Solved

using 2 DS1 interface devices to transport dsl

Posted on 2011-02-28
11
271 Views
Last Modified: 2012-08-13
Itrying to get internet to my location using the building owners existing network. they will lend me a ds-1 connection to another building where iI can order dsl and I will need to transport it over their "wire" to my device.

mydevice -----ds-1 --------network -----ds-1 ----- dsl modem
                                  <----  5 miles  ---->
                             
I have all the equipment neccessary just looking for help with best practice to forward the dsl service to my site.
0
Comment
Question by:cisco20
  • 4
  • 4
11 Comments
 
LVL 13

Expert Comment

by:kdearing
ID: 35001283
DSL limitation is 18,000' from the CO
Using an Ethernet Extender my be an option, but the best ones I've seen max out at 5km.
http://www.patton.com/products/pe_products.asp?category=146
0
 

Author Comment

by:cisco20
ID: 35001844
I misquoted , they will be providing a T1 connection between sites on their existing network infrastructure and it will be up to me to terminate and forward the adsl connection ( public ip )

0
 
LVL 13

Expert Comment

by:kdearing
ID: 35002286
I believe an unextended T1 max's out around 6000'

I can only think of 2 ways to go 5 miles without some kind of extender equipment:
1. fiber
2. RF (wireless)
0
 

Author Comment

by:cisco20
ID: 35002438
it is a fiber network.
0
Netscaler Common Configuration How To guides

If you use NetScaler you will want to see these guides. The NetScaler How To Guides show administrators how to get NetScaler up and configured by providing instructions for common scenarios and some not so common ones.

 
LVL 13

Expert Comment

by:kdearing
ID: 35002796
I assume the fiber terminates in an existing switch?
How far from the fiber to you?
0
 

Author Comment

by:cisco20
ID: 35011911
the distance limitations are not really an issue, I'm more concerned with the configuration to forward that ip through the point to point t1 circuit and terminating my device. The netrwork exists just not our own and will only be allowed that p to p connection for our solution.  
0
 
LVL 13

Expert Comment

by:kdearing
ID: 35032945
I don't know what to tell you.

It depends on what type of signal they're giving you:
Ethernet - Then you can use a switch or router
T1 - You'll need a router with a T1 card in it (or CSU/DSU)
DSL - You will need a DSL modem
0
 

Accepted Solution

by:
cisco20 earned 0 total points
ID: 35291812
Using isp modem in bridged mode and forwarding the public ip to the end device was the final solution.

Thanks.
0
 
LVL 68

Expert Comment

by:Qlemo
ID: 35339905
This question has been classified as abandoned and is being closed as part of the Cleanup Program. See my comment at the end of the question for more details.
0

Featured Post

Control application downtime with dependency maps

Visualize the interdependencies between application components better with Applications Manager's automated application discovery and dependency mapping feature. Resolve performance issues faster by quickly isolating problematic components.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Not able to route between subnets 8 104
stacking Catalyst 3650 20 36
Managed vs unmanaged switches 8 49
Mapping drives cross domain via logon script 2 11
In the hope of saving someone else's sanity... About a year ago we bought a Cisco 1921 router with two ADSL/VDSL EHWIC cards to load balance local network traffic over the two broadband lines we have, but we couldn't get the routing to work consi…
Data center, now-a-days, is referred as the home of all the advanced technologies. In-fact, most of the businesses are now establishing their entire organizational structure around the IT capabilities.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

864 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

21 Experts available now in Live!

Get 1:1 Help Now