Dragon0x40
asked on
Upgrade IOS Cisco 6509 Switch
I have a Cisco 6509 switch with redundant 720/MSFC3 supervisors that needs the IOS upgraded to a newer version so I can install a line card WS-X6708-10GE in Slot 3.
I have new ios bin file: s72033-adventerprisek9_wan
These are my planned steps:
copy tftp: disk0:
**ip address x.x.x.x
**source file name: s72033-adventerprisek9_wan
**destination file name: s72033-adventerprisek9_wan
dir disk0:
boot system flash disk:0/s72033-adventerpris
reload (should I do a /verify?)
show version
show redundancy
show redundancy states
redundancy force-switchover (test the hot supervisor)
redundancy force-switchover (shift control back to primary supervisor)
#sh ver
Cisco Internetwork Operating System Software
IOS (tm) s72033_rp Software (s72033_rp-ENTSERVICESK9_W
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Tue 16-Aug-05 18:56 by kellmill
Image text-base: 0x40021040, data-base: 0x42B08000
ROM: System Bootstrap, Version 12.2(17r)S2, RELEASE SOFTWARE (fc1)
BOOTLDR: s72033_rp Software (s72033_rp-ENTSERVICESK9_W
uptime is 1 year, 2 weeks, 3 days, 20 hours, 42 minutes
Time since switched to active is 1 year, 2 weeks, 3 days, 20 hours, 46 minutes
System returned to ROM by unknown reload cause - suspect boot_data[BOOT_COUNT] 0x0, BOOT_COUNT 0, BOOTDATA 19 (SP by power-on)
System restarted at 14:17:49 pst Wed Sep 30 2009
System image file is "disk0:s72033-entservicesk
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco WS-C6509 (R7000) processor (revision 3.2) with 458720K/65536K bytes of memory.
Processor board ID xxxxxxxxxxx
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from power-on
SuperLAT software (copyright 1990 by Meridian Technology Corp).
X.25 software, Version 3.0.0.
Bridging software.
TN3270 Emulation software.
3 Virtual Ethernet/IEEE 802.3 interfaces
148 Gigabit Ethernet/IEEE 802.3 interfaces
16 Ten Gigabit Ethernet/IEEE 802.3 interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
#sh mod
Mod Ports Card Type Model Serial No.
--- ----- --------------------------
1 48 CEF720 48 port 1000mb SFP WS-X6748-SFP xxxxxxxxxxx
2 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE xxxxxxxxxxx
4 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE xxxxxxxxxxx
5 2 Supervisor Engine 720 (Active) WS-SUP720-BASE xxxxxxxxxxx
6 2 Supervisor Engine 720 (Hot) WS-SUP720-BASE xxxxxxxxxxx
7 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE xxxxxxxxxxx
8 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE xxxxxxxxxxx
9 48 48 port 10/100/1000mb EtherModule WS-X6148-GE-TX xxxxxxxxxxx
Mod MAC addresses Hw Fw Sw Status
--- --------------------------
1 xxxx.d88b.d10c to xxxx.d88b.d13b 1.12 12.2(14r)S5 12.2(18)SXE3 Ok
2 xxxx.553a.20a4 to xxxx.553a.20a7 2.7 12.2(14r)S5 12.2(18)SXE3 Ok
4 xxxx.f23e.2d1c to xxxx.f23e.2d1f 2.2 12.2(14r)S5 12.2(18)SXE3 Ok
5 xxxx.dae4.487c to xxxx.dae4.487f 3.3 8.1(3) 12.2(18)SXE3 Ok
6 xxxx.dae4.7790 to xxxx.dae4.7793 3.3 8.1(3) 12.2(18)SXE3 Ok
7 xxxx.a9f7.7cac to xxxx.a9f7.7caf 2.2 12.2(14r)S5 12.2(18)SXE3 Ok
8 xxxx.56f3.0c78 to xxxx.56f3.0c7b 2.5 12.2(14r)S5 12.2(18)SXE3 Ok
9 xxxx.125a.d5c8 to xxxx.125a.d5f7 1.1 7.2(1) 8.5(0.46)ROC Ok
Mod Sub-Module Model Serial Hw Status
--- --------------------------
1 Centralized Forwarding Card WS-F6700-CFC xxxxxxxxxxx 4.1 Ok
2 Centralized Forwarding Card WS-F6700-CFC xxxxxxxxxxx 4.0 Ok
4 Centralized Forwarding Card WS-F6700-CFC xxxxxxxxxxx 2.0 Ok
5 Policy Feature Card 3 WS-F6K-PFC3A xxxxxxxxxxx 2.5 Ok
5 MSFC3 Daughterboard WS-SUP720 xxxxxxxxxxx 2.5 Ok
6 Policy Feature Card 3 WS-F6K-PFC3A xxxxxxxxxxx 2.5 Ok
6 MSFC3 Daughterboard WS-SUP720 xxxxxxxxxxx 2.5 Ok
7 Centralized Forwarding Card WS-F6700-CFC xxxxxxxxxxx 2.0 Ok
8 Centralized Forwarding Card WS-F6700-CFC xxxxxxxxxxx 3.0 Ok
Mod Online Diag Status
--- -------------------
1 Pass
2 Pass
4 Pass
5 Pass
6 Pass
7 Pass
8 Pass
9 Pass
#sh mod 5
Mod Ports Card Type Model Serial No.
--- ----- --------------------------
5 2 Supervisor Engine 720 (Active) WS-SUP720-BASE xxxxxxxxxxx
Mod MAC addresses Hw Fw Sw Status
--- --------------------------
5 xxxx.dae4.487c to xxxx.dae4.487f 3.3 8.1(3) 12.2(18)SXE3 Ok
Mod Sub-Module Model Serial Hw Status
--- --------------------------
5 Policy Feature Card 3 WS-F6K-PFC3A xxxxxxxxxxx 2.5 Ok
5 MSFC3 Daughterboard WS-SUP720 xxxxxxxxxxx 2.5 Ok
Mod Online Diag Status
--- -------------------
5 Pass
I have new ios bin file: s72033-adventerprisek9_wan
These are my planned steps:
copy tftp: disk0:
**ip address x.x.x.x
**source file name: s72033-adventerprisek9_wan
**destination file name: s72033-adventerprisek9_wan
dir disk0:
boot system flash disk:0/s72033-adventerpris
reload (should I do a /verify?)
show version
show redundancy
show redundancy states
redundancy force-switchover (test the hot supervisor)
redundancy force-switchover (shift control back to primary supervisor)
#sh ver
Cisco Internetwork Operating System Software
IOS (tm) s72033_rp Software (s72033_rp-ENTSERVICESK9_W
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Tue 16-Aug-05 18:56 by kellmill
Image text-base: 0x40021040, data-base: 0x42B08000
ROM: System Bootstrap, Version 12.2(17r)S2, RELEASE SOFTWARE (fc1)
BOOTLDR: s72033_rp Software (s72033_rp-ENTSERVICESK9_W
uptime is 1 year, 2 weeks, 3 days, 20 hours, 42 minutes
Time since switched to active is 1 year, 2 weeks, 3 days, 20 hours, 46 minutes
System returned to ROM by unknown reload cause - suspect boot_data[BOOT_COUNT] 0x0, BOOT_COUNT 0, BOOTDATA 19 (SP by power-on)
System restarted at 14:17:49 pst Wed Sep 30 2009
System image file is "disk0:s72033-entservicesk
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco WS-C6509 (R7000) processor (revision 3.2) with 458720K/65536K bytes of memory.
Processor board ID xxxxxxxxxxx
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from power-on
SuperLAT software (copyright 1990 by Meridian Technology Corp).
X.25 software, Version 3.0.0.
Bridging software.
TN3270 Emulation software.
3 Virtual Ethernet/IEEE 802.3 interfaces
148 Gigabit Ethernet/IEEE 802.3 interfaces
16 Ten Gigabit Ethernet/IEEE 802.3 interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
#sh mod
Mod Ports Card Type Model Serial No.
--- ----- --------------------------
1 48 CEF720 48 port 1000mb SFP WS-X6748-SFP xxxxxxxxxxx
2 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE xxxxxxxxxxx
4 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE xxxxxxxxxxx
5 2 Supervisor Engine 720 (Active) WS-SUP720-BASE xxxxxxxxxxx
6 2 Supervisor Engine 720 (Hot) WS-SUP720-BASE xxxxxxxxxxx
7 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE xxxxxxxxxxx
8 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE xxxxxxxxxxx
9 48 48 port 10/100/1000mb EtherModule WS-X6148-GE-TX xxxxxxxxxxx
Mod MAC addresses Hw Fw Sw Status
--- --------------------------
1 xxxx.d88b.d10c to xxxx.d88b.d13b 1.12 12.2(14r)S5 12.2(18)SXE3 Ok
2 xxxx.553a.20a4 to xxxx.553a.20a7 2.7 12.2(14r)S5 12.2(18)SXE3 Ok
4 xxxx.f23e.2d1c to xxxx.f23e.2d1f 2.2 12.2(14r)S5 12.2(18)SXE3 Ok
5 xxxx.dae4.487c to xxxx.dae4.487f 3.3 8.1(3) 12.2(18)SXE3 Ok
6 xxxx.dae4.7790 to xxxx.dae4.7793 3.3 8.1(3) 12.2(18)SXE3 Ok
7 xxxx.a9f7.7cac to xxxx.a9f7.7caf 2.2 12.2(14r)S5 12.2(18)SXE3 Ok
8 xxxx.56f3.0c78 to xxxx.56f3.0c7b 2.5 12.2(14r)S5 12.2(18)SXE3 Ok
9 xxxx.125a.d5c8 to xxxx.125a.d5f7 1.1 7.2(1) 8.5(0.46)ROC Ok
Mod Sub-Module Model Serial Hw Status
--- --------------------------
1 Centralized Forwarding Card WS-F6700-CFC xxxxxxxxxxx 4.1 Ok
2 Centralized Forwarding Card WS-F6700-CFC xxxxxxxxxxx 4.0 Ok
4 Centralized Forwarding Card WS-F6700-CFC xxxxxxxxxxx 2.0 Ok
5 Policy Feature Card 3 WS-F6K-PFC3A xxxxxxxxxxx 2.5 Ok
5 MSFC3 Daughterboard WS-SUP720 xxxxxxxxxxx 2.5 Ok
6 Policy Feature Card 3 WS-F6K-PFC3A xxxxxxxxxxx 2.5 Ok
6 MSFC3 Daughterboard WS-SUP720 xxxxxxxxxxx 2.5 Ok
7 Centralized Forwarding Card WS-F6700-CFC xxxxxxxxxxx 2.0 Ok
8 Centralized Forwarding Card WS-F6700-CFC xxxxxxxxxxx 3.0 Ok
Mod Online Diag Status
--- -------------------
1 Pass
2 Pass
4 Pass
5 Pass
6 Pass
7 Pass
8 Pass
9 Pass
#sh mod 5
Mod Ports Card Type Model Serial No.
--- ----- --------------------------
5 2 Supervisor Engine 720 (Active) WS-SUP720-BASE xxxxxxxxxxx
Mod MAC addresses Hw Fw Sw Status
--- --------------------------
5 xxxx.dae4.487c to xxxx.dae4.487f 3.3 8.1(3) 12.2(18)SXE3 Ok
Mod Sub-Module Model Serial Hw Status
--- --------------------------
5 Policy Feature Card 3 WS-F6K-PFC3A xxxxxxxxxxx 2.5 Ok
5 MSFC3 Daughterboard WS-SUP720 xxxxxxxxxxx 2.5 Ok
Mod Online Diag Status
--- -------------------
5 Pass
ASKER
Requirments for memory:
ADVANCED ENTERPRISE SERVICES SSH
s72033-adventerprisek9_wan
Release Date: 15/Mar/2010
Size: 78535.54 KB (80420388 bytes)
Minimum Memory: DRAM:512 MB Flash:512 MB
What I have:
"sh ver" shows dram as 458720K/65536K bytes of memory. 458720k used plus 65536k free and divide total by 1024 comes out to 511.96 or 512mb of DRAM
"sh ver" shows flash as 65536K bytes of Flash. Divide 65536 by 1024 and I get 64mb of flash and that is why I have to use disk0: with a 512 mb PCMCIA card inserted.
Why is the requirement for flash 512mb when the ios is only 76 mb?
There is only 2mb of nvram?
#dir nvram:
Directory of nvram:/
1918 -rw- 24845 <no date> startup-config
1919 ---- 24 <no date> private-config
1920 -rw- 24845 <no date> underlying-config
1 ---- 4 <no date> rf_cold_starts
2 ---- 20 <no date> persistent-data
3 -rw- 0 <no date> ifIndex-table
1964024 bytes total (1936031 bytes free)
ADVANCED ENTERPRISE SERVICES SSH
s72033-adventerprisek9_wan
Release Date: 15/Mar/2010
Size: 78535.54 KB (80420388 bytes)
Minimum Memory: DRAM:512 MB Flash:512 MB
What I have:
"sh ver" shows dram as 458720K/65536K bytes of memory. 458720k used plus 65536k free and divide total by 1024 comes out to 511.96 or 512mb of DRAM
"sh ver" shows flash as 65536K bytes of Flash. Divide 65536 by 1024 and I get 64mb of flash and that is why I have to use disk0: with a 512 mb PCMCIA card inserted.
Why is the requirement for flash 512mb when the ios is only 76 mb?
There is only 2mb of nvram?
#dir nvram:
Directory of nvram:/
1918 -rw- 24845 <no date> startup-config
1919 ---- 24 <no date> private-config
1920 -rw- 24845 <no date> underlying-config
1 ---- 4 <no date> rf_cold_starts
2 ---- 20 <no date> persistent-data
3 -rw- 0 <no date> ifIndex-table
1964024 bytes total (1936031 bytes free)
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
ASKER
thanks mikebernhardt,
I successfully upgraded the IOS on both supervisors today.
These IOS images are 70 to 75 mb and I only calculate 62.5mb total (65536000 divided by 1024 two times) in sup-bootflash.
#dir sup-bootflash:
Directory of sup-bootflash:/
1 -rwx 30660760 Oct 6 2005 23:04:03 -07:00 s72033-ps-mz.122-17d.SXB7.
65536000 bytes total (34875112 bytes free)
I successfully upgraded the IOS on both supervisors today.
These IOS images are 70 to 75 mb and I only calculate 62.5mb total (65536000 divided by 1024 two times) in sup-bootflash.
#dir sup-bootflash:
Directory of sup-bootflash:/
1 -rwx 30660760 Oct 6 2005 23:04:03 -07:00 s72033-ps-mz.122-17d.SXB7.
65536000 bytes total (34875112 bytes free)
ASKER
I used this procedure to walk me through the entire process.
http://www.cisco.com/en/US/products/hw/switches/ps708/products_configuration_example09186a0080116ff0.shtml
http://www.cisco.com/en/US/products/hw/switches/ps708/products_configuration_example09186a0080116ff0.shtml
ASKER
#dir disk0:
Directory of disk0:/
1 -rw- 74273252 Oct 6 2005 23:10:34 -07:00 s72033-entservicesk9_wan-m
512065536 bytes total (437788672 bytes free)
I divided 512065536 by a 1024 twice and got 488mb total and divided 427788672 by 1024 twice and got 417 free. So 488 minus 417 tells me that the current IOS is about 71mb and the new IOS is 76 mb so they both shold fit.