Solved

SolidWorks 2010 is saving slow

Posted on 2010-08-19
8
2,760 Views
Last Modified: 2013-12-04
Hi.

We have Clients using SolidWorks 2010.
All drawings are stored on a networkshare. The users are opening and saving directely on the network share.

But one client is using Windows 7 64bit and when he is saving a drawing it takes very long time!
it can take up to 30 seconds to save a little simple file. All clients are running 1gbps wich is running fine.

Users with Windows XP sp3 32bit is working fine with the save function.
users with WIndows XP sp2 64bit is working fine with the save function.

Any ideas to a solution?

best regards
0
Comment
Question by:Montesdatasystemer
  • 2
  • 2
  • 2
8 Comments
 
LVL 18

Expert Comment

by:centerv
ID: 33493509
have you checked the requirements and updates?

http://www.solidworks.com/sw/support/SystemRequirements.html 
0
 
LVL 61

Expert Comment

by:gheist
ID: 33494427
Antivirus software and "opportunistic locking" causes serious network speed issues for uncommon file formats.
ask google for oplocks in site:.microsoft.com

first disable client side, then server side if it helped.
0
 

Author Comment

by:Montesdatasystemer
ID: 33498515
Hi.

All requirements and updates is ok from Solid Works.

We are using Microsoft Forefront. And i allso tried to disable that without any difference.

It only goes slow when i am saving from inside the program Solid Works.

When i copy the same data as i just saved it goes very fast, So the problem is only through Solid.

Any other ideas?
0
Complete VMware vSphere® ESX(i) & Hyper-V Backup

Capture your entire system, including the host, with patented disk imaging integrated with VMware VADP / Microsoft VSS and RCT. RTOs is as low as 15 seconds with Acronis Active Restore™. You can enjoy unlimited P2V/V2V migrations from any source (even from a different hypervisor)

 
LVL 18

Expert Comment

by:centerv
ID: 33500941
Checking with company support or reinstalling would be my only other input.
0
 
LVL 61

Expert Comment

by:gheist
ID: 33501044
SolidWorks support bulletin:

Nov 03, 2009         Why might SolidWorks 2010 (or SolidWorks Explorer 2010) not start after rebooting the computer?

This is a known issue that only appears under the following conditions:
Microsoft Windows® XP 32-bit + specific Data Execution Prevention (DEP) settings.
The problem has been submitted to the SolidWorks Development team with the SPR below:
SPR 524232: SolidWorks 2010 no longer starts after the computer has been restarted. Note that using another user account to start SolidWorks via Run As allows SolidWorks to start until next reboot...
 
The workaround to this is as follows:
1. Right Mouse Button on My Computer and select Properties
2. On the Advanced tab>Performance>click Settings
3. Go to the Data Execution Prevention tab and most likely the setting "Turn on DEP for all programs and services except those I select" will be active
4. In the exception list see if Windows Explorer (explorer.exe) is listed. If it is, then select it and choose to Remove it from the list
5. OK out of all settings windows and reboot.
 
Special case:
When doing Step 3 above if the user currently has the option "Turn on DEP for essential Windows programs and services only" active, then do these alternate steps:
4. Toggle the other DEP option on so the list of possibly previously specified exceptions can be accessed
5. If Windows Explorer is in that exceptions list, then do the following process:
     a. Remove Windows Explorer from the list
     b. Reboot
     c. Go back in the DEP interface again and set the option back to “Turn on DEP for essential Windows programs and services only"
     d. Reboot once more.
0
 

Accepted Solution

by:
Montesdatasystemer earned 0 total points
ID: 33539339
After trying all possible opportunities posted with no luck, we talked with Solid Works Support,

They had som opportunities but it doesnt solve the problem. XP x64 again
0

Featured Post

Superior storage. Superior surveillance.

WD Purple drives are built for 24/7, always-on, high-definition security systems. With support for up to 8 hard drives and 32 cameras, WD Purple drives are optimized for surveillance.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Remote Apps is a feature in server 2008 which allows users to run applications off Remote Desktop Servers without having to log into them to run the applications.  The user can either have a desktop shortcut installed or go through the web portal to…
In this article, we will see the basic design consideration while designing a Multi-tenant web application in a simple manner. Though, many frameworks are available in the market to develop a multi - tenant application, but do they provide data, cod…
This Micro Tutorial will teach you how to censor certain areas of your screen. The example in this video will show a little boy's face being blurred. This will be demonstrated using Adobe Premiere Pro CS6.
As a trusted technology advisor to your customers you are likely getting the daily question of, ‘should I put this in the cloud?’ As customer demands for cloud services increases, companies will see a shift from traditional buying patterns to new…

861 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

22 Experts available now in Live!

Get 1:1 Help Now