Solved

HP v1910 Routing

Posted on 2012-03-21
7
4,553 Views
Last Modified: 2012-03-26
Hi Everyone

I have a HP v1910 which is meant to be capable of routing, unfortunately I can't get it to work. I have 2 VLANS each with seperate subnet, I have a device on each Subnet, but they're unable to ping or communicate with each other.

Another person had a similar problem with the same switch -

http://www.experts-exchange.com/Hardware/Networking_Hardware/Switches/Q_27482832.html

The solution was to run

conf t
ip routing

Open in new window


From the cli.. the problem is, none of these commands appear on my switch. All I have see is

  initialize  Delete the startup configuration file and reboot system
  ipsetup     Specify the IP address of the VLAN interface 1 
  password    Specify password of local user
  ping        Ping function 
  quit        Exit from current command view
  reboot      Reboot system
  summary     Display summary information of the device.
  upgrade     Upgrade the system boot file or the Boot ROM progra

Open in new window


Can anybody advise?
0
Comment
Question by:EVIL3
  • 4
  • 3
7 Comments
 
LVL 6

Expert Comment

by:RKinsp
ID: 37749176
Hello,

From CLI, you have to type in "system-view" to enable configuration mode.

You have to configure IPs on your VLANs for routing to work and enable routing.

Good luck,
RK
0
 
LVL 6

Expert Comment

by:RKinsp
ID: 37749190
Also, how are you connected to the switch? console cable?
0
 

Author Comment

by:EVIL3
ID: 37749346
Hi RKinsp

"system-view" does not work, I should also mention the HPv1910 are re-badged 3com switches. So its not the "standard" OS HP put into their pro-curve switches.

With regards to connectivity, I've tried both SSH and Console cable, both give the same mention options I outlined above.
0
Enabling OSINT in Activity Based Intelligence

Activity based intelligence (ABI) requires access to all available sources of data. Recorded Future allows analysts to observe structured data on the open, deep, and dark web.

 
LVL 6

Assisted Solution

by:RKinsp
RKinsp earned 250 total points
ID: 37749610
Yep, it is the 3com 2900. System-view is a 3com command, however the 2900 is CLI limited and most configurations are via web.

Can you access the web interface?
0
 

Assisted Solution

by:EVIL3
EVIL3 earned 0 total points
ID: 37749674
Hi RKinsp,

I've been trying it via the web interface aswell.

I'm trying a very simple experiment with 1 switch and 2 PC's

Configured are

VLAN 1 - 192.168.0.142/24
VLAN 51 - 192.168.71.142/24

On VLAN 1 is PC1 with IP 192.168.0.111
On VLAN 51 is PC2 with IP 192.168.71.150

All I want to do is ping from PC1 to PC2... I've tried different combinations of Tagged and Untagged, yet still no joy.

I can ping the VLAN 51 IP (192.168.71.142) from PC1 if I setup a route on the PC (setting 192.168.0.142 as gateway).. but the same trick will not allow me to ping PC2.

Thanks
0
 

Accepted Solution

by:
EVIL3 earned 0 total points
ID: 37749759
doh!!

It does work - I had just configured the gateway incorrectly!

Thanks for your help.
0
 

Author Closing Comment

by:EVIL3
ID: 37764979
Thanks for your help.
0

Featured Post

Why You Should Analyze Threat Actor TTPs

After years of analyzing threat actor behavior, it’s become clear that at any given time there are specific tactics, techniques, and procedures (TTPs) that are particularly prevalent. By analyzing and understanding these TTPs, you can dramatically enhance your security program.

Join & Write a Comment

Suggested Solutions

I eventually solved a perplexing problem setting up telnet for a new switch.  I installed a new Cisco WS-03560X-24P switch connected to an existing Cisco 4506 running a WS-X4013-10GE Sup II-Plus. After configuring vlans and trunking,  I could no…
Shadow IT is coming out of the shadows as more businesses are choosing cloud-based applications. It is now a multi-cloud world for most organizations. Simultaneously, most businesses have yet to consolidate with one cloud provider or define an offic…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

706 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question

Need Help in Real-Time?

Connect with top rated Experts

18 Experts available now in Live!

Get 1:1 Help Now