One more Clock configuration issue

I have the below device, on which either there is no NTP or SNTP, Just wanted to know how these devices get time updated? Is there only one way of creating manually ?


Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(21a)

Kindly suggest and thanks for your ti me.

Regards.
raviv0731Asked:
Who is Participating?

[Product update] Infrastructure Analysis Tool is now available with Business Accounts.Learn More

x
I wear a lot of hats...

"The solutions and answers provided on Experts Exchange have been extremely helpful to me over the last few years. I wear a lot of hats - Developer, Database Administrator, Help Desk, etc., so I know a lot of things but not a lot about one thing. Experts Exchange gives me answers from people who do know a lot about one thing, in a easy to use platform." -Todd S.

rogerhuntCommented:
Does the command config time ntp come up?
0
raviv0731Author Commented:
NO, it didn't come up.  When i see sh clock detai, it just shows "User configured".
0
rogerhuntCommented:
Just to check does it allow you to enter the time manually? config time manual 12/24/2011 08:25:00
0
Powerful Yet Easy-to-Use Network Monitoring

Identify excessive bandwidth utilization or unexpected application traffic with SolarWinds Bandwidth Analyzer Pack.

raviv0731Author Commented:
Yes,

it allows me to do manual by " Clock set" command
0
rogerhuntCommented:
Looking at the manual on this IOS http://www.cisco.com/en/US/docs/wireless/access_point/12.4.25d.JA/Configuration/guide/12.4.25d.JA.cg.pdf, it shows that the "Clock Set" command is ran in EXEC mode and the SNTP server is enabled in global configuration mode.  I assume you are in global configuration mode when looking for the SNTP commands?

Configure Terminal
sntp server {address | hostname}
0
raviv0731Author Commented:
I do "Clock set" command from EXEC or enable mode.

xxxxx-AP01#clock se
xxxxx-AP01#clock set ?
  hh:mm:ss  Current Time

When i try from Global Config mode,  don't get any SNTP



xxxx-AP01(config)#sntp
                       ^
% Invalid input detected at '^' marker.

When i type ntp and enter , some strange behavour,it says "Incomplete" but it actually doesn't resolve to any NTP command.


IR-B1D1-AP01(config)#ntp
% Incomplete command.

0
rogerhuntCommented:
Does NTP ? give you any additional information?
0
raviv0731Author Commented:
Nothing at this point !! when i typed NTP in config mode, there is no any other following command with that and if i press enter after typing NTP, it gives above output like " Incomplete command".  Actually I Can't type anything after this NTP  in Global mode.
0
raviv0731Author Commented:
HI ,

Can you please let me know one thing ? How to check time on Web interface for ProCurve 1800-24G J90288 ?

Thanks for your support and time.

Regards.
0
raviv0731Author Commented:
No problem i am done with question i asked about procurve 1800-24G J90288.

Thanks.
0
lomejordeestoCommented:
I have a 1232 AP and I can configure SNTP for clock synchronization, it just that there is a bug and in context help it says that is a unknown command
Check this command
sntp server x.x.x.x
x.x.x.x = ip address of NTP server
just copy paste and enter don't look at the context help.
0
rogerhuntCommented:
See if this is similar to the 1800-24G web interface:

1. Navigate to Network Setup -> SNTP in the switch menu
2. Select the Enable SNTP check-box
3. Enter your NTP server IP address in the appropriate field and apply the settings
4. Navigate to Network Setup -> Time Zone
5. Select your time zone from the drop down and apply the settings
6. Navigate to Network Setup -> Daylight Saving Time
7. Ensure the settings are correct for your time zone
8. The time will take a little while to sync. Navigate to Network Setup -> SNTP to check whether it is right.

Taken from http://linuxman.wikispaces.com/ProCurve+1810G-8+setup
0

Experts Exchange Solution brought to you by

Your issues matter to us.

Facing a tech roadblock? Get the help and guidance you need from experienced professionals who care. Ask your question anytime, anywhere, with no hassle.

Start your 7-day free trial
raviv0731Author Commented:
Hi lomejordeesto,

i have tried to do directly ntp server command and it accepted but i still see the message" User configured time" in the output for sh clock detail. I don't get any info for SNTP.

HI Rogerhunt,

ITs not working that way.

0
raviv0731Author Commented:
can i have anyone's help on this?
Regards.
0
It's more than this solution.Get answers and train to solve all your tech problems - anytime, anywhere.Try it for free Edge Out The Competitionfor your dream job with proven skills and certifications.Get started today Stand Outas the employee with proven skills.Start learning today for free Move Your Career Forwardwith certification training in the latest technologies.Start your trial today
Networking Protocols

From novice to tech pro — start learning today.