Solved

IP Accounting on 3560 L3 switch?

Posted on 2011-09-20
3
2,210 Views
Last Modified: 2012-05-12
I have a routed port gig 0/3 on a 3650 switch, routing enabled.  I added "ip accounting output-packets" in hopes of gaining some insight as to what hosts are hogging bandwidth.  But alas I am not getting anything.  Is IP accounting available only on routers proper?  Same question for netflow.  I am pretty sure you get no netflow in this case.  Any other thought on how to tell what hosts are consuming the bandwidth on that interface?  Thanks!

interface GigabitEthernet0/3
 description  30Mbps link
 no switchport
 bandwidth 30000
 ip address 10.10.22.26 255.255.255.252
 ip accounting output-packets
 srr-queue bandwidth share 1 30 35 5
 queue-set 2
 priority-queue out
 mls qos trust cos
 auto qos trust



mccx-c3560-1#sho ip account
   Source           Destination              Packets               Bytes

Accounting data age is 24
0
Comment
Question by:amigan_99
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 2
3 Comments
 
LVL 26

Accepted Solution

by:
Soulja earned 500 total points
ID: 36568454
0
 
LVL 1

Author Closing Comment

by:amigan_99
ID: 36568525
That is helpful.  They do mention netflow however.  I have the enhanced image on the 3560.  Should the commands be there?  I don't see anything at global enable level.  This is how I configure on a 3845:

ip flow-cache timeout active 5
ip flow-export source GigabitEthernet0/0
ip flow-export version 5
ip flow-export destination 10.10.10.x 2055
ip flow-top-talkers
0
 
LVL 26

Expert Comment

by:Soulja
ID: 36568614
Yes, beginning with IOS version 12.2(58)SE. The switches support smart logging:

Check out this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst3750x_3560x/software/release/15.0_1_se/configuration/guide/3750X_scg.pdf

Look under the logging section.
0

Featured Post

Free NetCrunch network monitor licenses!

Only on Experts-Exchange: Sign-up for a free-trial and we'll send you your permanent license!

Here is what you get: 30 Nodes | Unlimited Sensors | No Time Restrictions | Absolutely FREE!

Act now. This offer ends July 14, 2017.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

If you are thinking of adopting cloud services, or just curious as to what ‘the cloud’ can offer then the leader according to Gartner for Infrastructure as a Service (IaaS) is Amazon Web Services (AWS).  When I started using AWS I was completely new…
WARNING:   If you follow the instructions here, you will wipe out your VTP and VLAN configurations.  Make sure you have backed up your switch!!! I recently had some issues with a few low-end Cisco routers (RV325) and I opened a case with Cisco TA…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

623 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question