Solved

GNS3 Junos Olive and EX4200 Image Compatibility

Posted on 2012-03-21
6
3,435 Views
Last Modified: 2012-03-22
Hello Experts,

 

Some of you maybe familiar with GNS3 simulator labs.

 

I have managed to install an Olive image for Juniper routers, however I was wondering if its possible to install an EX4200 image on the router and have it simulate an EX4200?

 

You advice will be greatly appreciated.

 

Cheers

 

Carlton
0
Comment
Question by:cpatte7372
[X]
Welcome to Experts Exchange

Add your voice to the tech community where 5M+ people just like you are talking about what matters.

  • Help others & share knowledge
  • Earn cash & points
  • Learn & ask questions
  • 4
  • 2
6 Comments
 
LVL 18

Expert Comment

by:deimark
ID: 37749577
Sadly not bud

The olive images do not have the required layer 2 features here but the base Junos features for routing etc will all still work fine

At the moment there is no fully featured VM version of junos less for Junipers own Junosphere where you can rent some (virtual) devices.  These are similar to Olive but are fully supported from Juniper and are based on SRX architecture so they do the stateful firewalling as well.  However the same limitation on layer 2 switching still applies sadly..  We do expect layer 2 to be added this year though.

HTH
0
 

Author Comment

by:cpatte7372
ID: 37749729
deimark

Thanks dude.

Excellent advice

Cheers
0
 

Author Comment

by:cpatte7372
ID: 37750516
Deimark,

How will we know when itll be added?

Cheers
0
Simple, centralized multimedia control

Watch and learn to see how ATEN provided an easy and effective way for three jointly-owned pubs to control the 60 televisions located across their three venues utilizing the ATEN Control System, Modular Matrix Switch and HDBaseT extenders.

 
LVL 18

Accepted Solution

by:
deimark earned 500 total points
ID: 37751601
Sadly juniper don't provide exact dates for features on the road map so we will just need to wait unfortunately. However you can test the majority of switch features on te SRX series as well juniper have some smaller EX series boxes out there.

Have a look at prices for srx100s and ex2200c. These are small forms factor and will give you the chance to learn the kit.

HTH
0
 

Author Comment

by:cpatte7372
ID: 37752902
deimark

Thanks again  mate.

Really appreciate it.

Cheers
0
 

Author Closing Comment

by:cpatte7372
ID: 37752907
Cheers
0

Featured Post

Free Tool: Site Down Detector

Helpful to verify reports of your own downtime, or to double check a downed website you are trying to access.

One of a set of tools we are providing to everyone as a way of saying thank you for being a part of the community.

Question has a verified solution.

If you are experiencing a similar issue, please ask a related question

I have seen some questions on problems with SSH/telnet access to Cisco routers that may occur despite the fact that from a PC connected to your LAN, Internet connectivity is in place and users can access Internet sites without any issues.  There are…
We've been using the Cisco/Linksys RV042 for years as: - an internet Gateway - a site-to-site VPN device - a leased line site-to-site subnet-to-subnet interface (And, here I'm assuming that any RV0xx behaves the same way as an RV042.  So that's …
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…
After creating this article (http://www.experts-exchange.com/articles/23699/Setup-Mikrotik-routers-with-OSPF.html), I decided to make a video (no audio) to show you how to configure the routers and run some trace routes and pings between the 7 sites…

696 members asked questions and received personalized solutions in the past 7 days.

Join the community of 500,000 technology professionals and ask your questions.

Join & Ask a Question