?
Solved

Redistribution Between Two EIGRP Autonomous Systems

Posted on 2011-03-24
8
Medium Priority
?
1,027 Views
Last Modified: 2012-05-11
Hello experts,
I am trying to get EIGRP redistribution working between two organizations.  I set up the configuration as seen here but none of the routes from AS100 are being redistributed to AS104 & visa-versa.  Any ideas?

Thanks in advance.

EIGRP.jpg
0
Comment
Question by:SpokaneISD
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
8 Comments
 
LVL 17

Expert Comment

by:Marius Gunnerud
ID: 35212822
have you tried changing the metric?

so instead of having redistribute eigrp 100 metric 1 1 0 1 1 enter redistribute eigrp 100 metric 1 1 1 1 1.

The 0 you entered is for the value of reliability, though i have never tried entering 0 for any value before, I think it might be causing the issue.
0
 
LVL 6

Expert Comment

by:gcl_hk
ID: 35212906
I think you should add a secondary ip address between router interface, and assign to different AS, like this sample:

192.168.75.1 - RTR1 ---------------------------- RTR2 - 192.168.75.2
192.168.57.1   Secondary                                           192.168.57.2 Secondary

RTR1:
router eigrp 104
network 192.168.75.0
redistribute eigrp 100
router eigrp 100
network 192.168.57.0

RTR2:
router eigrp 100
network 192.168.57.0
redistribute eigrp 104
router eigrp 104
network 192.168.75.0
0
 
LVL 17

Expert Comment

by:Marius Gunnerud
ID: 35213920
There is no need for the secondary address as neighbors are only formed using the primary addresses, and data packets are sourced using the primary address. You only need to make sure that all networks that are required to communicate with eachother are correctly configured using the network command.

Also you are not required to enter the metric when redistributing eigrp into another eigrp process. This is mainly used when redistributing a different routing protocol into eigrp.
0
Veeam Disaster Recovery in Microsoft Azure

Veeam PN for Microsoft Azure is a FREE solution designed to simplify and automate the setup of a DR site in Microsoft Azure using lightweight software-defined networking. It reduces the complexity of VPN deployments and is designed for businesses of ALL sizes.

 
LVL 1

Expert Comment

by:rolledoats
ID: 35214332
You could always use BGP between the two routers, use EIGRP as the iBGP. Quite a simple config
0
 

Author Comment

by:SpokaneISD
ID: 35233088
I will change the reliability metric to 1 & retest later this week.  I'll post my results then. Thanks.
0
 

Accepted Solution

by:
SpokaneISD earned 0 total points
ID: 35471410
I have not been able to reschedule a test with the other organization.  I will have to cancel this for now & re-submit if necessary.
0
 

Author Closing Comment

by:SpokaneISD
ID: 35499811
I have been unable to schedule a re-test with the other organization.
0

Featured Post

Industry Leaders: We Want Your Opinion!

We value your feedback.

Take our survey and automatically be enter to win anyone of the following:
Yeti Cooler, Amazon eGift Card, and Movie eGift Card!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

There are two basic ways to configure a static route for Cisco IOS devices. I've written this article to highlight a case study comparing the configuration of a static route using the next-hop IP and the configuration of a static route using an outg…
In the world of WAN, QoS is a pretty important topic for most, if not all, networks. Some WAN technologies have QoS mechanisms built in, but others, such as some L2 WAN's, don't have QoS control in the provider cloud.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
In this brief tutorial Pawel from AdRem Software explains how you can quickly find out which services are running on your network, or what are the IP addresses of servers responsible for each service. Software used is freeware NetCrunch Tools (https…

650 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question