Solved

APPLE TIME CAPSULE

Posted on 2011-02-25
7
506 Views
Last Modified: 2012-05-11
I have purchased a Time Capsule | Trying.

I have given it an IP address, I can ping it, and get into and configure it.

However, I can get devices connected to it but no IP address is being delivered.

I have the DHCP side of things turned off as I do not want it to dole out IP addresses or be any router on my network.

What on earth do you need to do to this thing to make it work?
0
Comment
Question by:yostnet
  • 4
  • 3
7 Comments
 

Author Comment

by:yostnet
ID: 34985611
I already have a router and already have a server the doles out IP addresses.
0
 
LVL 53

Expert Comment

by:strung
ID: 34985642
I don't understand what you mean by "However, I can get devices connected to it but no IP address is being delivered."

If you don't want it to be set up as a DHCP server and your other router is connected to the internet, the TC should be set up in Bridge Mode.
0
 

Author Comment

by:yostnet
ID: 34985658
It is setup in bridge mode.

Bad terminology.

to connect it to my network | just use one of the ethernet ports?  Do I need a cross-over cable?
0
Resolve Critical IT Incidents Fast

If your data, services or processes become compromised, your organization can suffer damage in just minutes and how fast you communicate during a major IT incident is everything. Learn how to immediately identify incidents & best practices to resolve them quickly and effectively.

 
LVL 53

Expert Comment

by:strung
ID: 34985659
P.S. see attached screen shot.

Also, the IP address you assigned to the TC must be in the same subnet as your router, but outside the range used by the router's IP address. For instance, if the router is 192.168.3.1 and its DHCP server uses 192.168.3.100 to 192.168.3.150, set the TC to 192.168.3.2. (Gateway is 192.168.3.1, subnet mask 255.255.255.0)  See second screen shot.


0
 
LVL 53

Accepted Solution

by:
strung earned 500 total points
ID: 34985672
0
 
LVL 53

Expert Comment

by:strung
ID: 34985678
If it is in bridge mode, connect the WAN port to your network. The ethernet port is auto sensing - doesn't matter whether you use a cross over cable or not.
0
 

Author Closing Comment

by:yostnet
ID: 34985680
thx for the help
0

Featured Post

MIM Survival Guide for Service Desk Managers

Major incidents can send mastered service desk processes into disorder. Systems and tools produce the data needed to resolve these incidents, but your challenge is getting that information to the right people fast. Check out the Survival Guide and begin bringing order to chaos.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
iOS and VPN 6 163
Mac monitoring software? 6 98
Iphone 4S gone suddenly dead 6 70
Shortcomings of iPhone's text message feature 4 96
Hi Folks, This article is intended to throw some light or basically give an idea towards taking the first step in the world of Systems Administration. This would in the real context of the word "Systems Administration" which would mean right from…
Apple's line of laptop computers has made significant strides forward in the last few years. The biggest change being the switch to Intel processors in 2005. One thing about Apple hardware, especially that from a few years ago, is the tendency for i…
This Micro Tutorial hows how you can integrate  Mac OSX to a Windows Active Directory Domain. Apple has made it easy to allow users to bind their macs to a windows domain with relative ease. The following video show how to bind OSX Mavericks to …
CodeTwo Sync for iCloud (http://www.codetwo.com/sync-for-icloud?sts=6554) automatically synchronizes your Outlook 2016, 2013, 2010 or 2007 folders with iCloud folders available via iCloud Control Panel. This lets you automatically sync them with…

839 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question