How do I configure a Pix 506E 6.3.5 with a VLAN for Internet access only (i.e. guest WAP)

How do I setup a VLAN my Pix 506E 6.3.5 for Internet access only (i.e. guest WAP).

My current config:

PIX Version 6.3(5)
interface ethernet0 auto
interface ethernet1 auto
nameif ethernet0 outside security0
nameif ethernet1 inside security100
access-list 102 permit ip 10.1.1.0 255.255.255.0 10.1.3.0 255.255.255.0
access-list outside permit icmp any any
ip address outside 173.164.xxx.xxx 255.255.255.248
ip address inside 10.1.1.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool vpn-pool 10.1.3.100-10.1.3.200
global (outside) 1 interface
nat (inside) 0 access-list 102
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
access-group outside in interface outside
route outside 0.0.0.0 0.0.0.0 173.164.xxx.xxx 1
BMaenpaaAsked:
Who is Participating?
I wear a lot of hats...

"The solutions and answers provided on Experts Exchange have been extremely helpful to me over the last few years. I wear a lot of hats - Developer, Database Administrator, Help Desk, etc., so I know a lot of things but not a lot about one thing. Experts Exchange gives me answers from people who do know a lot about one thing, in a easy to use platform." -Todd S.

Cheever000Commented:
I think the command is

interface ethernet2 vlan1 physical
interface ethernet2 vlan2 logical


which makes VLAN 1 the native vlan and the VLAN 2 an extra VLAN.

and configure the nameifs for the interfaces as

nameif vlan2 Guest security50

or something really similar.
BMaenpaaAuthor Commented:
Thanks for your help. But do you mean ethernet1? I don't have an ethernet2 interface on this model pix, there are only two physical ports, ethernet0 and ethernet1.
Cheever000Commented:
Yes, sorry I miss typed that, I was thinking second interface and typed 2 forgetting we number at 0
Angular Fundamentals

Learn the fundamentals of Angular 2, a JavaScript framework for developing dynamic single page applications.

BMaenpaaAuthor Commented:
I tried that:

interface ethernet1 vlan1 physical
interface ethernet1 vlan2 logical

And lost all connectivity to, had to connect to console cable to take it back out. Any other suggestions?
Cheever000Commented:
If you are connected via telnet you can't complete the config after creating the VLANs you need to either do it via console or make the changes to the config in a text editor and copy it to start up then reload, as the interface will be changed with out IP addresses and or being associated to nameifs.  Just connect Via console and complete it all the way including the commands like this

nameif vlan2 Guest security50

then make sure the switch port is trunking and it should all be working correctly.

Experts Exchange Solution brought to you by

Your issues matter to us.

Facing a tech roadblock? Get the help and guidance you need from experienced professionals who care. Ask your question anytime, anywhere, with no hassle.

Start your 7-day free trial
BMaenpaaAuthor Commented:
I don't know what I would do without this forum. Thanks much B^)
It's more than this solution.Get answers and train to solve all your tech problems - anytime, anywhere.Try it for free Edge Out The Competitionfor your dream job with proven skills and certifications.Get started today Stand Outas the employee with proven skills.Start learning today for free Move Your Career Forwardwith certification training in the latest technologies.Start your trial today
Software Firewalls

From novice to tech pro — start learning today.