Still celebrating National IT Professionals Day with 3 months of free Premium Membership. Use Code ITDAY17

x
?
Solved

Netgear GSM7224V2 - ProSafe 24G Basic Connectivity Query

Posted on 2010-08-16
2
Medium Priority
?
1,339 Views
Last Modified: 2012-05-10
Could someone please help with a query setting up basic connectivity on a Netgear GSM7224V2 - ProSafe 24G Switch.

I am trying to ping from the switch to pc on the same subnet.

Steps taken so far:

1. Factory reset Switch, switch picks up IP details via DHCP
2. Logging into the switch CLI and issuing PING command

Both switch and pc are on the same subnet.  I can ping from the PC to the switch, but not from the switch to the PC...  Could anyone assist please?

Some output from the switch below.

Thanks in advance.
(GSM7224V2) >show network

Interface Status............................... Always Up
IP Address..................................... 10.20.0.141
Subnet Mask.................................... 255.255.255.0
Default Gateway................................ 10.20.0.254
IPv6 Administrative Mode....................... Enabled
IPv6 Prefix is ................................ FE80::3246:9AFF:FE16:968/64
Burned In MAC Address.......................... 30:46:9A:16:09:68
Locally Administered MAC address............... 00:00:00:00:00:00
MAC Address Type............................... Burned In
Configured IPv4 Protocol....................... DHCP
Configured IPv6 Protocol....................... None
IPv6 AutoConfig Mode........................... Disabled
Management VLAN ID............................. 1

(GSM7224V2) >show ip interface b

                                                    Netdir   Multi
Interface    State  IP Address      IP Mask         Bcast    CastFwd
----------   -----  --------------- --------------- -------- --------

(GSM7224V2) >

Open in new window

0
Comment
Question by:Suncore
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
2 Comments
 
LVL 4

Accepted Solution

by:
cdowdy earned 2000 total points
ID: 33450980
Windows I guess? Sounds like windows firewall is on and blocking pings. If you can ping the switch and both are on the same subnet, I'd check that first
0
 
LVL 2

Author Closing Comment

by:Suncore
ID: 33451004
I honestly can not believe I didnt think of that... thankyou so much..
0

Featured Post

Take our survey for a chance to win!

As a valued customer of Targus, we’d like to ask you a few questions about us. As thanks, you will be automatically entered for a chance to win a $500 VISA gift card. To enter, just complete the survey by September 15, 2017.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Before I go to far, let's explain HA (High Availability) and why you should consider it.  High availability is the mechanism used to provide redundancy to any service at the same site and appears as a single service to the users of that service.  As…
How to set-up an On Demand, IPSec, Site to SIte, VPN from a Draytek Vigor Router to a Cyberoam UTM Appliance. A concise guide to the settings required on both devices
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Suggested Courses

704 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question