Solved

Cisco Catalyst 4507R "unsupported module" - What do I need?

Posted on 2011-09-26
3
901 Views
Last Modified: 2012-05-12
I have a cisco 4507R (SupIV), with a WS-X4248-RJ45V that's showing up as unsupported. I thought that this card was compatible..

What do I need to do  to get PoE support on this switch? Do I need a different line card, updated IOS or better Sup?

Sh ver and sh mod all included below, see line 31 for the unsupported module.


Thanks for looking :-)
Switch#sh ver
Cisco Internetwork Operating System Software
IOS (tm) Catalyst 4000 L3 Switch Software (cat4000-IS-M), Version 12.1(12c)EW1,
EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Thu 24-Oct-02 23:05 by eaarmas
Image text-base: 0x00000000, data-base: 0x00CA7368

ROM: 12.1(12r)EW
Dagobah Revision 63, Swamp Revision 24

Switch uptime is 3 weeks, 3 days, 19 hours, 44 minutes
System returned to ROM by power-on
Running default software

cisco WS-C4507R (XPC8245) processor (revision 5) with 524288K bytes of memory.
Last reset from PowerUp
96 FastEthernet/IEEE 802.3 interface(s)
56 Gigabit Ethernet/IEEE 802.3 interface(s)
403K bytes of non-volatile configuration memory.

Configuration register is 0x102

Switch#sh mod all

Mod  Ports Card Type                              Model             Serial No.
----+-----+--------------------------------------+-----------------+-----------
 1      2  1000BaseX (GBIC) Supervisor(active)    WS-X4515          JXXXXXXXXXX
 3     48  10/100/1000BaseTX (RJ45)               WS-X4448-GB-RJ45  JXXXXXXXXXX
 4      0  Unsupported module                     WS-X4248-RJ45V    JXXXXXXXXXX
 5     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JXXXXXXXXXX
 6     48  10/100BaseTX (RJ45)                    WS-X4148-RJ       JXXXXXXXXXX
 7      6  1000BaseX (GBIC)                       WS-X4306-GB       JXXXXXXXXXX

 M MAC addresses                    Hw  Fw           Sw               Status
--+--------------------------------+---+------------+----------------+---------
 1 000e.xxxx.xxxx to 000e.xxxx.xxxx 1.1 12.1(12r)EW  12.1(12c)EW1, EA Ok
 3 000d.xxxx.xxxx to 000d.xxxx.xxxx 1.1                               Ok
 4 0011.xxxx.xxxx to 0011.xxxx.xxxx 2.2                               Other
 5 000e.xxxx.xxxx to 000e.xxxx.xxxx 3.1                               Ok
 6 000e.xxxx.xxxx to 000e.xxxx.xxxx 3.1                               Ok
 7 0011.xxxx.xxxx to 0011.xxxx.xxxx 3.0                               Ok

Open in new window

0
Comment
Question by:Wibble_
3 Comments
 
LVL 17

Accepted Solution

by:
rochey2009 earned 500 total points
ID: 36600835
0
 
LVL 18

Expert Comment

by:jmeggers
ID: 36601350
Agreed.  Your code version is very old, most likely the blade is newer than the code.
0
 

Author Closing Comment

by:Wibble_
ID: 36601430
Upgrading IOS did it.

TY :-)
0

Featured Post

Efficient way to get backups off site to Azure

This user guide provides instructions on how to deploy and configure both a StoneFly Scale Out NAS Enterprise Cloud Drive virtual machine and Veeam Cloud Connect in the Microsoft Azure Cloud.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Open a port on Cisco Router 1941 23 35
Cisco Switch Port Security 2 37
Do you think below two ipv6 routes are the same thing? 4 30
configure ASA Vlan Interface 14 46
This tutorial will go through the steps required to write a script that will back up the configuration settings of a HP-ProCurve switch. You will need to get the following things to follow this tutorial: Telnet Scripting Tool e.g. TST10.exe …
I eventually solved a perplexing problem setting up telnet for a new switch.  I installed a new Cisco WS-03560X-24P switch connected to an existing Cisco 4506 running a WS-X4013-10GE Sup II-Plus. After configuring vlans and trunking,  I could no…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

895 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

15 Experts available now in Live!

Get 1:1 Help Now