Solved

SCCM and Image X pc capture

Posted on 2010-08-27
4
1,039 Views
Last Modified: 2013-11-21
Hi,

I don't want to use SCCM build and capture for this scenario. I want to boot using WinPE, use Image X to upload the WIMs to a share and deploy the WIMs using SCCM. The WIMs will also be sent to a manufacturer for imaging the new clients.

So far I have built my reference Desktop and Laptop. The Laptop has 2 partitions, 2GB for bit locker and the remaining for the installation and apps.

I have created 2 WinPE boot CDs with drivers for both computers. Next step is to run sysprep and then use Image X.

My question is how will I handle the 2 partitions on the Laptop ? Will Image X have to create 2 WIMs for the Laptop since it has 2 partitions ?

If that is the case would it be possible to create a WIM for the C Partition on the Laptop and then use a task sequence in SCCM for deployment, and partition the Laptop's hard-drive, make the 2 GB partition Primary and bootable and then install the WIM into the C partition ?

Now for the manufacturer....They will accept WIMs....Could I do the same and give them a WIM for the Laptop C partition and get them to create the partitions as they can do the partitioning also ?

Make sense ??



0
Comment
Question by:davewex
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
  • 2
4 Comments
 
LVL 31

Expert Comment

by:merowinger
ID: 33541458
Yes you've to create to capture wim files. But if you want you can put e.g. the D:\ partition wim file into the C:\ partition wim file and point the SCCM Task Sequence to the D:\ drive wim file ;)
0
 

Author Comment

by:davewex
ID: 33542964
Could you explain that a bit more please ?
0
 
LVL 31

Accepted Solution

by:
merowinger earned 100 total points
ID: 33549072
You're creating to wim files. ON for the C:\ and one for the D:\ partition.
In your SCCM Task Sequence you now create two partitions for both images.
Then you apply the operating system by applying the first wim file (path on your distribution point). You could now apply the second wim file also from your distribution point, or you already copied the second wim file into your first wim file and apply it from the local path
0
 

Author Closing Comment

by:davewex
ID: 33554138
gotcha
0

Featured Post

Free NetCrunch network monitor licenses!

Only on Experts-Exchange: Sign-up for a free-trial and we'll send you your permanent license!

Here is what you get: 30 Nodes | Unlimited Sensors | No Time Restrictions | Absolutely FREE!

Act now. This offer ends July 14, 2017.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Problem Description: Actually I found the below issue with some customers after migration from SMS 2003 to SCCM 2007 and epically if they change site code, some clients may appear in the console with old site code, plus old sites still appearing …
The question has been asked on multiple occasions as to how best to do printing in a remote desktop or terminal services environment.   It seems that this particular question has plagued several people and most especially as Terminal Services, as…
In this brief tutorial Pawel from AdRem Software explains how you can quickly find out which services are running on your network, or what are the IP addresses of servers responsible for each service. Software used is freeware NetCrunch Tools (https…
Monitoring a network: how to monitor network services and why? Michael Kulchisky, MCSE, MCSA, MCP, VTSP, VSP, CCSP outlines the philosophy behind service monitoring and why a handshake validation is critical in network monitoring. Software utilized …

728 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question