Solved

Configure Windows SNMP with VBscript

Posted on 2011-03-25
4
1,908 Views
Last Modified: 2012-05-11
Configure Windows SNMP with VBscript

I have an SNMP service to configure in 100 windows 2003 server.
I need a script that reads the name of the servers from a text file-- the names are lined up in a column-- and makes the change to the SNMP config for each server.

the Tabs and fields I need to modify are :

Agent Tab:
Service
Physical=checked
Applications=Checked
Datalink and subnetworks=checked
Internet=checked
End-to-end=checked

Traps Tab
Community name=public
Trap destination= 10.10.10.10

Security Tab:

Community
Public= Read Only
Private = Read Create

Accept SNMP packets from these hosts= selected
                 10.10.10.10




0
Comment
Question by:jskfan
  • 2
  • 2
4 Comments
 
LVL 3

Accepted Solution

by:
sam0x01 earned 500 total points
ID: 35229149
Save the below as a .reg file
Try importing this reg file into a test server with the same production SNMP settings.

If this corrupts the SNMP Settings, then I am unsure how this can be done.
Windows Registry Editor Version 5.00

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\SNMP\Parameters]
"EnableAuthenticationTraps"=dword:00000001
"NameResolutionRetries"=dword:00000010

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\SNMP\Parameters\PermittedManagers]
"1"="10.10.10.10"

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\SNMP\Parameters\RFC1156Agent]
"sysContact"=""
"sysLocation"=""
"sysServices"=dword:0000004f

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\SNMP\Parameters\TrapConfiguration]

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\SNMP\Parameters\TrapConfiguration\public]
"1"="10.10.10.10"

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\SNMP\Parameters\ValidCommunities]
"public"=dword:00000004

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\SNMP\Security]
"Security"=hex:01,00,14,80,b8,00,00,00,c4,00,00,00,14,00,00,00,30,00,00,00,02,\
  00,1c,00,01,00,00,00,02,80,14,00,ff,01,0f,00,01,01,00,00,00,00,00,01,00,00,\
  00,00,02,00,88,00,06,00,00,00,00,00,14,00,fd,01,02,00,01,01,00,00,00,00,00,\
  05,12,00,00,00,00,00,18,00,ff,01,0f,00,01,02,00,00,00,00,00,05,20,00,00,00,\
  20,02,00,00,00,00,14,00,8d,01,02,00,01,01,00,00,00,00,00,05,04,00,00,00,00,\
  00,14,00,8d,01,02,00,01,01,00,00,00,00,00,05,06,00,00,00,00,00,14,00,00,01,\
  00,00,01,01,00,00,00,00,00,05,0b,00,00,00,00,00,18,00,fd,01,02,00,01,02,00,\
  00,00,00,00,05,20,00,00,00,23,02,00,00,01,01,00,00,00,00,00,05,12,00,00,00,\
  01,01,00,00,00,00,00,05,12,00,00,00

Open in new window

0
 

Author Comment

by:jskfan
ID: 35340197
Thanks..
I tried it in my workstation and it worked just fine.

How do I deploy it to multiple computers without login into each computer?
0
 
LVL 3

Assisted Solution

by:sam0x01
sam0x01 earned 500 total points
ID: 35347451
You can run "regedit /s \\servername\share\path\filename.reg" or "reg /import as the command to import. Unfortunately neither regedit or reg /import allow to perform this remotely.

Suggest putting the .reg file on a shared resource and using psexec to perform this remotely. Psexec is a command that allows remote execution of tasks.

Make sure you try it on a single server before pushing it to the masses because it may behave unusually if there is prior SNMP config.

Alternative ways would be using the "AT" command to schedule once. Think schtasks also is in Windows 2003 Server.
0
 

Author Closing Comment

by:jskfan
ID: 35453213
thanks a lot
0

Featured Post

Netscaler Common Configuration How To guides

If you use NetScaler you will want to see these guides. The NetScaler How To Guides show administrators how to get NetScaler up and configured by providing instructions for common scenarios and some not so common ones.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Over the years I have built up my own little library of code snippets that I refer to when programming or writing a script.  Many of these have come from the web or adaptations from snippets I find on the Web.  Periodically I add to them when I come…
This article will show, step by step, how to integrate R code into a R Sweave document
The viewer will learn the basics of jQuery, including how to invoke it on a web page. Reference your jQuery libraries: (CODE) Include your new external js/jQuery file: (CODE) Write your first lines of code to setup your site for jQuery.: (CODE)
In this seventh video of the Xpdf series, we discuss and demonstrate the PDFfonts utility, which lists all the fonts used in a PDF file. It does this via a command line interface, making it suitable for use in programs, scripts, batch files — any pl…

947 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

22 Experts available now in Live!

Get 1:1 Help Now