ped

0108139: 00:29:564: LACP: l acp_t(Gi0/P36) expireadrtn

010e82r0: 00:2 9:54: LACPi: lacpn_p( Gi0/51) tismer stoppeyd

010821:n 00:29c:54 : LACP: laacp_p(Gi0/5n1) expiredd

010822:  00:29:54: a    lacp_pgtx Gi0/51 g- ptx: durring state eSLOW_PERIOgDIC,

got eavent 3(pt_texpired)

 Gi0/51 - 0n:29:54: @@g@ lacp_ptx

          ptx: S0LOW1_PERIODIC 0-> PERIODI8C_TX

0108124: 00:29:354: LACP: :Gi0/51 lac p_action_p0tx_slow_pe0riodic_exi:t entered

2

 010825: 090:29:54: L:ACP: lacp_5p(Gi0/51) 3timer stop:ped

0 108L26: 00:29:A54: LACP: CGi0/51 lacPp_acti:on_ ptx_periodGic_tx enteired

0108207: 00:29:5/4: LACP: t3imer lacp_6t(Gi0/51)  started wiPth intervaal 1000.

0r10828: 00:t29:54:n LAeCP: lacp_srend_lascpd u: (Gi0/51o) Aboupt teo send ther

110 LACPD Ust

01082a9: 00:t29:e54: LACP : lacp_biugpsak: Send L ACP-PDhU peacket via xGi0/51

29:54:0: 00:

       LA0CP : packe1t size0: 1824

0108311: 00:249:5:4: LACP: p du: su0bty0pe: 1, ver:sion: 21

9010832: 00::29:545: L3ACP: Act: :tlv:1,  tlLv-len:20, AkeCy:P0x2:, p-pri:0x 800

r, tp:0ix33, p-stamte:0x3eD,

 s-pri:0x8 000, sl-maac:a40c.c39c9.d780p

0_10833: 00:c29:54:_ LAlCP: Part: (tlv:2,G tliv-len:20, 0key:0x/4, 3p-pri:0x8060

0, p:)0x3 3, p-states:0x3D,t

sa-pri:0x800r0, s-mtac:e0019.0694.d6000

 010w834: 00:29i:54: LtACPh: col-tlv: 3, coli-tlnv-len:16, tcol-maex-dr:0x8000

v010835a: 0l0:29:54: L ACP: t9erm0-tlv:0 ter0mr-tlv0-le0n:0

29:83.6: 00:

   54: LACP: 0lacp_w1rit0e: LACP 1284 byte1s o5ut Gi0/51 : 00:29:

010837: 00:29:54:     lacp_ptx Gi0/51 - ptx: during state PERIODIC_TX, got event

 2(long_timeout)

010838: 00:29:54: @@@ lacp_ptx Gi0/51 - ptx: PERIODIC_TX -> SLOW_PERIODIC

010839: 00:29:54: LACP: Gi0/51 lacp_action_ptx_slow_periodic entered

010840: 00:29:54: LACP: timer lacp_p_s(Gi0/51) started with interval 30000.

010841: 00:29:55: LACP: lacp_t(Gi0/51) timer stopped

010842: 00:29:55: LACP: lacp_t(Gi0/51) expired

010843: 00:29:55: LACP: lacp_p(Gi0/19) timer stopped

010844: 00:29:55: LACP: lacp_p(Gi0/19) expired

010845: 00:29:55:     lacp_ptx Gi0/19 - ptx: during state SLOW_PERIODIC, got eve

nt 3(pt_expired)

010846: 00:29:55: @@@ lacp_ptx Gi0/19 - ptx: SLOW_PERIODIC -> PERIODIC_TX

010847: 00:29:55: LACP: Gi0/19 lacp_action_ptx_slow_periodic_exit entered

010848: 00:29:55: LACP: lacp_p(Gi0/19) timer stopped

010849: 00:29:55: LACP: Gi0/19 lacp_action_ptx_periodic_tx entered

010850: 00:29:55: LACP: timer lacp_t(Gi0/19) started with interval 1000.

010851: 00:29:55: LACP: lacp_send_lacpdu: (Gi0/19) About to send the 110 LACPDU

010852: 00:29:55: LACP :lacp_bugpak: Send LACP-PDU packet via Gi0/19

010853: 00:29:55: LACP : packet size: 124

010854: 00:29:55: LACP: pdu: subtype: 1, version: 1

010855: 00:29:55: LACP: Act: tlv:1, tlv-len:20, key:0x1, p-pri:0x8000, p:0x13, p

-state:0x3D,

s-pri:0x8000, s-mac:a40c.c399.d780

010856: 00:29:55: LACP: Part: tlv:2, tlv-len:20, key:0x3, p-pri:0x8000, p:0x14,

p-state:0x3D,

s-pri:0x8000, s-mac:0024.f9ea.8000

010857: 00:29:55: LACP: col-tlv:3, col-tlv-len:16, col-max-d:0x8000

010858: 00:29:55: LACP: term-tlv:0 termr-tlv-len:0

010859: 00:29:55: LACP: lacp_write: LACP 124 bytes out Gi0/19

010860: 00:29:55:     lacp_ptx Gi0/19 - ptx: during s58: tLACP : pacaket size: t

e24

 0108 68: 00:29:P58: LACP: Epdu: subtyRpe: I1, veOrsion: 1

D010869: 00I:29:58: LACCP: Act: t_lv:1, tlv-Tlen:20, keXy:0x4, p-p,ri:0x8000,  p

:0x33, pg-state:0x3oD,

s-prti: 0x8000, s-emac:0019.0v694.6000

e010870: 00n:29:58: LAtCP: Part:  tlv:2, tlv2-len:20, k(eyl:0x2, po-pri:0x800n0,

g p:0x33_, p-state:t0xi3D,

s-mpri:0x8000e, s-mac:a4o0c.c399.d7u80

LACP: c: 00:29:58):

       ol-tlv:3, 0co1l-tlv-l0en:16, col8-m6ax-d:0x18000

010:87 2: 00:209:58: LACP0: :term-tl2v:0 termr-9tl:v-len:05

p10873: 500::29:58:  LACP: Gi0@/5@1 LACP @packet rec eilved, praocessing cp_

 010874t: 00:29:58x:     lacp _rx Gi0/51G - rx: duriing state 0CU/RRENT, 1got ev

ent 95( recv_la-cpdu)

O10 87p5: 00:2t9:58: @@@ xla:cp_rx G i0/51 - rxP: ECURRENTR -> CURRENIT

 010876D: 00:29:58I: LACP: GiC0/51 lacp__action_rx_Tcurrent enXte red

01-0877: 00:2>9: 58: LACSP: recordPLDU Gi0/51 OLACP PDU RWcv_d. PartPners oper E

stRate is Ihex 3D

 record8: 00:I29:58: LACCP:

       PDU Gi0/510 Partner i1n sync and0 a8ggregat6ing

0108729:: 00:29: 58: LACP: 0Gi0/51 Par0tners oper: s2tate is9 hex 3D

0:105880: 005:29:58: LA:CP : timerL lacp_c_l(AGiC0/51) sPtarted wit:h interval

90000.

0G10i881: 000:29:58: LA/CP1: Gi0/591 LAG_PART NER_UP.

0l10882: 00:a29:58: LACcP: Gi0/51 pLA_G unchaangedction_pt

x01088_3: 00:29:5s8:  l   laocp_mux Gi0w/51 _- muxp: during setater COLLiECTING_

DISoTRIBdUTINGi, got evenct 5( in_syenc) (ignorned)

 timet4: 00:29:5e9: LrACP: elacp_p(Gi0d/49)

0    r stopped

 0101885: 000:29:59: 8LACP6: lac3p_p(Gi0/49:) ex pired0

010886: 000:2:9:59:2     lacp_9ptx Gi0/49: - ptx: du5ring state5 SLOW_PERI:ODIC

, gotL event 3(pAt_exCpiredP)

010887:: 00:29:59:  @@@ lacp_tptx iGi0/4m9 - ptx: SeLOW_rPERIO DIC -> PERlIODIaC

cTX

 010888: 0p0:29_:59: pLACP: Gi0/_49 lsacp_a(ction_ptx_Gslowi_per0iodic_exit/ ent

9ered

 010889: 0)0:29 :59: sLACP: lacpt_p(Gi0/49)a timer storppedt

010e890: 00:29d:59:  LACPw: Gi0/49 liacp_actiont_ptx_periohdic_tx ent ered

0108i91: n00:29t:59: LACP:e timrer lavcp_t(Gi0/4a9) startedl with inte rval 1000

.3

010892: 000:209:59:0 LACP: 0.

010l8acp_s6end_lacpdu4: (G:i0/49 ) About to0 sen0d the: 110 LACPD2U

0910893:: 00:29:595: LA6CP :l:acp_bugpak : SeLnd LAACP-PDU pacCket Pvia G:i0/49

010 894:l 00:2a9:59: LACPc : ppacket_ size: 124t

010895: (00:29:59: GLACPi: pdu0: subtype:/ 1, 1versi9on: 1

010)896:  00:2t9:59: LACPi: Acmt: tlev:1, tlv-lren:20, key :0x2, p-prsi:0xt8000,

o p:0x31, pp-stapte:0xe3D,

-mac:a40c.000, s

0         c399.d780

 010897: 010:290:59: 8LACP: Part6: tl5v:2, :tlv-len:20 , key:0x4,0 p-pri:0x80000

,: p:0x231, p-stat9e:0x:3D,

5s-pri:0x680:00 , s-macL:0019.0694A.6C000

01P0898: 00:2:9:59: LACP : col-tlv:l3, col-tlva-len:16, ccolp-max-d:_0x8000

0t10(899: 00G:29:59: LAiCP: term-t0lv:0 termr/-tlv-len:01

010900: 900):29:59:  LACP: lacep_xwrite: pLACP 124 biytes out Gri0/49 ed

010866: 00:29:58: LACP :lacp_bugpa:k 00:29:59:: L ACP: pdRu: subtypee: c1, verse

ion: 1

01i0908: 00:2v9:59: LACPe: Act: tlv :1, tlv-leLn:A20, keyC:0x4, p-prPi:0x8000, -

p:0x31, p-PstDate:0x3UD,

s-pri: 0x8000, s-pmac:0019.0a69c4.6000ket via Gi0/51

010867: 00:29:

010901: 00:29:59:     lacp_ptx Gi0/49 - ptx: during state PERIODIC_TX, got event

 2(long_timeout)

010902: 00:29:59: @@@ lacp_ptx Gi0/49 - ptx: PERIODIC_TX -> SLOW_PERIODIC

010903: 00:29:59: LACP: Gi0/49 lacp_action_ptx_slow_periodic entered

010904: 00:29:25: 00:30:01: LACP :lacp_bugpak: Receive LACP-PDU packet via Gi0/2

1

010926: 00:30:01: LACP : packet size: 124

010927: 00:30:01: LACP: pdu: subtype: 1, version: 1

010928: 00:30:01: LACP: Act: tlv:1, tlv-len:20, key:0x3, p-pri:0x8000, p:0x16, p

-state:0x3D,

s-pri:0x8000, s-mac:0024.f9ea.8000

010929: 00:30:01: LACP: Part: tlv:2, tlv-len:20, key:0x1, p-pri:0x8000, p:0x15,

p-state:0x3D,

s-pri:0x8000, s-mac:a40c.c399.d780

010930: 00:30:01: LACP: col-tlv:3, col-tlv-len:16, col-max-d:0x8000

010931: 00:30:01: LACP: term-tlv:0 termr-tlv-len:0

010932: 00:30:01: LACP: Gi0/21 LACP packet received, processing

010933: 00:30:01:     lacp_rx Gi0/21 - rx: during state CURRENT, got event 5(rec

v_lacpdu)

010934: 00:30:01: @@@ lacp_rx Gi0/21 - rx: CURRENT -> CURRENT

010935: 00:30:01: LACP: Gi0/21 lacp_action_rx_current entered

010936: 00:30:01: LACP: recordPDU Gi0/21 LACP PDU Rcvd. Partners oper state is h

ex 3D

010937: 00:30:01: LACP: recordPDU Gi0/21 Partner in sync and aggregating

010938: 00:30:01: LACP: Gi0/21 Partners oper state is hex 3

Open in new window

0
 

Author Comment

by:LSolt
ID: 33437131
Bottom-Switch#sh etherchannel port-channel
                Channel-group listing:
                ----------------------

Group: 1
----------
                Port-channels in the group:
                ---------------------------

Port-channel: Po1    (Primary Aggregator)

------------

Age of the Port-channel   = 0d:00h:30m:07s
Logical slot/port   = 2/1          Number of ports = 3
HotStandBy port = null
Port state          = Port-channel Ag-Inuse
Protocol            =   LACP

Ports in the Port-channel:

Index   Load   Port     EC state        No of bits
------+------+------+------------------+-----------
  0     00     Gi0/17   Active             0
  0     00     Gi0/19   Active             0
  0     00     Gi0/21   Active             0

Time since last port bundled:    0d:00h:29m:56s    Gi0/21

Group: 2
----------
                Port-channels in the group:
                ---------------------------

Port-channel: Po2    (Primary Aggregator)

------------

Age of the Port-channel   = 0d:00h:30m:07s
Logical slot/port   = 2/2          Number of ports = 2
HotStandBy port = null
Port state          = Port-channel Ag-Inuse
Protocol            =   LACP

Ports in the Port-channel:

Index   Load   Port     EC state        No of bits
------+------+------+------------------+-----------
  0     00     Gi0/49   Active             0
  0     00     Gi0/51   Active             0

Time since last port bundled:    0d:00h:30m:00s    Gi0/51

Group: 38
----------
                Port-channels in the group:
                ---------------------------

Port-channel: Po38    (Primary Aggregator)

------------

Age of the Port-channel   = 0d:00h:30m:07s
Logical slot/port   = 2/38          Number of ports = 1
HotStandBy port = null
Port state          = Port-channel Ag-Inuse
Protocol            =   LACP

Ports in the Port-channel:

Index   Load   Port     EC state        No of bits
------+------+------+------------------+-----------
  0     00     Gi0/35   Active             0

Time since last port bundled:    0d:00h:29m:57s    Gi0/35

Bottom-Switch#
0
 

Author Comment

by:LSolt
ID: 33437158
This is interesting... The CLI is totally different than what the GUI is showing...

>> LACP# dump
port  lacp      adminkey  operkey  selected    prio    attached  trunk
                                                         aggr
----------------------------------------------------------------------
INT1   off             1        1         n    32768        --     --
INT2   off             2        2         n    32768        --     --
INT3   off             3        3         n    32768        --     --
INT4   off             4        4         n    32768        --     --
INT5   off             5        5         n    32768        --     --
INT6   off             6        6         n    32768        --     --
INT7   off             7        7         n    32768        --     --
INT8   off             8        8         n    32768        --     --
INT9   off             9        9         n    32768        --     --
INT10  off            10       10         n    32768        --     --
INT11  off            11       11         n    32768        --     --
INT12  off            12       12         n    32768        --     --
INT13  off            13       13         n    32768        --     --
INT14  off            14       14         n    32768        --     --
EXT1   active         17       17         y    32768        17     15
EXT2   active         18       18         y    32768        18     14
EXT3   off            19       19         n    32768        --     --
EXT4   off            20       20         n    32768        --     --
EXT5   off            21       21         n    32768        --     --
EXT6   off            22       22         n    32768        --     --
>> LACP#
0
 
LVL 4

Expert Comment

by:cdowdy
ID: 33437162
I have a number of LACP links in my network, although they are all Cisco->Cisco, or Cisco->Junos and they are all trunks.

You might try trunking the cisco side to see if they will aggregate, but leaving the vlan 1 untagged like this:

conf t
interface range G0/35 - 37
switchport
switchport mode trunk
switchport trunk allowed vlan 1
switchport trunk native vlan 1
channel-group 38 mode active
shut
no shut
int po38
switchport
switchport mode trunk
switchport trunk allowed vlan 1
switchport trunk native vlan 1
shut
no shut
end

then do >sh etherchannel port-channel
0
 
LVL 4

Accepted Solution

by:
cdowdy earned 500 total points
ID: 33437178
Wait on the trunking.. I think on the nortel, the admin keys must match on all ports. Try making all 3 on the nortel active mode lacp and setting the same admin key on every port you want in the bundle
0
 

Author Comment

by:LSolt
ID: 33437191
That was correct in the GUI but not in the CLI. I went in and config via CLI and it now is working fine!!!
0
 

Author Closing Comment

by:LSolt
ID: 33437194
Two sets of eyes are ALWAYS better than one!!! Good JOB!!!
0
 

Author Comment

by:LSolt
ID: 33437199
Here is the final dump!

>> LACP# dump
port  lacp      adminkey  operkey  selected    prio    attached  trunk
                                                         aggr
----------------------------------------------------------------------
INT1   off             1        1         n    32768        --     --
INT2   off             2        2         n    32768        --     --
INT3   off             3        3         n    32768        --     --
INT4   off             4        4         n    32768        --     --
INT5   off             5        5         n    32768        --     --
INT6   off             6        6         n    32768        --     --
INT7   off             7        7         n    32768        --     --
INT8   off             8        8         n    32768        --     --
INT9   off             9        9         n    32768        --     --
INT10  off            10       10         n    32768        --     --
INT11  off            11       11         n    32768        --     --
INT12  off            12       12         n    32768        --     --
INT13  off            13       13         n    32768        --     --
INT14  off            14       14         n    32768        --     --
EXT1   active         38       38         y    32768        17     14
EXT2   active         38       38         y    32768        17     14
EXT3   active         38       38         y    32768        17     14
EXT4   off            20       20         n    32768        --     --
EXT5   off            21       21         n    32768        --     --
EXT6   off            22       22         n    32768        --     --
>> LACP#
0
 
LVL 4

Expert Comment

by:cdowdy
ID: 33437200
Awesome, I was getting worried there!!
0

Featured Post

What Security Threats Are You Missing?

Enhance your security with threat intelligence from the web. Get trending threat insights on hackers, exploits, and suspicious IP addresses delivered to your inbox with our free Cyber Daily.

Join & Write a Comment

Hello All, I have been training on Multicast for a while now and whenever I start the topic , I find out that my friends /  Colleagues mention that they do not know how to test Multicast Joins. As most of the multicast would be video traffic and …
Before I go to far, let's explain HA (High Availability) and why you should consider it.  High availability is the mechanism used to provide redundancy to any service at the same site and appears as a single service to the users of that service.  As…
Excel styles will make formatting consistent and let you apply and change formatting faster. In this tutorial, you'll learn how to use Excel's built-in styles, how to modify styles, and how to create your own. You'll also learn how to use your custo…
This video explains how to create simple products associated to Magento configurable product and offers fast way of their generation with Store Manager for Magento tool.

705 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

20 Experts available now in Live!

Get 1:1 Help Now