Solved

Dial Peer Question

Posted on 2011-09-09
3
357 Views
Last Modified: 2012-05-12
I have an existing dial peer:

dial-peer voice 4400 pots
 description Route to RightFAX
 destination-pattern 44[0-5].
 incoming called-number 44[0-5].
 direct-inward-dial
 port 0/1/0:23
 forward-digits all
!

I want to test with a new Rightfax server so I wanted to split one DID out of this and route it somewhere else so I created this:

dial-peer voice 4446 voip
 destination-pattern 4446
 session target ipv4:216.51.1.20
 incoming called-number 4446
 dtmf-relay h245-alphanumeric
 codec g711ulaw
 fax-relay ecm disable
 fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback none
 no vad

Doesnt it take the most specific one or I am thinking of something else?  Anyone know what I am doing wrong here because it is still routing to the old server.
0
Comment
Question by:mattpayne59
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
3 Comments
 
LVL 20

Expert Comment

by:José Méndez
ID: 36513200
You have it right according to (Non-DID Case): http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml#topic7

Try changing the chronological configuration order of the dial-peers:

no dial-peer voice 4400

dial-peer voice 4400 pots
 description Route to RightFAX
 destination-pattern 44[0-5].
 incoming called-number 44[0-5].
 direct-inward-dial
 port 0/1/0:23
 forward-digits all

This should put dialpeer 4400 at the bottom of the dial-peer list in the configuration file. Or, you can manually accommodate dialpeer 4400 below 4446, and then reload the configuration from a TFTP. Really, anything that will make the system read dialpeer 4446 first.
0
 

Author Comment

by:mattpayne59
ID: 36522950
Same thing happened once I changed the order.
0
 
LVL 20

Accepted Solution

by:
José Méndez earned 500 total points
ID: 36523721
Can you enable these:

debug voice dialpeer
debug isdn q931 --> if you have ISDN trunks
debug ccapi inou  -->

term mon  --> enable monitor logging

Reproduce the problem, capture the output and provide the calling number and called number.  Attach files to thread.
0

Featured Post

Independent Software Vendors: We Want Your Opinion

We value your feedback.

Take our survey and automatically be enter to win anyone of the following:
Yeti Cooler, Amazon eGift Card, and Movie eGift Card!

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Hey there Heard about jingle, the add on for XMPP that enables point to point audio between two XMPP clients. No server config necessary. Actually quite a cool feature. However, how good is it if you can not use those voice capabilities to do a P…
As companies replace their old PBX phone systems with Unified IP Communications, many are finding out that legacy applications such as fax do not work well with VoIP. Fortunately, Cloud Faxing provides a cost-effective alternative that works over an…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Suggested Courses

695 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question