asked on

List switch ports on cisco switch 2800+ series

Hello,

Is there a way to list switch ports inside the switch. I can list the interfaces but this has alot of data I do not need. I am looking to just see (connected/unconnected), speed, port, and description. I have looked over several different commands but have been unsuccessful.

benofishal

Enter the command SHOW PORT - that should do the trick.

Andre Thibodeau

sh int status

tdog89

ASKER

For the show port it doesn't show nothing.

For the sh int status invalid command.

show ver:
Cisco WS-C2950-24
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA4, RELEASE SOFTWARE(fc1)

show commands available;

access-lists List access lists
arp Arp table
boot show boot attributes
cdp CDP information
clock Display the system clock
dtp DTP information
etherchannel EtherChannel information
flash: display information about flash: file system
history Display the session command history
hosts IP domain-name, lookup style, nameservers, and host table
interfaces Interface status and configuration
ip IP information
logging Show the contents of logging buffers
mac-address-table MAC forwarding table
mls Show MultiLayer Switching information
port-security Show secure port information
privilege Show current privilege level
processes Active process statistics
running-config Current operating configuration
sessions Information about Telnet connections
snmp snmp statistics
spanning-tree Spanning tree topology
startup-config Contents of startup configuration
storm-control Show storm control configuration
tcp Status of TCP connections
tech-support Show system information for Tech-Support
terminal Display terminal configuration parameters
users Display information about terminal lines
version System hardware and software status
vlan VTP VLAN status
vtp VTP information

benofishal

try SHOW MODULE - then SHOW PORT followed by a module number obtained from the first command.

tdog89

ASKER

No still didn't work correctly.

Here is what I am trying to display.

Port Name Status Vlan Level Duplex Speed Type
----- ------------------ ---------- ---------- ------ ------ ----- ------------
2/1 1 connected 7 normal a-full a-100 10/100BaseTX
2/2 2 connected 7 normal half 10 10/100BaseTX
2/3 3 connected 7 normal a-full a-100 10/100BaseTX
2/4 4 connected 7 normal full 10 10/100BaseTX
2/5 5 connected 7 normal a-full a-100 10/100BaseTX
2/6 6 connected 7 normal full 10 10/100BaseTX
2/7 7 connected 7 normal full 10 10/100BaseTX
2/8 8 connected 7 normal half 10 10/100BaseTX
2/9 9 connected 7 normal a-full a-100 10/100BaseTX
2/10 10 connected 7 normal a-full a-100 10/100BaseTX
2/11 11 connected 7 normal a-full a-100 10/100BaseTX
2/12 notconnect 7 normal auto auto 10/100BaseTX
2/13 notconnect 7 normal auto auto 10/100BaseTX
2/14 notconnect 7 normal auto auto 10/100BaseTX
2/15 notconnect 7 normal auto auto 10/100BaseTX
2/16 notconnect 7 normal auto auto 10/100BaseTX
2/17 notconnect 7 normal auto auto 10/100BaseTX
2/18 notconnect 7 normal auto auto 10/100BaseTX
2/19 notconnect 7 normal auto auto 10/100BaseTX

This is displayed from WS-C2948 Software, Version NmpSW: 8.4(9)GLX

I am trying to view this in IOS

ASKER CERTIFIED SOLUTION

benofishal

membership

This solution is only available to members.

To access this solution, you must be a member of Experts Exchange.

Start Free Trial

Andre Thibodeau

show interface status

you should get a result something like...

cat6513#show interface status
Port Name Status Vlan Duplex Speed
Po40 To tungsten-a e1b connected 42 a-full 10G
Po41 To tungsten-a e0b connected 42 a-full a-1000
Po41A connected 42 a-full a-1000
Po42 To tungsten-b e0a connected 42 a-full a-1000
Po42B connected 42 a-full a-1000
Po43 To tungsten-b e4c connected 42 a-full a-1000

AT