Solved

Juniper Netscreen SSG20

Posted on 2012-03-15
3
901 Views
Last Modified: 2012-03-24
I have a network with this router. Internal IP, on 192.168 range 24bit. We have clients from our head office coming to the network who need to use a recenetly installed MPLS line on a 10.81 range. Therefore their DG should be the MPLS router and my current users  192.168.1.254. What rule process should i use to incorporate routing for the new MPLS please?
0
Comment
Question by:techies123
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
3 Comments
 
LVL 4

Accepted Solution

by:
schmitty007 earned 500 total points
ID: 37725572
OK so you have your Juniper SSG and you have a second Gateway which is routing for your new MPLS connection, correct? And does your side of that MPLS router have a 192.168.x.x/24 IP on an interface? Or I am misunderstanding.

If this is the case you can simply build a route in your Juniper to route any traffic looking for 10.81.x.x/24 or whatever subnet you are using to the IP of the MPLS router.
So if you use to GUI of your SSG you would login go to network -> Routing -> Destination.
In the upper right hand corner I believe you have a New button and you want to have trust-vr in the drop down.

You will have several fields to input your data.
IP ADDRESS/NETMASK 10.81.x.0 /24
Put the bullet in Gateway
Your interface needs to match your Bgroup or what ever interface your 192.168.x.0/24 network is on.
Gateway IP   will be the LAN side IP of the MPLS router.
Everything else you can leave default and you can add a description up to you.

Or if you are stating you have two different subnets in the same office you can simply put one of your Ethernet interfaces in the Juniper on the 10.81.x.0/24 network and let the Juniper route across the interfaces.

If these are not relevant and if you want to post up a small network diagram it would be helpful. Then I or someone else maybe able to assist further.

Regards
0
 

Author Closing Comment

by:techies123
ID: 37748867
We did it using RRAS in Server 2008. appreciate the steer
0

Featured Post

Free Tool: Subnet Calculator

The subnet calculator helps you design networks by taking an IP address and network mask and returning information such as network, broadcast address, and host range.

One of a set of tools we're offering as a way of saying thank you for being a part of the community.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

Suggested Solutions

Title # Comments Views Activity
DHCP Server 14 103
What problem can Native VLAN mismatch causes 4 59
Cisco WRVS4400N 11 60
Extended ping 6 25
In the hope of saving someone else's sanity... About a year ago we bought a Cisco 1921 router with two ADSL/VDSL EHWIC cards to load balance local network traffic over the two broadband lines we have, but we couldn't get the routing to work consi…
There are two basic ways to configure a static route for Cisco IOS devices. I've written this article to highlight a case study comparing the configuration of a static route using the next-hop IP and the configuration of a static route using an outg…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

761 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question