David George
asked on
How to load an advanced Layer 3 IOS on CIsco 4506
Hi - I need to know if there is an advanced L3 IOS for this particular switch. I would like to do dynamic routing with it...
show ver
Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9K91S-M), Version
12.2(25)EWA14, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Tue 20-May-08 19:35 by chendah
Image text-base: 0x10000000, data-base: 0x115CE0AC
ROM: 12.2(20r)EW1
Dagobah Revision 226, Swamp Revision 34
Switch uptime is 7 minutes
System returned to ROM by power-on
System image file is "bootflash:cat4000-i9k91s- mz.122-25. EWA14.bin"
cisco WS-C4506 (MPC8245) processor (revision 10) with 262144K bytes of memory.
Processor board ID FOX07460xxx
MPC8245 CPU at 266Mhz, Supervisor II+
Last reset from PowerUp
1 Virtual Ethernet interface
240 FastEthernet interfaces
2 Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.
Configuration register is 0x2142
Switch#show mod
Chassis Type : WS-C4506
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.
---+-----+---------------- ---------- ---------- --+------- ---------- -+-------- ---
1 2 Supervisor II+ 1000BaseX (GBIC) WS-X4013+ JAExxxxxxxxx
2 48 10/100BaseTX (RJ45) WS-X4148-RJ JAExxxxxxxx
3 48 10/100BaseTX (RJ45) WS-X4148-RJ JAExxxxxxxx
4 48 10/100BaseTX (RJ45) WS-X4148-RJ JAExxxxxxxx
5 48 10/100BaseTX (RJ45) WS-X4148-RJ JAExxxxxxxx
6 48 10/100BaseTX (RJ45) WS-X4148-RJ JAExxxxxxxx
M MAC addresses Hw Fw Sw Status
--+----------------------- ---------+ ---+------ ------+--- ---------- ---+------ ---
1 000e.83a0.7800 to 000e.83a0.7801 4.1 12.2(20r)EW1 12.2(25)EWA14 Ok
2 0019.065a.ea60 to 0019.065a.ea8f 3.3 Ok
3 0014.69bd.88d0 to 0014.69bd.88ff 3.2 Ok
4 001e.7a2f.eba0 to 001e.7a2f.ebcf 3.4 Ok
5 000d.28c0.4f90 to 000d.28c0.4fbf 3.1 Ok
6 000d.28c0.5710 to 000d.28c0.573f 3.1 Ok
Chassis Type : WS-C4506
show ver
Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9K91S-M), Version
12.2(25)EWA14, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Tue 20-May-08 19:35 by chendah
Image text-base: 0x10000000, data-base: 0x115CE0AC
ROM: 12.2(20r)EW1
Dagobah Revision 226, Swamp Revision 34
Switch uptime is 7 minutes
System returned to ROM by power-on
System image file is "bootflash:cat4000-i9k91s-
cisco WS-C4506 (MPC8245) processor (revision 10) with 262144K bytes of memory.
Processor board ID FOX07460xxx
MPC8245 CPU at 266Mhz, Supervisor II+
Last reset from PowerUp
1 Virtual Ethernet interface
240 FastEthernet interfaces
2 Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.
Configuration register is 0x2142
Switch#show mod
Chassis Type : WS-C4506
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.
---+-----+----------------
1 2 Supervisor II+ 1000BaseX (GBIC) WS-X4013+ JAExxxxxxxxx
2 48 10/100BaseTX (RJ45) WS-X4148-RJ JAExxxxxxxx
3 48 10/100BaseTX (RJ45) WS-X4148-RJ JAExxxxxxxx
4 48 10/100BaseTX (RJ45) WS-X4148-RJ JAExxxxxxxx
5 48 10/100BaseTX (RJ45) WS-X4148-RJ JAExxxxxxxx
6 48 10/100BaseTX (RJ45) WS-X4148-RJ JAExxxxxxxx
M MAC addresses Hw Fw Sw Status
--+-----------------------
1 000e.83a0.7800 to 000e.83a0.7801 4.1 12.2(20r)EW1 12.2(25)EWA14 Ok
2 0019.065a.ea60 to 0019.065a.ea8f 3.3 Ok
3 0014.69bd.88d0 to 0014.69bd.88ff 3.2 Ok
4 001e.7a2f.eba0 to 001e.7a2f.ebcf 3.4 Ok
5 000d.28c0.4f90 to 000d.28c0.4fbf 3.1 Ok
6 000d.28c0.5710 to 000d.28c0.573f 3.1 Ok
Chassis Type : WS-C4506
ASKER CERTIFIED SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
SOLUTION
membership
This solution is only available to members.
To access this solution, you must be a member of Experts Exchange.
This question has been classified as abandoned and is closed as part of the Cleanup Program. See the recommendation for more details.