No SIP Debug info

Posted on 2011-03-07
Medium Priority
Last Modified: 2012-05-11
I am trying to setup Cisco CME (UC540) to call to my Exchange server for voice mail.
When I call the VM extension I am getting NO debug with "debug ccsip messages".
But when I debug dial-peer I get debug and it appears to route to the correct dial-peer 2000.
Calling number is 260, VM is 777 and Dial Peer is 2000.  Any thoughts on how to debug this?  What determines which source address will be used by the UC540 to communicate with it ipv4: target IP?  I am thinking perhaps the UC540 is using the outside IP and that might not be getting tunneled correctly to get to the Exchange server.  Thanks.

002433: Mar  6 23:39:01.604: //-1/CDAA43BA8420/DPM/dpMatchPeersMoreArg:
   List of Matched Outgoing Dial-peer(s):
     1: Dial-peer Tag=2000
002434: Mar  6 23:39:01.608: //-1/CDAA43BA8420/RXRULE/regxrule_stack_push_RegXruleNumInfo_internal: stack=0x89F1EBCC; count=2
002435: Mar  6 23:39:01.608: //-1/CDAA43BA8420/RXRULE/regxrule_dp_translate: No profile found in peer 2000 for outgoing direction
002436: Mar  6 23:39:01.608: //-1/CDAA43BA8420/RXRULE/regxrule_dp_translate: calling_number=260 calling_octet=0x0
        called_number=777 called_octet=0x80
        redirect_number= redirect_type=0 redirect_plan=0        redirect_PI=0 redirect_SI=0
Question by:amigan_99
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
LVL 16

Expert Comment

ID: 35112188
. . . not in front of the console . . . but can't you configure the source IP address for specific services?

Good luck,

Accepted Solution

amigan_99 earned 0 total points
ID: 35140468
I found it:

voice service voip
   bind control source-interface BVI100           <<<<<<<<
   bind media source-interface BVI100            <<<<<<<<

Author Closing Comment

ID: 35174549
This was the piece I was seeking.

Featured Post

Visualize your virtual and backup environments

Create well-organized and polished visualizations of your virtual and backup environments when planning VMware vSphere, Microsoft Hyper-V or Veeam deployments. It helps you to gain better visibility and valuable business insights.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

I recently purchased a Bluetooth headset called the Music Jogger (model BSH10). The control buttons on it look like this: One of my goals is to use it as the microphone and speakers for Skype calls. In that respect, it works well. However, I …
Implementing Avaya's One-X portal is pretty painless, until you want to deploy this to the Android and iPhone clients when these clients are outside of your network. The clients will also work within your local network. Here is our experience and so…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

762 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question