Solved

Cisco 4507 to Cisco 3750X extend (how to)

Posted on 2011-09-27
5
548 Views
Last Modified: 2012-05-12
I have a Cisco 4507 switch with 20 VLANs and it operates as the VTP server rank is 29 and a new cisco 3750X switch that I need to connect to the cisco 4507 and extend VLAN10 to the new switch and I need some help understanding what I need to do to establish/extend vlan 10 to the new switch.  I understand the VTP Client mode rank needs to be less than the VTP server and so I have set that up as 0 and VTP client so that issue is ready I have selected port to trunk and set encapsulation (if trunking is the best method to extend please advise), are there any other gottchas I need to be aware of?
0
Comment
Question by:commsecadm
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 3
  • 2
5 Comments
 
LVL 26

Accepted Solution

by:
Soulja earned 250 total points
ID: 36711301
If you are only extending vlan 10 to the stack.

interface typex/x                                          (connecting the switches on both ends)
switchport trunk encapsulation dot1q
switchport mode trunk
switchport trunk allowed vlan 10

0
 
LVL 26

Expert Comment

by:Soulja
ID: 36711308
Also make sure your vtp domain and passwords are the same also.
0
 

Author Comment

by:commsecadm
ID: 36711748
Soulja, Is there a password for the VTP  I thought we could just assign either VTP client or server (in our case client as we already have a master root bridge) but I have not seen a configuration for a password?  Please advise.

Thanks
0
 
LVL 26

Expert Comment

by:Soulja
ID: 36711969
If there is not password configured for your vtp domain then the new switch will not require one.
0
 

Author Closing Comment

by:commsecadm
ID: 36720724
Exactly the information i required to finish the job!  Thank you!!!
0

Featured Post

Resolve Critical IT Incidents Fast

If your data, services or processes become compromised, your organization can suffer damage in just minutes and how fast you communicate during a major IT incident is everything. Learn how to immediately identify incidents & best practices to resolve them quickly and effectively.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
Public IP Address - Subnet 4 44
Cisco 800 router unable to connect through TPG network 12 35
Layer 3 switch recommendation 15 60
VLAN 1 Line Protocol Down 9 40
In the hope of saving someone else's sanity... About a year ago we bought a Cisco 1921 router with two ADSL/VDSL EHWIC cards to load balance local network traffic over the two broadband lines we have, but we couldn't get the routing to work consi…
Quality of Service (QoS) options are nearly endless when it comes to networks today. This article is merely one example of how it can be handled in a hub-n-spoke design using a 3-tier configuration.
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
Here's a very brief overview of the methods PRTG Network Monitor (https://www.paessler.com/prtg) offers for monitoring bandwidth, to help you decide which methods you´d like to investigate in more detail.  The methods are covered in more detail in o…

733 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question