Solved

How to configure Dreytek vigour 2801 router for ADSL?

Posted on 2010-08-20
7
480 Views
Last Modified: 2013-12-14
My company's adsl llink was upgraded recently, and lot of changes in term of settings. I need to change it, as according to my ISP, the following settings need to apply:

           Encapsulation: aal5snap
           vpi/vci: 8/35
           RFC 1483

           WAN IP
           My company: a.a.a.b
           ISP: a.a.a.a
           mask: 255.255.255.0252

            LAN IP
            c.c.c.240 - c.c.c.255
            mask 255.255.255.240

How to set them in my router?
0
Comment
Question by:Balack
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 5
  • 2
7 Comments
 

Author Comment

by:Balack
ID: 33490276
I'm not familiar with the above router. But, I did check, not option "aal5snap" is available.
0
 
LVL 62

Expert Comment

by:☠ MASQ ☠
ID: 33492293
Yes, here's the manual - you need to set the protocol as LLC/SNAP
0
 

Author Comment

by:Balack
ID: 33494036
Hi Masqueraid, can you show me step-by-step, thanks.
0
Supports up to 4K resolution!

The VS192 2-Port 4K DisplayPort Splitter is perfect for anyone who needs to send one source of DisplayPort high definition video to two or four DisplayPort displays. The VS192 can split and also expand DisplayPort audio/video signal on two or four DisplayPort monitors.

 
LVL 62

Accepted Solution

by:
☠ MASQ ☠ earned 500 total points
ID: 33494488
If you follow the stages through the manual it's explained quite well.
Make sure you have the logon credentials (username & password) for ADSL access.
Connect the ADSL line and the PC you are going to use to set up the router
Use the browser on the PC to log into the router by browsing to 192.168.1.1
Run the Quick Start Wizard & use the login information, make sure you select PPPoE LLC/SNAP as the protocol to be used
Save those changes.
That completes the first part of your requirement ( Encapsulation: aal5snap, vpi/vci: 8/35)

Next you need to change the Fixed IP address setting for the connection to "Yes" and setting the WAN address, your provider should also have given you external DNS server addresses.  It sounds from your list that you need to set the ISP IP address and then set the Company IP as an alias.  Check with your provider which way 'round.
Then set up MPoA (this is the RFC 1483 part of your requirement)
Once you have that done you then should have a connection to the Company WAN and just need to set the IP addresses for machines that are behind the Vigor
 
0
 

Author Comment

by:Balack
ID: 33495228
ok, I'll try it out...
0
 

Author Comment

by:Balack
ID: 33538741
It doesn't work as the line is not ADSL, instead, it is G.SHDL line. So the above Dreytek router doesn't support.

Now, we decided to get Draytek 2920. Do you have a configuration for G.SHDL? What alternative Cisco router can support G.SHDL line?
0
 

Author Closing Comment

by:Balack
ID: 34146570
ok
0

Featured Post

On Demand Webinar - Networking for the Cloud Era

This webinar discusses:
-Common barriers companies experience when moving to the cloud
-How SD-WAN changes the way we look at networks
-Best practices customers should employ moving forward with cloud migration
-What happens behind the scenes of SteelConnect’s one-click button

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Sometimes you have to pull out old tricks to get a new firewall to work… While we were installing a new Sonicwall at a customers site we found that sites they were able to visit before were not working.  It seemed random and we could not understa…
In the world of WAN, QoS is a pretty important topic for most, if not all, networks. Some WAN technologies have QoS mechanisms built in, but others, such as some L2 WAN's, don't have QoS control in the provider cloud.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Suggested Courses
Course of the Month8 days, 10 hours left to enroll

615 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question