asked on

Routing issue's

I am trying to get traffic from 10.147.8.2 to be able to see the 90.0.0.2 network
it is connected via t1 Serial0/2/0.

Serial0/2/0 points to the remote office 10.0.3.1
fyi ip route 0.0.0.0 0.0.0.0 10.147.8.15 is a ISA server that is for internet
the config is below.

interface FastEthernet0/0
description ETHERNET INTERFACE
ip address 10.147.8.241 255.255.255.0
ip accounting output-packets
ip accounting precedence input
ip accounting precedence output
no ip mroute-cache
duplex auto
speed auto
bridge-group 1
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/2/0
description FRAME PORT - xxxxx
bandwidth 1544
no ip address
encapsulation frame-relay
load-interval 30
fair-queue
!
interface Serial0/2/0.1 multipoint

ip address 10.0.3.2 255.255.255.252
frame-relay interface-dlci 271
!

!
ip classless
ip route 0.0.0.0 0.0.0.0 10.147.8.15
ip route 10.147.4.7 255.255.255.255 10.147.8.3
ip route 10.147.16.14 255.255.255.255 10.0.3.1
ip route 90.0.0.0 255.255.255.0 10.0.3.1

ip route 90.0.0.0 255.255.255.0 10.147.8.249 50
ip route 90.0.0.253 255.255.255.255 10.0.3.1
ip route 90.0.1.0 255.255.255.0 10.0.0.2
ip route 90.0.2.0 255.255.255.0 10.0.1.2
ip route 90.0.3.0 255.255.255.0 10.0.2.2
ip route 170.209.0.2 255.255.255.255 10.147.8.242
ip route 170.209.0.3 255.255.255.255 10.147.8.242
ip route 199.38.140.0 255.255.255.0 10.147.8.1

Paresh Patel

Do you have route to 10.145.8.2 pointing to 10.0.3.2 on the far side? Your routing on the side from which you have posted config looks OK.

Also, can you ping 10.3.0.1?

jmenze

ASKER

no i cant not ping or traceroute so your saying i should put my route in 10.147.8.241 router

like 10.147.8.2 255.255.255.255 10.3.0.1 ??

Paresh Patel

Hi jmenze

Let's say you have router 1 (R1) and router 2 (R2).

----10.147.8.241---R1---10.0.3.2--------10.0.3.1----R2------90.0.0.2

On R1, you already have route for 90.0.0.0 255.255.255.0 pointing to 10.0.3.1

So do the following and let me know if you can successfully ping it.

1. From R1, ping 10.0.3.1.
2. From R2, ping 10.0.3.2.

if you can, check configuration on R2. Do you have route for 10.147.8.0 255.255.255.0 pointing to 10.0.3.1?

jmenze

ASKER

yes i can ping both

jmenze

ASKER

i think i would need 10.147.8.0 255.255.255.0 to point to 10.0.3.2

ASKER CERTIFIED SOLUTION

Paresh Patel

membership

This solution is only available to members.

To access this solution, you must be a member of Experts Exchange.

Start Free Trial

jmenze

ASKER

that didnt thanks for your hepl have a good day.