Want to win a PS4? Go Premium and enter to win our High-Tech Treats giveaway. Enter to Win

x
?
Solved

Connecting a Cisco 2600 to TW Telecom

Posted on 2010-11-18
4
Medium Priority
?
1,105 Views
Last Modified: 2012-05-10
We are moving from a DS3 to TW Telecom. I have been working on configuring a router to connect between our Juniper SSG and TW due to the way they did our IP blocks. I have configured both ethernet ports with a basic config just to pass traffic to our firewall. What is driving me nuts is that I can hit both ethernet ports from the outside. I can also ping our side of the ethernet from behind the firewall. Below is the config I am using:

interface FastEthernet0/0
 ip address <TW IP Block> 255.255.255.252
 speed 100
 full-duplex
!
interface Serial0/0
 no ip address
 encapsulation ppp
 shutdown
 no fair-queue
 ppp multilink
!
interface FastEthernet0/1
 ip address <our new IP block> 255.255.255.248
 speed 100
 full-duplex
!
interface Serial0/1
 no ip address
 encapsulation ppp
 shutdown
 ppp multilink
!
no ip http server
ip classless
ip route 0.0.0.0 0.0.0.0 <TW Telecom route>

0
Comment
Question by:Rodney Barnhardt
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 3
4 Comments
 
LVL 32

Author Comment

by:Rodney Barnhardt
ID: 34168158
Sorry. Also meant to add that from the outstide, that while I can hit both FE ports on the router, I cannot hit the port on the Juniper device. Also, while I can ping the FA0/1 port from behind the firewall, I cannot ping the FA0/0 port. This has to be some kind of routing problem, I just cannot figure it out.
0
 
LVL 1

Expert Comment

by:danielc25
ID: 34176923
Are you routing 0.0.0.0/0 on the FW to the IP of FE 0/1 on the 2600? Can you paste a show ip route?
0
 
LVL 32

Accepted Solution

by:
Rodney Barnhardt earned 0 total points
ID: 34177892
The problem ended up being in the firewall. I worked with TW support today and they confirmed the router was correct. I hade taken the code from a production NS25 and modified it for the SSG. I went back and recoded the config file and replaced it on the SSG. Everything came up and the problem was resolved.
0
 
LVL 32

Author Closing Comment

by:Rodney Barnhardt
ID: 34203799
I found the problem myself
0

Featured Post

Free Tool: IP Lookup

Get more info about an IP address or domain name, such as organization, abuse contacts and geolocation.

One of a set of tools we are providing to everyone as a way of saying thank you for being a part of the community.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

It happens many times that access list (ACL) have to be applied to outgoing router interface in order to limit some traffic.This article is about how to test ACL from the router which is not very intuitive for everyone. Below scenario shows simple s…
Getting hacked is no longer a matter or "if you get hacked" — the 2016 cyber threat landscape is now titled "when you get hacked." When it happens — will you be proactive, or reactive?
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Suggested Courses

604 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question