Solved

Cisco 2610XM Stun Configuration Not Working?

Posted on 2010-08-27
2
776 Views
Last Modified: 2012-08-13
Hi All,

We have been asked to build a config and apply them to a pair of Cisco 2610XM with 2 x WIC2T Cards over Serial using STUN. We have the configs perfectly built using templates from other successful installations of the same design. We didn't configure these other sites, but they are all working fine.

However the 2 Cisco 2610XM's we have received will not accept the simplest of STUN commands:

stun peer-name x.x.x.x
stun protocol-group 1 basic

It doesn't seem to recognise the STUN command. I also can't see STUN as a configurable option in the available list of commands when I press "?" under configuration mode...

Here is a copy of the show ver for the boxes:

-----------------------------------------------------------------------------------------------------------------
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.2(37), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Thu 15-Jun-06 20:48 by pwade
Image text-base: 0x8000808C, data-base: 0x80A1ED58

ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)

Router uptime is 6 minutes
System returned to ROM by power-on
System image file is "flash:c2600-i-mz.122-37.bin"

cisco 2610XM (MPC860P) processor (revision 0x200) with 126976K/4096K bytes of me
mory.
Processor board ID JAE08082YT5 (3612219116)
M860 processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
49152K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102
-----------------------------------------------------------------------------------------------------------------

Do i need to enable something seperate for STUN to engage?

Thanks
0
Comment
Question by:bmsbyrne
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
2 Comments
 
LVL 4

Accepted Solution

by:
erik_nodland earned 500 total points
ID: 33540418
Hi There

You will need at least an IP Plus feature set in order to configure STUN. It appears from the output that you only have an IP only feature set. Sorry it wasn't the anwser you were hoping for. You might be able to talk to your maintenance provider in order to give you the IP Plus IOS otherwise there will be a cost in upgrading.

Thanks
Erik
0
 

Author Comment

by:bmsbyrne
ID: 33545750
Hi Erik,

About two seconds after posting the question, we discovered this! Thanks for your prompt reply though.

Regards
0

Featured Post

Industry Leaders: We Want Your Opinion!

We value your feedback.

Take our survey and automatically be enter to win anyone of the following:
Yeti Cooler, Amazon eGift Card, and Movie eGift Card!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
IPv6 question 1 55
How to choose hardware firewall 5 85
Simple Phone Dialer for Win10 2 86
Understanding Extended-Access List 6 40
In the world of WAN, QoS is a pretty important topic for most, if not all, networks. Some WAN technologies have QoS mechanisms built in, but others, such as some L2 WAN's, don't have QoS control in the provider cloud.
Skype is a P2P (Peer to Peer) instant messaging and VOIP (Voice over IP) service – as well as a whole lot more.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

730 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question