Solved

Cisco QOS using Access Lists for Citrix and VOIP

Posted on 2011-09-19
3
1,367 Views
Last Modified: 2012-05-12
Hello,

I am in need of some help developing a QoS policy for my MPLS utilizing access lists to map to specfic qos values. I need to prioritize my Avaya IP Office phone system which i believe uses dscp 46 for the call and dscp 34 for signaling.

Along with that I am looking for help in prioritizing my Citrix Xenapp traffic, I have Xenapp5 and Xenapp6 servers.  Should this be done via port / protocol or via IP any suggestions?

The values my MPLS provider is said to support are:
EF-46 (Real Time)
AF-31(Critical)
AF-11(Priority)

Thank you.



0
Comment
Question by:nmatese
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
3 Comments
 
LVL 6

Expert Comment

by:Sanjeevloke
ID: 36565984
class-map match-any Application
 description Video Conference
 match ip dscp af31  --------------------dscp bit marked by application if u knoe.
match access-group name Application-------also u can use IP access-list to prioritize.

class-map match-any RTP
 description [ VOIP Audio ]
 match protocol rtp audio


interface GigabitEthernet0/2
des **** LAN Interface ****
service-policy input QOS-IN

policy-map QOS-IN
 description [ Re-Classify ]
 class RTP
  set dscp ef
 class Application
  set ip dscp af31

-------------------------------------------------------------------------------------------

interface GigabitEthernet0/2
des **** WAN Interface ****
service-policy output QOS-OUT


policy-map QOS-OUT
 class REAL-TIME
  priority percent 25
 class Application
  bandwidth percent 15

class-map match-any REAL-TIME
 description REAL-TIME Traffic
 match ip dscp ef

class-map match-any Application
 description Application
 match ip dscp af21

U can modify percentage as per ur requirement
0
 

Author Comment

by:nmatese
ID: 36566971
They provide me with the class matching, I need to use access lists to classify the other traffic. Citrix, Avaya IPOffice VOIP, SQL Servers,

Attached is the class match, the provider has given me.


Class-map: DSCP-EF-CLASS (match-all)
    dscp af41

Class-map: DSCP-AF31-CLASS (match-all)
    dscp af42

Class-map: DSCP-AF11-CLASS (match-all)
    dscp af43
Class-map: class-default (match-any)
    dscp default
A typical scheme (the default scheme):
•	Real Time QoS – Always prioritize over all other traffic; has a minimum guarantee of 100% bandwidth
•	Critical QoS – Always yield to Real Time traffic; has a minimum guarantee of 50% of the excess bandwidth unused by Real Time traffic 
•	Priority QoS – Always yield to Real Time traffic; has a minimum guarantee of 30% of the excess bandwidth unused by Real Time traffic 
•	Standard QoS – Always yield to Real Time traffic; has a minimum guarantee of 20% of the excess bandwidth unused by Real Time traffic

Open in new window

0
 
LVL 6

Accepted Solution

by:
Sanjeevloke earned 500 total points
ID: 36567092
Its OK for what they do it at there side.

U have to do as per ur requirement..

QOS config at LAN interface connected to switch..
!
class-map match-any RTP
 description [ VOIP Audio ]
 match protocol rtp audio
match access-group name Avaya
!!
class-map match-any Application
match ip dscp af31  
match access-group name Application
!
policy-map QOS-IN
 description [ Re-Classify ]
 class RTP
  set dscp af41
 class Application
  set ip dscp af42
!
interface GigabitEthernet0/2
des **** LAN Interface ****
service-policy input QOS-IN
----------------------------------------------------------
On WAN side

interface GigabitEthernet0/2
des **** WAN Interface ****
service-policy output QOS-OUT


policy-map QOS-OUT
 class REAL-TIME
  priority percent 25
 class Application
  bandwidth percent 15

class-map match-any REAL-TIME
 description REAL-TIME Traffic
 match ip dscp 41

class-map match-any Application
 description Application
 match ip dscp af42




!
0

Featured Post

Efficient way to get backups off site to Azure

This user guide provides instructions on how to deploy and configure both a StoneFly Scale Out NAS Enterprise Cloud Drive virtual machine and Veeam Cloud Connect in the Microsoft Azure Cloud.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Quality of Service (QoS) options are nearly endless when it comes to networks today. This article is merely one example of how it can be handled in a hub-n-spoke design using a 3-tier configuration.
As companies replace their old PBX phone systems with Unified IP Communications, many are finding out that legacy applications such as fax do not work well with VoIP. Fortunately, Cloud Faxing provides a cost-effective alternative that works over an…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

707 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question