Want to win a PS4? Go Premium and enter to win our High-Tech Treats giveaway. Enter to Win

x
?
Solved

Question in DSL Router

Posted on 2011-03-16
6
Medium Priority
?
347 Views
Last Modified: 2012-08-13
Hi , i have a DSL router from ATT&T and it was working just fine. After we wiped out the config and we entered it , workstations cannot get a valid IP , they get 169.254.x.y.
Any ideas ?

here is the config Current configuration : 3241 bytes
!
version 12.3
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
!
hostname dslrouter
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 debugging
logging console informational
enable secret 5 $1$5F0M$os66MKOMaptzg9jOdBP741
!
username admin privilege 15 secret 5 $1$EJXV$g1HiDSIIB/tMJZyww0lSN.
username llbladmin privilege 15 secret 5 $1$SWRx$hE9IHcpzBH8GhDr.otBl31
clock timezone PCTime -6
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
no aaa new-model
ip subnet-zero
no ip source-route
!
!
ip cef
!
!
ip tcp synwait-time 10
no ip bootp server
ip domain name sbcglobal.net
ip name-server 151.164.1.8
ip name-server 151.164.11.201
ip ips po max-events 100
vpdn enable
!
vpdn-group pppoe
 request-dialin
  protocol pppoe
!
no ftp-server write-enable
!
!
!
!
!
!
bba-group pppoe global
!
!
interface ATM0
 no ip address
 no ip redirects
 no ip unreachables
 no ip proxy-arp
 no atm ilmi-keepalive
 pvc 0/35
  protocol pppoe
 !
 dsl operating-mode auto
!
interface BRI0
 no ip address
 no ip redirects
 no ip unreachables
 no ip proxy-arp
 shutdown
 no cdp enable
!
interface FastEthernet0
 description $ES_LAN$$FW_INSIDE$$ETH-LAN$
 no ip address
 no ip redirects
 no ip unreachables
 no ip proxy-arp
 ip nat inside
 ip virtual-reassembly
 ip tcp adjust-mss 1452
 duplex auto
 speed auto
!
interface FastEthernet1
 no ip address
0
Comment
Question by:c_hockland
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 3
  • 3
6 Comments
 
LVL 13

Expert Comment

by:kdearing
ID: 35153247
DHCP is not set up.

Assuming this is a Cisco router, this link will show you how:
http://www.routergeek.net/content/view/37/37/

Cisco link:
http://www.cisco.com/en/US/docs/ios/12_2/ip/configuration/guide/1cfdhcp.html
0
 

Author Comment

by:c_hockland
ID: 35153253
it is a cisco router and it is plugged in porrt 4/38 on my core switch which is on the same vlan where my DHCP server is .
0
 
LVL 13

Expert Comment

by:kdearing
ID: 35153333
DHCP is handled by your server, OK
I also just noticed that NAT is not configured.

http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080094e77.shtml
0
Industry Leaders: We Want Your Opinion!

We value your feedback.

Take our survey and automatically be enter to win anyone of the following:
Yeti Cooler, Amazon eGift Card, and Movie eGift Card!

 

Author Comment

by:c_hockland
ID: 35153341
well , sbcglobal sent me these settings

dslrouter(dhcp-config)#network 65.66.117.225 255.255.255.0
dslrouter(dhcp-config)#dns-server 151.164.1.8
dslrouter(dhcp-config)#default-router 65.66.117.230
dslrouter(dhcp-config)#domain sbcglobal.net
dslrouter(dhcp-config)#end

so i added them and someone tomo morning will test ( this is a remote site)

now they gave me a range 65.66.117.225 - .229
and i am not sure if i entered it right.... actually i know i did wrong cause my subnet mask is /24
0
 

Author Comment

by:c_hockland
ID: 35153356
btw , it is
Cisco 1801 (MPC8500) processor (revision 0x200) with 118784K/12288K bytes of memory.
Processor board ID FHK09262006, with hardware revision 0000

9 FastEthernet interfaces
1 ISDN Basic Rate interface
1 ATM interface
31360K bytes of ATA CompactFlash (Read/Write)
0
 
LVL 13

Accepted Solution

by:
kdearing earned 2000 total points
ID: 35189678
Those are your static IP addresses.

The following link shows how to configure pppoe with nat
http://www.cisco.com/en/US/docs/routers/access/1800/1801/software/configuration/guide/pppoenat.html
0

Featured Post

Free Tool: IP Lookup

Get more info about an IP address or domain name, such as organization, abuse contacts and geolocation.

One of a set of tools we are providing to everyone as a way of saying thank you for being a part of the community.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

It happens many times that access list (ACL) have to be applied to outgoing router interface in order to limit some traffic.This article is about how to test ACL from the router which is not very intuitive for everyone. Below scenario shows simple s…
There are two basic ways to configure a static route for Cisco IOS devices. I've written this article to highlight a case study comparing the configuration of a static route using the next-hop IP and the configuration of a static route using an outg…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Suggested Courses

610 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question