Solved

Dial up to cisco router to make remotely configuration ?

Posted on 2010-08-21
1
537 Views
Last Modified: 2012-05-10

Hi Cisco Experts:

I have Cisco Router 2811

and this router has Module ( NM - 8AM -V2 //8 Port analog modem network module with V9.2//

and i need to enter this router from another site using dialup connection

how i can do that ...

Please advice me with proper configuration

please i need step by step



Thanks
0
Comment
Question by:Muhammed-Rummaneh
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
1 Comment
 
LVL 24

Accepted Solution

by:
rfc1180 earned 500 total points
ID: 33493507
This should get you going:

Also, you should consider Cisco best practices for routers (Initial configuration and hardening)

username junipersucks password ciscorocks

!Usernames for local authentication of the call.
!The client presents the username/password and the NAS

ip subnet-zero
no ip domain-lookup
ip domain-name domain.com

async-bootp dns-server 4.2.2.2
 
! --  Specifies (for async clients) the IP address of dns-server.

interface Loopback0
ip address 10.10.10.10 255.255.255.0

interface fast0/0
ip address y.y.y.y z.z.z.z

!y.y.y.y z.z.z.z is based on your directly connected on your interface into your network; update !accordingly.

! <<--Unused interfaces have been omitted.

interface Group-Async1
ip unnumbered Loopback0
encapsulation ppp
dialer in-band
dialer idle-timeout 600

dialer-group 1

!Apply interesting traffic definition from dialer-list 1.


async mode interactive
peer default ip address pool DIALIN

!Clients are assigned addresses from the ip address pool named "DIALIN".

ppp authentication chap
group-range 1 8

ip local pool DIALIN 10.20.20.1 10.20.20.10

!IP address pool for dialin clients.

ip classless
ip route 0.0.0.0 0.0.0.0 x.x.x.x

!x.x.x.x is your default gateway

dialer-list 1 protocol ip permit

!Specifies all IP traffic as interesting. Interesting traffic

line con 0
password ciscorocks
line 1 8

!TTY lines for the NM-8AM Modems.

modem InOut

! -- Support incoming and outgoing modem calls.

transport input all
autoselect ppp

!Launch PPP if PPP packets are detected. This is used in conjunction
!with async mode interactive under the group-async configuration.

flowcontrol hardware
line aux 0
line vty 0 4
login
password ciscorocks


Billy
0

Featured Post

Connect further...control easier

With the ATEN CE624, you can now enjoy a high-quality visual experience powered by HDBaseT technology and the convenience of a single Cat6 cable to transmit uncompressed video with zero latency and multi-streaming for dual-view applications where remote access is required.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
VTP servers with 3650 switches 5 54
Configure BGP 22 57
Can't access router with user and pass 10 108
Cisco 2911 Router - slow download speeds but very fast upload speeds 5 76
Problem Description:   Couple of months ago we upgraded the ADSL line at our branch office from Home to Business line. The purpose of transforming the service to have static public IP’s. We were in need for public IP’s to publish our web resour…
How to set-up an On Demand, IPSec, Site to SIte, VPN from a Draytek Vigor Router to a Cyberoam UTM Appliance. A concise guide to the settings required on both devices
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

732 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question